No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

FusionServer Pro E9000 Server iBMC (Earlier Than V250) User Guide 31

This document describes the underlying management software Intelligent Baseboard Management Controller (iBMC) of the servers.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Server Commands

Server Commands

This topic describes all the commands about server.

Querying and Setting the Booting Device (bootdevice)

Function

The bootdevice command is used to query and set the booting device.

Format

ipmcget -d bootdevice

ipmcset -d bootdevice -v <option>

Parameters

Parameter Description Value
option Indicates the number of the booting device.
  • 0: cancels the forcible startup.

  • 1: starts from the PXE.

  • 2: starts from the default hard disk.

  • 5: starts from the default CD/DVD.

  • 6: accesses the BIOS Setup menu upon server startup.

  • 0xF: starts from the FDD or the first mobile media.

Usage Guidelines

The settings take effect immediately after configuration and become invalid after the next startup.

Example

NOTE:

The displayed information contains Unspecified, it indicates that the forcible booting parameters of the device are not set.

# Start the device from the default hard disk.

iBMC:/->ipmcset -d bootdevice -v 2
Set boot device successfully.

# Query the changed booting device.

iBMC:/->ipmcget -d bootdevice
Boot device:    Force boot from default Hard-drive

Setting the Resetting Mode of the Server (frucontrol)

Function

The frucontrol command is used to set the resetting mode of the server.

Format

ipmcset [-t fru0] -d frucontrol -v <option>

Parameters

Parameter Description Value

option

Indicates the resetting mode of the server.

  • 0: forced system reset the server.
  • 2: forced power cycle the server.

Usage Guidelines

The switch modules do not support the command.

A power-off server does not support the command.

Example

# Forcibly reset the server.

iBMC:/->ipmcset -d frucontrol -v 0
WARNING: The operation may have many adverse effects.
Do you want to continue?[Y/N]:y
FRU control fru0 (forced system reset) successfully.

# Forcibly power cycle the server.

iBMC:/->ipmcset -d frucontrol -v 2
WARNING: The operation may have many adverse effects.
Do you want to continue?[Y/N]:y
FRU control fru0 (forced power cycle) successfully.

Querying and Setting the Power State of the Server (powerstate)

Function

The powerstate command is used to query and set the power state of the server.

Format

ipmcget [-t fru0] -d powerstate

ipmcset [-t fru0] -d powerstate -v <option>

Parameters

Parameter Description Value

option

Indicates the state to be set.

  • 0: normal power off
  • 1: power on
  • 2: forced power off

Usage Guidelines

The switch modules do not support the command.

The power-off command is invalid for a server that has been powered off.

Example

# Power on the server.

iBMC:/->ipmcset -d powerstate -v 1
WARNING: The operation may have many adverse effects
Do you want to continue?[Y/N]:y
Control fru0 power on successfully.

# Query the power state.

iBMC:/->ipmcget -d powerstate
Power state   : On
Hotswap state : M4

Querying and Setting the Power-Off Timeout Period for the Server (shutdowntimeout)

Function

The shutdowntimeout command is used to query and set the power-off timeout period for the server.

The power-off timeout period refers to the maximum time during which iBMC waits for the operating system (OS) to power off after the power-off operation is triggered. If the OS does not power off after the timeout period ends, iBMC forcibly powers off the OS.

Format

ipmcget [-t fru0] -d shutdowntimeout

ipmcset [-t fru0] -d shutdowntimeout -v <time>

Parameters

Parameter Description Value
time
  • specifies to disable the Power-off Timeout Period function for the server.
  • Specifies the value of the power-off timeout period to be set.
  • If the value is 0, the Power-off Timeout Period function is disabled for the server.
  • The value is an integer and the unit is second. The value range is 10 to 1800.

Usage Guidelines

None

Example

# Set the power-off timeout period for the server to 600 second, if power-off timeout period is set to ON on the web page.

iBMC:/->ipmcset -d shutdowntimeout -v 600
Set shutdown timeout successfully.

# You can view the power-off timeout period, if power-off timeout period is set to ON on the web page.

iBMC:/->ipmcget -d shutdowntimeout
Graceful shutdown timeout state:    enabled
Graceful shutdown timeout value:    600 s

# You can view the power-off timeout period function that is disabled, if power-off timeout period is set to OFF on the web page.

iBMC:/->ipmcget -d shutdowntimeout
Graceful shutdown timeout state:    disabled

# You can set the power-off timeout period, if power-off timeout period is set to OFF on the web page. The power-off timeout periodfunction status is ON on the web page after the setting.

iBMC:/->ipmcset -d shutdowntimeout -v 600
Set shutdown timeout successfully.

# If power-off timeout period is set to ON on the web page, you can disable the power-off timeout period function for the server.

iBMC:/->ipmcset -d shutdowntimeout -v 0
Set shutdown timeout successfully.

Querying the MAC Address of the Network Interface on the Main Board (macaddr)

Function

The macaddr command is used to query the MAC address of the network interface on the main board.

Format

ipmcget -d macaddr

Parameters

None

Usage Guidelines

None

Example

# Query the MAC address of network interface on the main board.

iBMC:/->ipmcget -d macaddr
Type       | Name       | Mac Address
LOM        | Port1      | 20:0b:c7:2a:e6:0b
LOM        | Port2      | 20:0b:c7:2a:e6:0c
LOM        | Port3      | 20:0b:c7:2a:e6:0d
LOM        | Port4      | 20:0b:c7:2a:e6:0e

Clearing the BIOS Flash (clearcmos)

Function

The clearcmos command is used to delete all user-defined information from the BIOS flash.

Format

ipmcset -d clearcmos

Parameters

None

Usage Guidelines

None

Example

# Clear the BIOS flash.

iBMC:/->ipmcset -d clearcmos
WARNING: The operation may have many adverse effects
Do you want to continue?[Y/N]:y
Clear CMOS successfully.

Querying RAID Controller Card Information (raid)

Function

The raid command is used to query RAID controller card information.

Format

ipmcget -d raid -v <option>

Parameters

Parameter

Description

Value

option

Specifies the ID of a RAID controller card.

  • 0 to 255: indicates a specific RAID controller card.
  • all: indicates all RAID controller cards.

Usage Guidelines

The queried RAID controller card must support out-of-band management. You can refer to the Technical Specifications section in the Huawei V2 and V3 Server RAID Controller Card User Guide to determined whether the RAID card supports the iBMC out-of-band management.

Example

# Query information about RAID controller card 0.

iBMC:/->ipmcget -d raid –v 0
RAID Controller #0 Information
----------------------------------------------------------------------
Controller Name                               : SAS3108
Controller Type                               : LSI SAS3108
Component Name                                : RAID Card1
Support Out-of-Band Management                : Yes
Controller Mode                               : RAID
Controller Health                             : Normal
Firmware Version                              : 4.270.00-4382
NVDATA Version                                : 3.1411.00-0023
Memory Size                                   : 1024 MB
Device Interface                              : SAS_12G
SAS Address                                   : 50030130f0900000
Controller Cache Is Pinned                    : No
Maintain PD Fail History across Reboot        : Yes
DDR ECC Count                                 : 0

BBU Status                                    : Present
BBU Type                                      : CVPM02
BBU Health                                    : Normal

PHY Status                                    : 
	PHY #0 :
		Invalid Dword Count           : 0
		Loss Dword Sync Count         : 0
		PHY Reset Problem Count       : 0
		Running Disparity Error Count  : 0

	PHY #1 :
		Invalid Dword Count           : 0
		Loss Dword Sync Count         : 0
		PHY Reset Problem Count       : 0
		Running Disparity Error Count  : 0

	PHY #2 :
		Invalid Dword Count           : 0
		Loss Dword Sync Count         : 0
		PHY Reset Problem Count       : 0
		Running Disparity Error Count  : 0

	PHY #3 :
		Invalid Dword Count           : 0
		Loss Dword Sync Count         : 0
		PHY Reset Problem Count       : 0
		Running Disparity Error Count  : 0

	PHY #4 :
		Invalid Dword Count           : 0
		Loss Dword Sync Count         : 0
		PHY Reset Problem Count       : 0
		Running Disparity Error Count  : 0

	PHY #5 :
		Invalid Dword Count           : 0
		Loss Dword Sync Count         : 0
		PHY Reset Problem Count       : 0
		Running Disparity Error Count  : 0

	PHY #6 :
		Invalid Dword Count           : 0
		Loss Dword Sync Count         : 0
		PHY Reset Problem Count       : 0
		Running Disparity Error Count  : 0

	PHY #7 :
		Invalid Dword Count           : 0
		Loss Dword Sync Count         : 0
		PHY Reset Problem Count       : 0
		Running Disparity Error Count  : 0
----------------------------------------------------------------------

Querying Logical Disk Information (ldinfo)

Function

The ldinfo command is used to query information about logical disks managed by a RAID controller card.

Format

ipmcget -d ldinfo -v <ctrlid> <option>

Parameters

Parameter

Description

Value

ctrlid

Specifies the ID of the RAID controller that manages the target logical disk.

0 to 255
option

Specifies the ID of a logical disk.

  • 0 to 255: indicates a specific logical disk.
  • all: indicates all logical disks managed by a RAID controller.

Usage Guidelines

The queried RAID controller card must support out-of-band management. You can refer to the Technical Specifications section in the Huawei V2 and V3 Server RAID Controller Card User Guide to determined whether the RAID card supports the iBMC out-of-band management.

Example

# Query information about logical disk 0 managed by RAID controller 0.

iBMC:/->ipmcget -d ldinfo –v 0 0
Logical Drive Information
----------------------------------------------------------------------
Target ID                                : 0
Type                                     : RAID1
State                                    : Optimal
Defalut Read Policy                      : Read Ahead
Defalut Write Policy                     : Write Back
Defalut Cache Policy                     : Direct IO
Current Read Policy                      : Read Ahead
Current Write Policy                     : Write Back
Current Cache Policy                     : Direct IO
Span depth                               : 1
Number of drives per span                : 2
Stripe Size                              : 256 KB
Total Size                               : 75340 MB
Disk Cache Policy                        : Disk's Default
Consistency Checking                     : No
Bootable                                 : Yes
PD participating in LD(slot#)            : 5,7
----------------------------------------------------------------------

# Query information about all logical disks managed by RAID controller 0.

iBMC:/->ipmcget -d ldinfo –v 0 all
Logical Drive Information
----------------------------------------------------------------------
Target ID                                : 0
Type                                     : RAID1
State                                    : Optimal
Defalut Read Policy                      : Read Ahead
Defalut Write Policy                     : Write Back
Defalut Cache Policy                     : Direct IO
Current Read Policy                      : Read Ahead
Current Write Policy                     : Write Back
Current Cache Policy                     : Direct IO
Span depth                               : 1
Number of drives per span                : 2
Stripe Size                              : 256 KB
Total Size                               : 75340 MB
Disk Cache Policy                        : Disk's Default
Consistency Checking                     : No
Bootable                                 : Yes
PD participating in LD(slot#)            : 5,7
----------------------------------------------------------------------

Querying Physical Disk Information (pdinfo)

Function

The pdinfo command is used to query information about physical disks managed by a RAID controller card.

Format

ipmcget -d pdinfo -v <ctrlid> <option>

Parameters

Parameter

Description

Value

ctrlid

Specifies the ID of the RAID controller that manages the target physical disk.

0 to 255
option

Specifies the ID of a physical disk.

  • 0 to 255: indicates a specific physical disk.
  • all: indicates all physical disks managed by a RAID controller.

Usage Guidelines

The queried RAID controller card must support out-of-band management. You can refer to the Technical Specifications section in the Huawei V2 and V3 Server RAID Controller Card User Guide to determined whether the RAID card supports the iBMC out-of-band management.

Example

# Query information about physical disk 2 managed by RAID controller 0.

iBMC:/->ipmcget -d pdinfo –v 0 2
Physical Drive Information
----------------------------------------------------------------------
ID                                       : 2
Device Name                              : Disk2
Manufacturer                             : HGST
Serial Number                            : 0QV4R10A
Model                                    : HUSMM1640ASS204
Firmware Version                         : c280
Health Status                            : Normal
Firmware Status                          : UNCONFIGURED GOOD
Power State                              : Spun Up
Media Type                               : SSD
Interface Type                           : SAS
Interface Speed                          : 12.0Gbps
Link Speed                               : 12.0Gbps
Drive Temperature                        : 34(Celsius)
Capacity                                 : 372 GB
Hot Spare                                : None
Rebuild in Progress                      : No
Patrol Read in Progress                  : No
Remnant Media Wearout                    : 100%
SAS Address(0)                           : 5000cca04e0890c5
SAS Address(1)                           : 0000000000000000

Media Error Count                        : 0
Prefail Error Count                      : 0
Other Error Count                        : 0
----------------------------------------------------------------------

# Query information about all physical disks managed by RAID controller 0.

iBMC:/->ipmcget -d ldinfo –v 0 all
Physical Drive Information
----------------------------------------------------------------------
ID                                       : 2
Device Name                              : Disk2
Manufacturer                             : HGST
Serial Number                            : 0QV4R10A
Model                                    : HUSMM1640ASS204
Firmware Version                         : c280
Health Status                            : Normal
Firmware Status                          : UNCONFIGURED GOOD
Power State                              : Spun Up
Media Type                               : SSD
Interface Type                           : SAS
Interface Speed                          : 12.0Gbps
Link Speed                               : 12.0Gbps
Drive Temperature                        : 34(Celsius)
Capacity                                 : 372 GB
Hot Spare                                : None
Rebuild in Progress                      : No
Patrol Read in Progress                  : No
Remnant Media Wearout                    : 100%
SAS Address(0)                           : 5000cca04e0890c5
SAS Address(1)                           : 0000000000000000

Media Error Count                        : 0
Prefail Error Count                      : 0
Other Error Count                        : 0
----------------------------------------------------------------------

Physical Drive Information
----------------------------------------------------------------------
ID                                       : 5
Device Name                              : Disk5
Manufacturer                             : ATA
Serial Number                            : BTWA504605AX080MGN
Model                                    : INTEL SSDSC2BB080G6
Firmware Version                         : 0140
Health Status                            : Normal
Firmware Status                          : ONLINE
Power State                              : Spun Up
Media Type                               : SSD
Interface Type                           : SATA
Interface Speed                          : 6.0Gbps
Link Speed                               : 6.0Gbps
Drive Temperature                        : 31(Celsius)
Capacity                                 : 74 GB
Hot Spare                                : None
Rebuild in Progress                      : No
Patrol Read in Progress                  : No
Remnant Media Wearout                    : 99%
SAS Address(0)                           : 500e004aaaaaaa05
SAS Address(1)                           : 0000000000000000

Media Error Count                        : 0
Prefail Error Count                      : 0
Other Error Count                        : 0
----------------------------------------------------------------------
Translation
Download
Updated: 2019-08-01

Document ID: EDOC1000058833

Views: 206544

Downloads: 1935

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next