No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Web-based Typical Configuration Examples

AR100, AR120, AR150, AR160, AR200, AR1200, AR2200, AR3200, and AR3600

This document provides examples for configuring AR router features in typical usage scenarios.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Configuring Basic WLAN AC Services(V200R008 And Later Versions)

Example for Configuring Basic WLAN AC Services(V200R008 And Later Versions)

Specifications

This example only applies to the AR models that support the web system of the EasyOperation edition in V200R008C00 and later versions.

Only AR100&AR120&AR150&AR160&AR200 support the web system of the EasyOperation edition.

The AR109, AR109W, and AR109GW-L on the EasyOperation web platform do not support the WLAN AC function. Therefore, the WLAN AC function cannot be configured for these models on the EasyOperation web platform.

Networking Requirements

As shown in Figure 7-4, the AP is directly connected to the AC. An enterprise branch needs to deploy basic WLAN services for mobile office so that enterprise employees can access the enterprise internal network anywhere, anytime.

The requirements are as follows:
  • A WLAN named wlan-net is available.
  • Enterprise employees are assigned IP addresses on 10.10.11.0/24.
Figure 7-4  Networking diagram for configuring basic WLAN AC services

Procedure

  1. Configure GE0/0/0 connected to the AP.

    1. Choose Configuration > Configuration Wizard. The Configuration Wizard page is displayed, as shown in Figure 7-5.

      Figure 7-5  Configuration wizard

    2. Click Wireless Configuration Wizard. The Select Interface and Assign Addresses page is displayed, as shown in Figure 7-6. Select GE0/0/0 to be connected to the AP, and configure its IP address.

      Figure 7-6  Select Interface and Assign Addresses page

      NOTE:

      If you select Connect to AP on the Select Interface and Assign Addresses page, you do not need to manually create a management VLAN or VLANIF. The device automatically generates VLAN 888 as the management VLAN, creates VLANIF 888, and assigns 10.10.10.1 to VLANIF 888.

      Currently, only Layer 2 interfaces can be selected, but Layer 3 interfaces cannot be selected.

    3. Click Next. The Configure AC page is displayed.

  2. Configure the AP authentication mode and add an AP offline.

    1. On the Configure AC page shown in Figure 7-7, configure the country code and AP authentication mode.
      Figure 7-7  Configure AC page

    2. Set AP authentication mode to MAC. Click Add AP Offline. The Add AP Offline page is displayed, as shown in Figure 7-8. Set AP parameters as required.
      Figure 7-8  Add AP Offline page

    3. Click Finish. The Configure AC page is displayed.
    4. Click Next. The Check AP Login page is displayed.

  3. Check the AP login status.

    1. On the Check AP Login page shown in Figure 7-9, Status of the AP is normal, indicating AP login success.
      Figure 7-9  Check AP Login page

    2. Click Next. The Configure WLAN Service page is displayed.

  4. Configure WLAN services.

    1. On the Configure WLAN Service page shown in Figure 7-10, click Create. The Create SSID page is displayed.
      Figure 7-10  Configure WLAN Service page

    2. On the Create SSID page shown in Figure 7-11, set SSID parameters. Set SSID to wlan-net, Security policy to WPA-WPA2, and Password to a1234567.
      Figure 7-11  Create SSID page

      NOTE:
      If you select Connect to AP on the Select Interface and Assign Addresses page, you do not need to manually create a service VLAN or VLANIF. The device automatically generates VLAN 889 as the service VLAN, creates VLANIF 889, and assigns 10.10.11.1 to VLANIF 889.
    3. Click Finish. The Configure WLAN Service page is displayed, where you can find the new SSID, as shown in Figure 7-12.
      Figure 7-12  New SSID

    4. Click Finish to complete basic WLAN service configuration.

  5. Verify the configuration.

    The WLAN with the SSID wlan-net is available. After the password a1234567 is entered, STAs can connect to the WLAN.

Translation
Download
Updated: 2019-05-20

Document ID: EDOC1000079722

Views: 51077

Downloads: 7459

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next