No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

CX11x, CX31x, CX710 (Earlier Than V6.03), and CX91x Series Switch Modules V100R001C10 Log Reference 07

This document describes the parameters, meaning, possible causes, and solution of logs.

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
About This Document

About This Document

Purpose

This document describes the parameters, meaning, possible causes, and solution of logs.

This document provides a complete set of logs, which helps intended readers check the running status of the device, analyze the network status, and locate the problem cause, so as to provide a reference for system diagnosis and maintenance.

The product features and commands for the Ethernet switching plane of the switch modules vary according to the software version. For details, see the documents listed in the following table.

NOTE:

Run the display version command in the switching plane CLI and select a reference document based on the Switch Version or Software Versiondisplayed in the command output.

Huawei Support Website Version

Ethernet Switching Plane Software Version

Reference Document

V100R001C00 or V100R001C00SPCxxx

1.1.0.200.3

See the CX110&CX31x Series Switch Modules V100R001C00 Log Reference .

1.1.3.100.3

1.1.3.300.3

1.1.3.300.5

1.1.3.301.6

1.1.3.330.13

1.2.1.0.19

1.2.1.0.21

2.23

2.26

2.29

V100R001C10 or V100R001C10SPCxxx

1.2.1.0.39

See this document.

Versions in the x.xx format, except 2.23, 2.26, and 2.29.

NOTE:

NOTE:

2.05 and later versions are displayed in the x.xx format.

Intended Audience

This document is intended for:

  • Data configuration engineers

  • Commissioning engineers

  • Network monitoring engineers

  • System maintenance engineers

Symbol Conventions

The symbols that may be found in this document are defined as follows.

Symbol

Description

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance deterioration, or unanticipated results.

NOTICE is used to address practices not related to personal injury.

Calls attention to important information, best practices and tips.

NOTE is used to address information not related to personal injury, equipment damage, and environment deterioration.

Command Conventions

The command conventions that may be found in this document are defined as follows.

Convention

Description

Boldface

The keywords of a command line are in boldface.

Italic

Command arguments are in italics.

[ ]

Items (keywords or arguments) in brackets [ ] are optional.

{ x | y | ... }

Optional items are grouped in braces and separated by vertical bars. One item is selected.

[ x | y | ... ]

Optional items are grouped in brackets and separated by vertical bars. One item is selected or no item is selected.

{ x | y | ... }*

Optional items are grouped in braces and separated by vertical bars. A minimum of one item or a maximum of all items can be selected.

[ x | y | ... ]*

Optional items are grouped in brackets and separated by vertical bars. Several items or no item can be selected.

&<1-n>

The parameter before the & sign can be repeated 1 to n times.

#

A line starting with the # sign is comments.

Interface Number Conventions

Interface numbers used in this manual are examples. In device configuration, use the existing interface numbers on devices.

Change History

Issue

Date

Description

07

2019-08-02

This issue is the seventh official release.

06

2017-09-04

This issue is the sixth official release, and includes the following changes:

Deleted information about ISSU.

05

2017-03-27

This issue is the fifth official release, and includes the following changes:

Modified the relationships between switching plane software versions and reference documents in About This Document.

04

2015-12-01

This issue is the fourth official release.

03

2015-07-17

This issue is the third official release.

02

2015-02-16

This issue is the second official release.

01

2014-11-10

This issue is the first official release.

Translation
Download
Updated: 2019-08-09

Document ID: EDOC1000059108

Views: 71588

Downloads: 342

Average rating:
This Document Applies to these Products

Related Version

Related Documents

Share
Previous Next