No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S2700, S3700, S5700, S6700, S7700, and S9700 Series Switches Typical Configuration Examples

This document provides examples for configuring features in typical usage scenarios.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Setting Up a Stack Using Service Ports (V200R001 to V200R002)

Example for Setting Up a Stack Using Service Ports (V200R001 to V200R002)

Overview

Service port connection allows member switches to be connected using service ports, without requiring dedicated stack cards.

To improve stack efficiency and reduce manual configuration, since V200R011C10, switches can set up a stack using dedicated stack cables. Service port connections are classified into ordinary and dedicated cable connections based on cable types.
  • Ordinary cable connection: Switches use optical cables, network cables, and high-speed cables to set up a stack.

  • Dedicated cable connection: Switches use dedicated stack cables to set up a stack. The two ends of a dedicated stack cable are the master end with the Master tag and the slave end without any tag.

Networking Requirements

A new enterprise network needs to provide sufficient ports for access devices, and the network structure should be simple to facilitate configuration and management.

As shown in Figure 5-11, SwitchA, SwitchB, and SwitchC need to set up a stack in a ring topology and connect to SwitchD through an inter-device Eth-Trunk. SwitchA, SwitchB, and SwitchC are the master, standby, and slave switches respectively, with stack IDs of 0, 1, and 2 and stack priorities of 200, 100, and 100. As the three switches function as one logical device on the network, the number of ports is increased and network management and maintenance are simplified.

In this example, S5700LIs set up a stack.

Figure 5-11  Stack networking

Configuration Roadmap

  1. Configure logical stack ports and add physical member ports to the corresponding logical stack ports to enable packet forwarding between member switches.

  2. Configure stack IDs and stack priorities for member switches to facilitate device management and identification.

  3. Power off SwitchA, SwitchB, and SwitchC, connect physical member ports using SFP+ stack cables, and then power on the three switches.

  4. Configure an inter-device Eth-Trunk to increase reliability and uplink bandwidth.

  5. Configure dual-active detection (DAD) in relay mode to ensure network availability when the stack splits.

Procedure

  1. Configure logical stack ports and add physical member ports to them.

    NOTE:

    Interface stack-port 0/1 of one switch must be connected to interface stack-port 0/2 of another switch. Otherwise, the stack cannot be set up.

    # Configure service ports GigabitEthernet0/0/27 and GigabitEthernet0/0/28 on SwitchA as physical member ports and add them to corresponding logical stack ports.

    <HUAWEI> system-view
    [HUAWEI] sysname SwitchA
    [SwitchA] stack port interface gigabitethernet 0/0/27 enable
    [SwitchA] stack port interface gigabitethernet 0/0/28 enable
    [SwitchA] interface stack-port 0/1
    [SwitchA-stack-port0/1] port member-group interface gigabitethernet 0/0/27
    [SwitchA-stack-port0/1] quit
    [SwitchA] interface stack-port 0/2
    [SwitchA-stack-port0/2] port member-group interface gigabitethernet 0/0/28
    [SwitchA-stack-port0/2] quit
    

    # Configure service ports GigabitEthernet0/0/27 and GigabitEthernet0/0/28 on SwitchB as physical member ports and add them to corresponding logical stack ports.

    <HUAWEI> system-view
    [HUAWEI] sysname SwitchB
    [SwitchB] stack port interface gigabitethernet 0/0/27 enable
    [SwitchB] stack port interface gigabitethernet 0/0/28 enable
    [SwitchB] interface stack-port 0/1
    [SwitchB-stack-port0/1] port member-group interface gigabitethernet 0/0/27
    [SwitchB-stack-port0/1] quit
    [SwitchB] interface stack-port 0/2
    [SwitchB-stack-port0/2] port member-group interface gigabitethernet 0/0/28
    [SwitchB-stack-port0/2] quit
    

    # Configure service ports GigabitEthernet0/0/27 and GigabitEthernet0/0/28 on SwitchC as physical member ports and add them to corresponding logical stack ports.

    <HUAWEI> system-view
    [HUAWEI] sysname SwitchC
    [SwitchC] stack port interface gigabitethernet 0/0/27 enable
    [SwitchC] stack port interface gigabitethernet 0/0/28 enable
    [SwitchC] interface stack-port 0/1
    [SwitchC-stack-port0/1] port member-group interface gigabitethernet 0/0/27
    [SwitchC-stack-port0/1] quit
    [SwitchC] interface stack-port 0/2
    [SwitchC-stack-port0/2] port member-group interface gigabitethernet 0/0/28
    [SwitchC-stack-port0/2] quit
    

  2. Configure stack IDs and stack priorities. The default stack ID is 0, and the default stack priority is 100.

    [SwitchA] stack slot 0 priority 200     //Set the stack priority of the master switch to 200, which is larger than those of other member switches, and use the default stack ID 0.
    [SwitchB] stack slot 0 renumber 1       //Use the default stack priority 100 and set the stack ID to 1.
    [SwitchC] stack slot 0 renumber 2       //Use the default stack priority 100 and set the stack ID to 2.

  3. Turn off power supplies of SwitchA, SwitchB, and SwitchC, connect physical member ports using SFP+ stack cables as shown in Figure 5-12, and then power on the three switches.

    Figure 5-12  Stack connection

  4. Check whether a stack is set up successfully.

    # Check the stack indicator status.

    Press the MODE button on any member switch to change the mode status indicator to the stack mode.

    • If the mode status indicators on all the member switches change to the stack mode, the stack is set up successfully.
    • If the mode status indicator on any member switch does not change to the stack mode, the stack is not set up.
    NOTE:
    • The S6700EI uses the mode status indicator to show the stack and speed modes. After you press the MODE button, the indicator is steady red and off after 45 seconds, indicating that the switch enters the stack mode.
    • The S5700-LI and S5710-EI have an independent stack mode indicator (STCK indicator). After you press the MODE button, the indicator is steady green or blinking and off after 45 seconds, indicating that the switch enters the stack mode.

    # Check basic stack information.

    Log in to the stack to check whether the number of member switches in the stack is the same as the actual value and whether the stack topology is the same as the actual hardware connection.

    <SwitchA> system-view
    [SwitchA] sysname Stack
    [Stack] display stack
    Stack topology type : Ring
    Stack system MAC: 0018-82d2-2e85
    MAC switch delay time: 10 min
    Stack reserved vlanid : 4093
    Slot     Role        Mac address      Priority   Device type
    -------------------------------------------------------------
        0     Master      0018-82d2-2e85   200        S5700-28P-LI-AC
        1     Standby     0018-82c6-1f44   100        S5700-28P-LI-AC
        2     Slave       0018-82c6-1f4c   100        S5700-28P-LI-AC

  5. Configure an inter-device Eth-Trunk.

    # Create an Eth-Trunk in the stack and configure uplink physical ports as Eth-Trunk member ports.

    [Stack] interface eth-trunk 10
    [Stack-Eth-Trunk10] trunkport gigabitethernet 0/0/5
    [Stack-Eth-Trunk10] trunkport gigabitethernet 1/0/5
    [Stack-Eth-Trunk10] trunkport gigabitethernet 2/0/5
    [Stack-Eth-Trunk10] quit

    # Create an Eth-Trunk on SwitchD and configure the ports connected to the stack as Eth-Trunk member ports.

    <HUAWEI> system-view
    [HUAWEI] sysname SwitchD
    [SwitchD] interface eth-trunk 10
    [SwitchD-Eth-Trunk10] trunkport gigabitethernet 0/0/1
    [SwitchD-Eth-Trunk10] trunkport gigabitethernet 0/0/2
    [SwitchD-Eth-Trunk10] trunkport gigabitethernet 0/0/3
    [SwitchD-Eth-Trunk10] quit

  6. Verify the Eth-Trunk configuration.

    # Check Eth-Trunk member port information. The following displays information about Eth-Trunk member ports in the stack.
    [Stack] display trunkmembership eth-trunk 10
    Trunk ID: 10
    Used status: VALID
    TYPE: ethernet
    Working Mode : Normal
    Number Of Ports in Trunk = 3
    Number Of Up Ports in Trunk = 3
    Operate status: up
    
    Interface GigabitEthernet0/0/5, valid, operate up, weight=1
    Interface GigabitEthernet1/0/5, valid, operate up, weight=1
    Interface GigabitEthernet2/0/5, valid, operate up, weight=1

  7. Configure DAD in relay mode on SwitchD and configure SwitchD as the relay agent.

    # In the stack, configure DAD in relay mode on the inter-device Eth-Trunk.

    [Stack] interface eth-trunk 10
    [Stack-Eth-Trunk10] dual-active detect mode relay
    [Stack-Eth-Trunk10] return

    # On SwitchD, configure DAD in relay mode on the Eth-Trunk.

    [SwitchD] interface eth-trunk 10
    [SwitchD-Eth-Trunk10] dual-active relay
    [SwitchD-Eth-Trunk10] return

  8. Verify the DAD configuration.

    # Check the DAD configuration of the stack.

    <Stack> display dual-active verbose
    Current DAD status: Detect                                                      
    Dual-active direct detect interfaces configured:                                
    Dual-active relay detect interfaces configured:                                 
     Eth-Trunk10
    Excluded ports(configurable):                                                   
    Excluded ports(can not be configured): 
     GigabitEthernet0/0/27                                          
     GigabitEthernet0/0/28
     GigabitEthernet1/0/27                                          
     GigabitEthernet1/0/28                                          
     GigabitEthernet2/0/27                                          
     GigabitEthernet2/0/28 
    

    # Check the DAD proxy configuration on SwitchD.

    <SwitchD> display dual-active proxy
    Dual-active relay interfaces configured:
     Eth-Trunk10

Configuration Files

  • Stack configuration file (the stack configuration is written to the flash memory instead of the configuration file)

    #
    sysname Stack
    #
    interface Eth-Trunk10
     dual-active detect mode relay
    #
    interface GigabitEthernet0/0/5
     eth-trunk 10
    #
    interface GigabitEthernet1/0/5
     eth-trunk 10
    #
    interface GigabitEthernet2/0/5
     eth-trunk 10
    #
    return
  • SwitchD configuration file

    #
    sysname SwitchD
    #
    interface Eth-Trunk10
     dual-active relay
    #
    interface GigabitEthernet0/0/1
     eth-trunk 10
    #
    interface GigabitEthernet0/0/2
     eth-trunk 10
    #
    interface GigabitEthernet0/0/3
     eth-trunk 10
    #
    return
Download
Updated: 2019-04-20

Document ID: EDOC1000069520

Views: 664816

Downloads: 29859

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next