No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S12700 Series Agile Switches Hardware Installation and Maintenance Guide

This document describes hardware installation procedures of the S12700 series switches, troubleshooting methods for common hardware faults, and switch maintenance instructions.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Installing an S12712 Chassis

Installing an S12712 Chassis

Context

  • Do not block the air intake vent (on the left side) and air exhaust vent (at the rear) on the chassis. Leave 70 mm to 90 mm clearance to ensure effective heat dissipation.
  • Do not move or lift a switch by the top edges of the chassis as this may distort the chassis.
  • When installing a switch, ensure that the chassis bottom is completely attached to the guide rails or tray in the cabinet or rack.
NOTE:
  • Keep the tweezers delivered with the switch for future use.
  • Huawei offers expandable guide rails for the S12700 series switches. You can place an order if you need them.

  • If you use Huawei expandable guide rails to support the chassis, use the installation template to mark the installation position directly.
  • If you do not use Huawei expandable guide rails to support the chassis, cut off the installation template along the cutting line marked "S12712 (Huawei expandable guide rails not used)."
  • This section describes how to install an S12712 switch using expandable guide rails.

Tools and Accessories

  • Scissors
  • Flat-head screwdriver
  • Phillips screwdriver
  • Marker
  • Installation template
  • Floating nuts and matching screws
  • Guide rails and matching screws (separately purchased)

Procedure

  1. Install mounting brackets. Measure the distance a from the front mounting rails to the interior side of the front door (see Checking the Cabinet or Rack), and then install mounting brackets to the switch based on the mapping between distance a and mounting bracket installation positions.

    Table 7-3  Mapping between distance a and mounting bracket installation positions

    Distance a

    Mounting Bracket Installation Position

    68 mm

    See Figure 7-17.

    • 95 mm

    • 100 mm

    See Figure 7-18.

    193 mm

    See Figure 7-19.

    Figure 7-17  Mounting bracket installation position (a = 68 mm)
    Figure 7-18  Mounting bracket installation position (a = 95 mm or a = 100 mm)
    Figure 7-19  Mounting bracket installation position (a = 193 mm)

  2. Mark mounting holes on the mounting rails.
    1. Locate the 28 mounting holes to be used. Determine the chassis installation position in the cabinet, use the installation template to locate 28 mounting holes, and use a marker to mark these mounting holes. See Figure 7-20.

      NOTE:
      • When Huawei expandable guide rails are used, you can install the chassis at the bottom of the cabinet or a multiple of 1 U above the cabinet bottom. When Huawei expandable guide rails are not used, the installation height of the chassis must be a multiple of 1 U and larger than or equal to 1 U.

      • 1 U equals 1.75 inch (44.45 mm). U is a unit of height defined in International Electrotechnical Commission (IEC) 60297.

      Figure 7-20  Locating mounting holes

    2. Remove the installation template.
    3. Mark mounting holes for the guide rails on the rear mounting rails. Align the mounting holes on the rear mounting rails with those on the front mounting rails.
  3. Install the floating nuts and guide rails.
    1. Use a flat-head screwdriver to install 28 floating nuts in the marked mounting holes. See callout 1 in Figure 7-21.
    2. Install guide rails. Make the UP end of an expandable guide rail face up, hang the guide rail on the mounting rail by the hook on the guide rail, and then fix the guide rail with screws. See callout 2 in Figure 7-21. Install the other guide rail in the same way.

      If no guide rails are available, use a tray instead.

      Figure 7-21  Securing the guide rails

  4. Install the chassis in the cabinet.
    1. Three persons lift the chassis onto the guide rails from the front door, and then slowly push the chassis into the cabinet along the guide rails. See callout 1 in Figure 7-22.

      NOTE:

      While persons are pushing the chassis, another person can drag the chassis by using the handle at the rear of the chassis.

    2. Use screws to secure the chassis to the cabinet. See callout 2 in Figure 7-22.

    Figure 7-22  Installing the chassis in the cabinet

  5. Connect the ground cable.
Translation
Download
Updated: 2019-05-15

Document ID: EDOC1000069460

Views: 27623

Downloads: 817

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next