No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S9300, S9300E, and S9300X Series Switches Hardware Installation and Component Replacement

This document describes hardware installation procedures of the S9300, S9300E, and S9300X series switches, troubleshooting methods for common hardware faults, and switch maintenance instructions.

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Preparing Installation Tools and Accessories

Preparing Installation Tools and Accessories

Table 5-23 lists the tools required for installing a switch.

Table 5-23 Installation tools

Tool

Description

Picture

Protective gloves

Used to protect hands during operation.

ESD gloves

Used to prevent electrostatic discharges.

ESD wrist strap

Used to prevent electrostatic discharges. Wear the strap on your wrist and insert the other end into the ESD jack on the cabinet.

Utility knife

Used to cut cartons or paper.

Scissors

Used to cut the installation template.

Tweezers

Used to remove optical fibers or network cables.

Measuring tape

Used to measure distances.

Marker

Used to mark component installation positions.

Flat-head screwdriver

Used to turn slotted-head screws and bolts.

Phillips screwdriver

Used to turn cross-head screws and bolts.

Diagonal pliers

Used to cut insulation tubes and cable ties.

Adjustable wrench

Used to tighten or loosen hex or square bolts and nuts. The span can be adjusted to suit bolts or nuts in different sizes.

Needle-nose pliers

Used to raise locking bars on a crate.

Network cable tester

Used to test network cable connectivity.

Multimeter

Used to test cabinet insulation, cable connectivity, and device electrical performance indicators, including voltage, current, and resistance.

Table 5-24 lists the installation accessories required for installing a switch.

Table 5-24 Installation accessories

Tool

Description

Picture

Insulation tape

Used to insulate power wires or other conductors.

Corrugated pipe

Used to protect optical fibers.

Table 5-25 lists the installation accessories delivered with a switch.

Table 5-25 Installation accessories

Accessory

Quantity

Description

Part Number

Cable tie (150 x 3.6 mm)

50

Used to bundle cables.

21100015

Cable tie (300 x 3.6 mm)

50

Used to bundle cables.

21100144

Tweezers

1 pair

Used to install or remove optical fibers on optical ports.

63120166

Signal cable label

5

Used to identify locations of signal cables.

29041060

Power cable label

1

Used to identify the location of the power cable.

29041061

ESD wrist strap

1

Prevents ESD damages when you touch or operate the equipment or components.

28050001

Fiber binding tape

1 m

Used to bundle optical fibers.

21101258

Serial cable

1

Used to connect the console port of the switch to a serial port of a maintenance terminal for local commissioning or maintenance of the switch.

04051113

Ground cable

1

Used to ground the switch.

04046941

Removable handle

2

NOTE:

The S9303, S9303E, and S9300X-12 switches do not have removable handles.

Used to move the switch.

  • S9306, S9306E, S9312, S9312E, S9310, and S9310X: 21240209
  • S9300X-4 and S9300X-8: 21240406

Panel screw (M6X12)

  • S9303, S9303E: 8
  • S9306, S9306E: 12
  • S9310, S9310X, S9312, S9312E: 15

Used to fix the switch.

26020141

Floating nut (M6)

  • S9303, S9303E: 8
  • S9306, S9306E: 12
  • S9310, S9310X, S9312, S9312E: 15

Installed on mounting rails of a cabinet/rack and used with M6 screws to secure the switch in the cabinet/rack.

26020075

Quick Installation Guide

1

Used to guide equipment installation.

  • S9300 and S9300E: 31507799
  • S9310: 31507887
  • S9310X: 31507935
  • S9300X-4, S9300X-8, and S9300X-12: 31500BNV

Cable management frame

1

Install on the switch to route cables.

  • S9300X-4: 21123608
  • S9300X-8: 21212340
  • S9300X-12: 21212341

Warranty card

1

Warranty of repair service.

31110018

Open Source Software Notice

1

NOTE:

Only the S9300X-4, S9300X-8, and S9300X-12 switches have open source software notice.

Declaration on use of open source software.

31070662

Translation
Download
Updated: 2019-11-30

Document ID: EDOC1000069582

Views: 28291

Downloads: 463

Average rating:
This Document Applies to these Products

Related Version

Related Documents

Share
Previous Next