No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S9300, S9300E, and S9300X Series Switches Hardware Installation and Maintenance Guide

This document describes hardware installation procedures of the S9300, S9300E, and S9300X series switches, troubleshooting methods for common hardware faults, and switch maintenance instructions.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
S9310 Clustering Using CSS Cards

S9310 Clustering Using CSS Cards

Context

S9310 switches can set up a cluster using the CSS cards integrated on LE1D2SRUKC00, LE1D2SRUKC01 SRUs or LE1D2SFUK000, LSS3SFUKA200 SFUs. You do not need to install the CSS cards in this mode.

Each chassis can have only one SRU installed. It is recommended that each chassis have two SRUs installed. If 1+N backup of SRUs is required so that a CSS can operate normally even if two SRUs in one chassis are faulty, SFUs also need to be installed.

  • When installing a copper cable, optical module, or optical fiber, you can determine that it has been installed properly after hearing a click.
  • When removing a copper cable, optical module, or optical fiber, push its connector or handle slightly and then pull it out.
  • Ensure that the bend radius of the copper cables or optical fibers is greater than the minimum bend rand required. For more information, see the Hardware Description.

Tools and Accessories

  • ESD wrist strap or ESD gloves
  • Phillips screwdriver
  • Diagonal pliers
  • Cable ties
  • Labels

Procedure

  1. Wear an ESD wrist strap or ESD gloves. When wearing an ESD wrist strap, ensure that the ESD wrist strap is in a close contact with your wrist, and insert the other end in the ESD jack of a cabinet/rack.
  2. Install the SRU and SFU, as shown in Installing a Card.
  3. Attach number labels on both ends of the cluster cables.
  4. Connect the stack ports with cluster cables.
    • 4*10GE ports (The following example uses chassis with only one SRU and one SFU)

    • 40GE ports (The following example uses chassis with only one SRU and one SFU)

    NOTE:
    • Follow these rules when connecting S9310 integrated CSS cards:
      • On the S9310, the local and peer chassis can be connected using either SRUs or SFUs or both SRUs and SFUs. SRUs or SFUs in one chassis can only be connected to the same type of cards (SRUs or SFUs) in the other chassis.
      • SRU-integrated and SFU-integrated CSS cards have two types of ports: 4*10GE ports and 40GE port. 10GE ports with the same port number must be connected, as shown in the preceding figure. For example, port 1 in blue on the left chassis must be connected to port 1 in blue on the right chassis.
      • The two chassis can set up a CSS as long as they are connected by one cluster cable. To ensure reliability, it is recommended that each SRU or SFU be connected using at least two cluster cables.
      • To support 1+N SRU backup, ensure that SFUs are connected using cluster cables.
    • To connect the stack ports with optical fibers, install optical modules on the stack ports, and then connect optical fibers to the optical modules.
    • To connect the stack ports with copper cables, directly connect the copper cables to the stack ports.

  5. Arrange the cables, route the cables through cable management frames, and bundle them with cable ties.

    NOTE:

    Keep the cable ties used to bundle cables on the same horizontal plane as the SFP+ or QSFP+ ports to reduce the impact of gravity on these ports.

  6. (Optional) Wrap redundant cables in cable management trays.

  7. Check the LINK indicator on the service cards. If the indicator is steady green, the ports are correctly connected.

    To power on the switches, ensure that power cables and ground cables are correctly connected and then switch on the external power modules and built-in power modules in turn.

Translation
Download
Updated: 2019-05-16

Document ID: EDOC1000069582

Views: 18106

Downloads: 417

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next