No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

X6800 Server V100R003 User Guide 13

This document describes the Huawei X6800 server (X6000 for short) in terms of its appearance, features, specifications, system components, device installation, cable connections, and installation verification.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Logging In to the HMM CLI

Logging In to the HMM CLI

The HMM does not have a WebUI. You can use the following methods to log in to the HMM CLI to manage servers.

Logging In to the HMM CLI Through the Aggregated Management Network Port

Scenarios

Log in to the HMM CLI through the front aggregated management network port on the mounting ear or the rear aggregated management network port on the HMM.

NOTE:

If both the front and rear aggregated management network ports are connected to the management network, the front aggregated management network port will be used because it has higher priority, and the rear aggregated management network port will be disabled by the software.

Figure 4-3 and Figure 4-4 shows the positions of the aggregated management network ports.

Figure 4-3 Position of the rear aggregated management network port

Figure 4-4 Position of the front aggregated management network port

Prerequisites

Conditions

The X6800 has been powered on.

Data

  • IP address of the HMM management network port
  • User name and password for logging in to the HMM

Table 4-4 lists the default data for the HMM.

Table 4-4 Default data for the HMM

Default User

Default Password

Default IP Address

Default Subnet Mask

root

Huawei12#$

  • HMM V1.62 and later:

    10.10.1.200

  • Versions earlier than HMM V1.62:

    192.168.2.1

255.255.255.0

Software

PuTTY.exe (third-party software)

Procedure
Connect the client to the aggregated management network port.
  1. Connect the client to the front aggregated management network port on the mounting ear or the rear aggregated management network port on the HMM using a network cable, as shown in Figure 4-5 and Figure 4-6.
    Figure 4-5 Connecting the client to the front aggregated management network port

    Figure 4-6 Connecting the client to the rear aggregated management network port

    Set the client address.

  2. Set the IP address, subnet mask, or route of the client to enable the client to interconnect with the aggregated management network port.

    On the client, choose Start > Run, enter cmd, and click OK. Then, run the Ping IP address of the aggregated management network port command to check whether the aggregated management network port is reachable.

    Log in to the HMM CLI.

  3. On the client, double-click PuTTY.exe.

    The PuTTY Configuration window is displayed, as shown in Figure 4-7.

    Figure 4-7 PuTTY Configuration

  4. Set the login parameters.

    The parameters are described as follows:

    • Host Name (or IP address): Enter the IP address of the aggregated management network port, for example, 192.168.2.1.
    • Port: Retain the default value 22.
    • Connection type: Retain the default value SSH.
    • Close window on exit: Retain the default value Only on clean exit.
    NOTE:

    After you set Host Name (or IP address) and then Saved Sessions and click Save, you can simply double-click the saved settings under Saved Sessions to log in to the server.

  5. Click Open.

    The PuTTY window is displayed. Then the message "login as:" is displayed, prompting you to enter a user name.

    NOTE:
    • If you log in to the server for the first time, the PuTTY Security Alert dialog box is displayed. If you trust this site, click Yes. The PuTTY window is displayed.
    • If the entered user name or password is incorrect during server login, PuTTY must be connected again.
  6. Enter the user name and password as prompted.

    After login, the host name of the device is displayed on the left of the prompt.

Logging In to the HMM CLI Through the Management Network Port on the Server Node

Scenarios

Log in to the HMM CLI through the iBMC management network port on the server node.

NOTE:
  • You can log in to the HMM CLI through the HMM management network port or server node iBMC management network port if 1) you are connected to both the server node iBMC management network port and the aggregated management network port, and 2) transparent transmission is enabled on the server node.
  • If you log in to the HMM CLI through the server node management network port, the management network port mode must be the fixed or automatic mode.

Figure 4-8 shows the position of the iBMC management network port on the server node.

Figure 4-8 Position of the iBMC management network port on the server node

Prerequisites

Conditions

The X6800 has been powered on.

Data

  • IP address of the iBMC management network port on the server node
  • User name and password for logging in to the iBMC of the server node

Software

PuTTY.exe (third-party software)

Procedure

Connect the client to the iBMC management network port on the server node.

  1. Connect the client to the iBMC management network port on the server node using a network cable, as shown in Figure 4-9.
    Figure 4-9 Connecting the client to the management network port on the server node

    Set the client address.

  2. Set the IP address, subnet mask, or route of the client to enable the client to interconnect with the iBMC management network port on the server node.

    On the client, choose Start > Run, enter cmd, and click OK. Then, run the Ping IP address of the iBMC management network port command to check whether the iBMC management network port is reachable.

    Log in to the iBMC WebUI of the server node.

    For details, see Logging In to the iBMC CLI or WebUI of the Server Node Through the iBMC Management Network Port.

    Enable the transparent transmission function.

  3. In the navigation tree on the iBMC WebUI of the server node, choose Configure > Service Settings.

    The Service Settings page is displayed.

    NOTE:

    If the iBMC version is earlier than 2.01, the Port Settings page is displayed.

  4. Enable HMM SSH NAT and set Port to 30022, as shown in Figure 4-10.
    Figure 4-10 Enabling the transparent transmission function

    Log in to the HMM CLI.

  5. On the client, double-click PuTTY.exe.

    The PuTTY Configuration window is displayed, as shown in Figure 4-11.

    Figure 4-11 PuTTY Configuration

  6. Set the login parameters.

    The parameters are described as follows:

    • Host Name (or IP address): Enter the IP address of the iBMC management network port on the server node, for example, 10.10.1.104.
    • Port: Retain the default value 30022.
    • Connection type: Retain the default value SSH.
    • Close window on exit: Retain the default value Only on clean exit.
    NOTE:

    After you set Host Name (or IP address) and then Saved Sessions and click Save, you can simply double-click the saved settings under Saved Sessions to log in to the server.

  7. Click Open.

    The PuTTY window is displayed. Then the message "login as:" is displayed, prompting you to enter a user name.

    NOTE:
    • If you log in to the server for the first time, the PuTTY Security Alert dialog box is displayed. If you trust this site, click Yes. The PuTTY window is displayed.
    • If the entered user name or password is incorrect during server login, PuTTY must be connected again.
  8. Enter the user name and password as prompted.
  9. Run the following command to check that Product Name is MM810, which indicates that the transparent transmission function is configured successfully.

    ipmcget -d version

    The command output is as follows:

    iBMC:/->ipmcget -d version 
    ------------------- iBMC INFO ------------------- 
    IPMC CPU: iBMC 
    IPMI Version: 2.0 
    CPLD Version: (U1036)0.05 
    Active iBMC Version: (U1)1.88 
    Active iBMC Built: 09:36:05 Sep 28 2015 
    Backup iBMC Version: 1.89 
    SDK Version: 1.57 
    SDK Built: 15:55:44 Sep 11 2015 
    Active Uboot Version: 1.1.35 (Mar 25 2015 - 10:24:41) 
    Backup Uboot Version: 1.1.35 (Mar 25 2015 - 10:24:41) 
    IPMB Address: 0x10 
    ----------------- Product INFO ----------------- 
    Product ID: 0x0003 
    Product Name: MM810 
    -------------- Mother Board INFO --------------- 
    Mainboard BoardID: 0x0065 
    Mainboard PCB: .B 
    -------------- Backplane INFO ------------------ 
    Backplane BoardID: 0x0044 
    Backplane PCB: .A     
Translation
Download
Updated: 2018-09-06

Document ID: EDOC1000066339

Views: 35986

Downloads: 1698

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next