No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

5288 V3 Server V100R003 User Guide 26

This document describes the features, appearance, and technical specifications of the 5288 V3 server, and how to install, power on, and power off the 5288 V3 server, connect cables, and install an operating system (OS) for it.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Installing the Server on Holding Rails

Installing the Server on Holding Rails

Holding rails apply to the cabinet where the distance between the front and rear mounting bars is 609 mm (23.98 in.) to 914 mm (35.98 in.).

When installing the RH5288 V3 on the holding rails, you can configure a cable management arm (CMA) to arrange the external cables connected to the server.

Procedure

  1. Install the front end and rear end of the holding rail.

    1. Holding down the release latch at the front end of the holding rail, pull out the locking plate by its hook. See steps (1) and (2) in Figure 3-11.
      Figure 3-11 Installing the front and rear ends of a holding rail

    2. Insert the positioning pins on the rear end of the holding rail into the square holes in the cabinet. See step (3) in Figure 3-11.
    3. Align the front end of the holding rail with the hole in the column, and push the holding rail forward to insert it into the hole in the column. See step (4) in Figure 3-11.
    4. Push the hook backwards to make the metal sheet in full contact with the column. See step (5) in Figure 3-11.
    5. (Optional) Install an M6 screw in the third square hole on the rear end of the holding rail to secure the rail. See step (6) in Figure 3-11.
    6. Install the other guide rail on the opposite side using the same method.

  2. Install the server.

    1. Pull out an inner rail from a holding rail until the inner rail cannot move, push the release button upward, and remove the inner rail from the holding rail. See steps (1) and (2) in Figure 3-12.
      Figure 3-12 Removing an inner rail

    2. Align the screws on the server with the notches in the inner guide rails, push the server forward until you hear a sound, and ensure that the latches eject and completely block the screws to fix the server to the inner guide rails. See Figure 3-13.
      Figure 3-13 Installing an inner rail

    3. Check that the buckles on the support trays are properly secured and the support trays touch the fixing blocks of the middle rails. See Figure 3-14. If the support trays are not in such a position, manually adjust them. Otherwise, the rolling balls may fall.
      Figure 3-14 Securing a support tray

    4. Lift the server, align the inner rails with the holding rails, and push the server into the cabinet. See Figure 3-15.
      NOTE:

      At least four persons are required to lift the server.

      Figure 3-15 Installing a server on holding rails

      NOTE:
      • Ensure that the inner rail is clipped into the middle rail, and then slowly push the chassis inside until you hear a click, as shown in (1) in Figure 3-16.
      • If the inner rail is not clipped into the middle rail, the rolling balls and the holding rail may be damaged as shown in (2) and (3) in Figure 3-16.
      Figure 3-16 Clipping the inner rail into the middle rail

    5. Press the release buttons on both sides, and push the server into the cabinet until the server cannot move forward. See Figure 3-17.
      Figure 3-17 Pushing a server into a cabinet

    6. Tighten the captive screws on the mounting ears to secure the server. See Figure 3-18.
    Figure 3-18 Securing a server

  3. Connect a network cable, a VGA cable, or USB devices as required, and connect power cables.
  4. (Optional) Install the cable management arm (CMA).

    1. Slot left outer arm of the support lever between the protrusions of the left outer rail. See step (1) in Figure 3-19.
      Figure 3-19 Installing the CMA

    2. Slot the right outer arm of the CMA between the protrusions of the right outer rail. See step (2) in Figure 3-19.
    3. Slot the right inner arm of the CMA between the protrusions of the right inner rail. See step (3) in Figure 3-19.

  5. (Optional) If a CMA is installed, the external cables connected to the server must be routed into the CMA. See Figure 3-20.

    Figure 3-20 CMA cabling

  6. Power on the 5288 V3.
Translation
Download
Updated: 2018-11-26

Document ID: EDOC1000080031

Views: 125667

Downloads: 2333

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next