No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S12700 Series Agile Switches Typical Configuration Examples

This document provides examples for configuring features in typical usage scenarios.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Configuring Local Port Mirroring (1:1 Mirroring)

Example for Configuring Local Port Mirroring (1:1 Mirroring)

Local Port Mirroring Overview

In local port mirroring, an observing port is directly connected to a monitoring device and directly forwards the packets copied from a mirrored port to the monitoring device for fault location and service monitoring.

Configuration Notes

  • You must dedicate observing ports for mirroring use and do not configure other services on them to prevent mirrored traffic and other service traffic from affecting each other. Do not configure any member port of an Eth-Trunk as an observing port. If you must do so, ensure that the bandwidth of service traffic on this port and the bandwidth occupied by the mirrored traffic do not exceed the bandwidth limit of the port.

  • If the mirroring function is deployed on many ports of a device, a great deal of internal forwarding bandwidth will be occupied, which affects the forwarding of other services. Additionally, if the mirrored port bandwidth is higher than the observing port bandwidth, for example, 1000 Mbit/s on a mirrored port and 100 Mbit/s on an observing port, the observing port will fail to forward all mirrored packets in a timely manner because of insufficient bandwidth, leading to packet loss.

  • On all Huawei S series modular switch models, Eth-Trunks can be configured as observing ports.

  • Both physical interfaces and Eth-Trunks can be configured as mirrored ports. If an Eth-Trunk is configured as a mirrored port, its member ports cannot be configured as observing ports.

  • This configuration example applies to all switches running all versions.

Networking Requirements

As shown in Figure 17-7, the administrative department of a company accesses the Internet through the Switch, and the monitoring device Server is directly connected to the Switch.

Internet access traffic of the administrative department needs to be monitored through the Server.

Figure 17-7  Networking of local port mirroring

Configuration Roadmap

The configuration roadmap is as follows:
  1. Configure GE1/0/2 of the Switch as a local observing port to forward mirrored packets to the Server.
  2. Configure GE1/0/1 of the Switch as a mirrored port to copy Internet access traffic of the administrative department to the local observing port.

Procedure

  1. Configure an observing port.

    # Configure GE1/0/2 of the Switch as a local observing port.

    <HUAWEI> system-view
    [HUAWEI] sysname Switch
    [Switch] observe-port 1 interface gigabitethernet 1/0/2     //Configure GE1/0/2 as a local observing port 1.
    

  2. Configure a mirrored port.

    # Configure GE1/0/1 of the Switch as a mirrored port to copy the packets received by the mirrored port to the local observing port.

    [Switch] interface gigabitethernet 1/0/1
    [Switch-GigabitEthernet1/0/1] port-mirroring to observe-port 1 inbound     //Mirror incoming packets on GE1/0/1 to observing port 1.
    [Switch-GigabitEthernet1/0/1] return
    

  3. Verify the configuration.

    # Check the observing port configuration.

    <Switch> display observe-port
      ----------------------------------------------------------------------
      Index          : 1
      Untag-packet   : No
      Interface      : GigabitEthernet1/0/2
      ----------------------------------------------------------------------
    

    # Check the mirrored port configuration.

    <Switch> display port-mirroring
      ----------------------------------------------------------------------
      Observe-port 1 : GigabitEthernet1/0/2
      ----------------------------------------------------------------------
      Port-mirror:
      ----------------------------------------------------------------------
           Mirror-port               Direction  Observe-port
      ----------------------------------------------------------------------
      1    GigabitEthernet1/0/1      Inbound    Observe-port 1
      ----------------------------------------------------------------------
    

Configuration Files

  • Configuration file of the Switch

    #
    sysname Switch
    #
    observe-port 1 interface GigabitEthernet1/0/2
    #
    interface GigabitEthernet1/0/1
     port-mirroring to observe-port 1 inbound
    #
    return
    
Download
Updated: 2019-05-16

Document ID: EDOC1000069466

Views: 245119

Downloads: 1972

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next