No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S12700 Series Agile Switches OSP Quick Start Quide

This document describes hardware installation and basic configuration of the OSP card.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Indicators and Ports

Indicators and Ports

Button and Indicator Description

Figure 1-2 shows the buttons and indicators on the OSP card panel.

Figure 1-2  Buttons and indicators on the OSP card panel

Table 1-4 describes the buttons and indicators on the OSP card panel.

Table 1-4  Buttons and indicators on the OSP card panel

Number

Indicator/Button

Color

Description

1

PWR button

-

Press for 0.5s to power on or off the card.

Hold down the button for more than 4s forcibly to power off the card. This operation is performed when the card stops responding.

2

RST button

-

Press this button to reset the operating system and application software on the card.

NOTICE:
Pressing this button causes loss of some service packets. Do not press the RST button unless necessary.

3

STAT

-

Off: The card is power off or is resetting.

Yellow

Steady on: The BIOS is running.

Green

Steady on: The operating system (OS) is running normally.

Red

Steady on: A major alarm has occurred and requires manual intervention. For example, hardware self-check fails or no OS is available.

4

ACT indicator of ETH port

Yellow

Blinking: The port is transmitting and receiving data.

5

LINK indicator of ETH port

Green

Steady on: A link has been established on the port.

6

HDD0 and HDD1 hard disk indicators

Green

Blinking: The hard disk is being accessed.

7

RUN/ALM: running status indicator

Green

Steady on: The card has been powered on, but the software is not running.

Slow blinking: The card software is running properly.

Fast blinking: The card software is starting.

Red

Steady on: The card has failed and the fault requires manual intervention.

Yellow

Steady on: The card is powered off. (For example, the card has been forcibly powered off using the power off command or is about to start.)

Port Description

Figure 1-3 shows the ports on the OSP card panel.

Figure 1-3  Ports on the OSP card panel

1 One console management port, connected to an operation terminal to implement on-site system configuration
2 One ETH management port (10M/100M/1000M BASE-T auto-sensing), connected to the network port of an operation terminal or network management workstation to set up a local or remote configuration environment
3 Two USB ports, connected to peripherals such as a USB mouse or keyboard
4 One VGA port, used to connect to a monitor
5 Two hard disk slots
ETH management port

You can connect a switch to a configuration terminal or network management workstation through the ETH management port to configure the switch onsite or remotely. The port must use an ethernet cable. Table 1-5 describes the attributes of an ETH management port.

Table 1-5  ETH management port attributes
Attribute Description
Connector type RJ45
Standards compliance IEEE802.3

Working mode

10/100/1000 Mbit/s auto-sensing

Full duplex

Maximum transmission distance

100 m

Console management port

The console management port is connected to an operation terminal or network management workstation for on-site configuration. The port must use a console cable. Table 1-6 describes the attributes of an console management port.

Table 1-6  Console management port attributes
Attribute Description
Connector type RJ45
Working mode Duplex Universal Asynchronous Receiver/Transmitter (UART)
Standards compliance RS232

Baud rate

9600 bit/s to 115200 bit/s

Default value: 9600 bit/s

Translation
Download
Updated: 2019-02-13

Document ID: EDOC1000069462

Views: 3554

Downloads: 231

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next