No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

CX110 Switch Module V100R001C10 User Guide 10

This document describes the features, installation, removing, and configuration methods of the CX110 GE switch module of the E9000 server.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Logging In to the CLI of Each Switching Plane

Logging In to the CLI of Each Switching Plane

Log in to the GE switching plane CLI of the CX110 over Secure Shell (SSH), Serial Over LAN (SOL), or a serial port.

Log in to the CLI of the GE switching plane for the CX110 by using one of the following methods:

  • Over SSH: Remotely log in to the CLI of the GE switching plane over an Ethernet.
  • Over SOL: Log in to the serial port of the GE switching plane through the MM910 SOL screen.
  • Over a serial port: Connect a serial cable to the SYS serial port of the CX110 and log in to the CLI without using an IP address.

Prerequisites

Data

Table 4-4 Default Data

Name

Default Data

Login Method

GE switching plane

  • User name: root
  • Password: Huawei12#$

SSH

  • No user name
  • Password: Huawei12#$
  • Serial port
  • SOL

Tools

If you want to log in to a server CLI over a serial port, prepare the following hardware:

  • PC with an RS232 serial port
  • DB9-RJ45 cable

Procedure

  • Log in to the CLI of a switching plane over SSH.
  1. Connect the local PC to the MM910.

    • Connect the network port of the local PC to the MGMT port of the active or standby MM910.

      Figure 4-2 shows the network connections.

      Figure 4-2 Network connections

      If the MGMT port on the active MM910 is already connected with a network cable, do not remove the network cable from the MGMT port. Otherwise, an active/standby switchover of the MM910s will be triggered, which may cause network interruption.

      NOTE:

      The MM910 management port is provided by either of the following modes:

      • An Ethernet port on the switch module in slot 2X or 3X.

        However, if a CX910/CX911/CX912/CX913 is in slot 2X or 3X, only a GE port can be used; if a CX920 is in slot 2X or 3X, only a 10GE port can be used. The CX910/CX911/CX912/CX913 are not recommended for providing the management port of the management module.

      • MGMT port on the MM910 panel
      • For the MM910 (U54)2.25 or earlier, the management port is provided by the switch module by default. For the MM910 (U54)2.26 or later, the management port is provided by the MM910 by default. For details about how to query the MM910 version, see MM910 Management Module V100R001 User Guide.
      • You can run the outportmode command to change the mode in which the MM910 management port is provided. If the switch module in slot 2X or 3X is used to provide the management port, do not connect the MM910 MGMT port and the switch module ports to the same network. Otherwise, a network storm will occur and the network will be interrupted. For details, see MM910 Management Module V100R001 Command Reference.
    • Connect the network port of the local PC to the MGMT or STACK port of the active MM910.
      • If the MGMT port of the active MM910 is available, use this port. Figure 4-3 shows the connection.
        Figure 4-3 Connection between the local PC and the active MM910 (in slot MM2 in this example)
      • If the MGMT port of the active MM910 is unavailable, connect the PC to the STACK port of the active MM910. If the STACK port is used to stack the MGMT port in another chassis, connect the PC to an idle STACK port on an active MM910 in a chassis cascaded with the E9000 chassis. Figure 4-4 shows the connection.

        If the MGMT port on the active MM910 is already connected with a network cable, do not remove the network cable from the MGMT port. Otherwise, an active/standby switchover of the MM910s will be triggered, which may cause network interruption.

        Figure 4-4 Connection between the local PC and an idle STACK port on an MM910 stacked

  1. Use an SSH connection tool to connect to the IP address of a switching plane to log in to the CLI of the switching plane.

    This topic uses PuTTY as an example for login over SSH. For details, see Logging In to the MM910 CLI Over a Network Port by Using PuTTY.

  • Log in to the CLI of a switching plane over SOL.
  1. Connect the Ethernet port on the PC to the MGMT port on the active or standby MM910. For details, see 1 in "Log in to the CLI of a switching plane over SSH.".

    • If the MGMT port on the active MM910 is already connected with a network cable, do not remove the network cable from the MGMT port. Otherwise, an active/standby switchover of the MM910s will be triggered, which may cause network interruption.
    • If you want to connect your local PC directly to the MM910 using a network cable but the MGMT port on the active MM910 is already connected with a network cable, connect the network cable from the local PC to the STACK port of the active MM910 in the chassis. If the STACK port on the active MM910 is also used, connect the network cable to an idle STACK port on an active MM910 in a chassis cascaded with the E9000 chassis.

  2. Use an SSH connection tool to log in to the MM910 CLI by using the floating IP address of the MM910s.

    This topic describes how to use PuTTY to log in over SSH. For details, see Logging In to the MM910 CLI Over a Network Port by Using PuTTY.

  3. Log in to the CLI of a switching plane over MM910 SOL.

    For details, see Logging In to a Switch Module over MM910 SOL.

  • Log in to the CLI of a switching plane over a serial port.
  1. Use a DB9-RJ45 cable to connect the RS232 serial port of the PC to the SYS serial port on the CX110 panel.
  2. Use a serial port communication tool to log in to the CLI of a switching plane.

    Set the key communication parameters as follows:

    • Serial line to connect to: COMn
    • Data bits: 8
    • Stop bits: 1
    • Parity: None
    • Flow control: None
    NOTE:

    n indicates the serial port number and is an integer.

    In this document, PuTTY is used as an example for login over a serial port. For details, see Logging In to a Device Over a Serial Port by Using PuTTY.

Translation
Download
Updated: 2019-08-09

Document ID: EDOC1000068625

Views: 18722

Downloads: 487

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next