No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Parts Replacement 12

OceanStor 18500 V3 and 18800 V3 Mission Critical Storage System V300R003

This document describes the procedure for replacing the parts of storage system in terms of safety operations, preparations, and precautions.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Replacing a BBU

Replacing a BBU

This section describes how to replace a BBU.

Impact on the System

  • Replacing a BBU affects data integrity.
  • During the replacement, if all other BBUs fail, the system is no longer BBU-protected. To enhance data integrity, the system forcibly implements LUN write through, and the system performance is compromised.

Prerequisites

  • A replacement BBU is ready.
  • Configuration data has been backed up.
  • The BBU that you want to replace has been located.
    NOTE:
    You can locate a component in either of the following ways:
    • Log in to DeviceManager, and go to the System page. On the System page, check the device view and locate the position of the component to be replaced. If the component has a location indicator, turn on the indicator. (For details about how to turn on a location indicator, see the online help of DeviceManager.)
    • Use the alarm indicator of the component to locate its component.

Precaution

  • Remove and insert a BBU with even force. Excessive force may damage the appearance or connectors of the BBU.
  • Remove only one BBU at a time.
  • When a BBU is being replaced, the storage system does not have BBU redundancy. Therefore, you are advised to replace a BBU as quickly as possible.
  • A BBU must be replaced within five minutes. Otherwise, the system heat dissipation is compromised.

Tools and Materials

  • ESD wrist strap
  • ESD bag
  • Labels

Procedure

  1. Check system status before replacement.
    1. Perform a system status inspection.

      Start SmartKit. On the homepage, choose MyTools > Storage > Parts Replacement > Inspection. The Inspection Wizard step 5-1:Welcome page is displayed after you go to the Inspection page. On the wizard, select Routine inspection and perform the inspection as instructed by the wizard.

      For details, you can click .

      NOTE:

      If some items fail the inspection, rectify the faults by performing the recommended actions in the inspection reports. Ensure that all other parts except the parts to be replaced are working correctly.

    2. Perform a pre-replacement inspection.

      On the homepage, choose MyTools > Storage > Parts Replacement > FRU Replacement. On the FRU Replacement page, select the part that you want to replace and perform the pre-replacement inspection as prompted. For details, see Using SmartKit for Parts Replacement (Recommended).

      You can proceed to next step only when all items pass the pre-replacement check and the replacement page is displayed. If any item fails, rectify the fault by taking recommended actions in the inspection reports.

  2. Wear an ESD wrist strap.
  3. Press the latch on the BBU to release the handle and pull out the BBU, as shown in Figure 4-20.

    Figure 4-20  Removing a BBU

  4. Place the removed BBU into an ESD bag.
  5. Take the replacement BBU out of its ESD bag.
  6. Fully open the handle of the replacement BBU, insert the BBU into the empty slot, and close the handle, as shown in Figure 4-21.

    Figure 4-21  Installing a BBU

  7. Wait about one minute and check the status of the Running/Alarm indicator on the BBU to determine whether the BBU is successfully installed. Figure 4-22 shows the location of the Running/Alarm indicator.

    • If the indicator is steady green or blinking green, the BBU is successfully installed.
    • If the indicator is steady red or off, the newly installed BBU is faulty, the BBU slot is faulty, or the BBU is incorrectly installed.
    Figure 4-22  Running/Alarm indicator on a BBU

  8. Confirm the replacement.
    1. Perform a post-replacement inspection.

      After the replacement, on the SmartKit page, click Replaced. Perform the post-replacement inspection as prompted.

    2. Check the system status after the replacement.

      Check the system status again on the Inspection page after the replacement. If any inspection item fails, rectify the fault based on the suggestions.

    3. Check services on a host for any storage-related error.

Follow-up Procedure

After the BBU is replaced, label it to facilitate subsequent operations.

Translation
Download
Updated: 2019-05-15

Document ID: EDOC1000084105

Views: 23994

Downloads: 143

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next