No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Parts Replacement 12

OceanStor 18500 V3 and 18800 V3 Mission Critical Storage System V300R003

This document describes the procedure for replacing the parts of storage system in terms of safety operations, preparations, and precautions.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Replacing a Power Module

Replacing a Power Module

This section describes how to replace a power module.

Impact on the System

During the replacement of a power module, if the redundant power module fails, the corresponding disk enclosures are unexpectedly powered off, causing all services in the disk enclosures to be interrupted and the system reliability to degrade.

Prerequisites

  • The replacement power module is ready.
  • The power module that you want to replace has been located.
    NOTE:
    You can locate a component in either of the following ways:
    • Log in to DeviceManager, and go to the System page. On the System page, check the device view and locate the position of the component to be replaced. If the component has a location indicator, turn on the indicator. (For details about how to turn on a location indicator, see the online help of DeviceManager.)
    • Use the alarm indicator of the component to locate its component.

Precaution

  • Do not touch the connectors of a power module and a power cable.
  • Remove and insert a power module with even force. Excessive force may damage the appearance or connectors of the power module.
  • Remove only one power module at a time.
  • A power module must be replaced within three minutes. Otherwise, the system heat dissipation is compromised.

Tools and Materials

  • ESD wrist strap
  • ESD bag
  • Label

Procedure

  1. Check system status before replacement.
    1. Perform a system status inspection.

      Start SmartKit. On the homepage, choose MyTools > Storage > Parts Replacement > Inspection. The Inspection Wizard step 5-1:Welcome page is displayed after you go to the Inspection page. On the wizard, select Routine inspection and perform the inspection as instructed by the wizard.

      For details, you can click .

      NOTE:

      If some items fail the inspection, rectify the faults by performing the recommended actions in the inspection reports. Ensure that all other parts except the parts to be replaced are working correctly.

    2. Perform a pre-replacement inspection.

      On the homepage, choose MyTools > Storage > Parts Replacement > FRU Replacement. On the FRU Replacement page, select the part that you want to replace and perform the pre-replacement inspection as prompted. For details, see Using SmartKit for Parts Replacement (Recommended).

      You can proceed to next step only when all items pass the pre-replacement check and the replacement page is displayed. If any item fails, rectify the fault by taking recommended actions in the inspection reports.

  2. Wear an ESD wrist strap.
  3. Remove the power cable.

    1. Loosen the retention clip, as shown in step 1 in Figure 5-4.
      Figure 5-4  Remove the AC power cable

    2. Pull up the retention clip, as shown in a of step 2 in Figure 5-4.
    3. Remove the AC power cable, as shown in b of step 2 in Figure 5-4.

  4. Press the latch on the power module to release the handle and pull out the power module, as shown in Figure 5-5.

    Figure 5-5  Removing a power module

  5. Put the removed power module into an ESD bag.
  6. Take the replacement power module out of its ESD bag.
  7. Open the handle of the replacement power module, insert the power module into the empty slot, and close the handle, as shown in Figure 5-6.

    Figure 5-6  Installing a power module

  8. Connect the power cable and secure it to the power socket.

    1. Press the locker of the retention clip outwards (as shown in a of step 1 in Figure 5-7), and meanwhile slide the retention clip to the connection part of the AC power cable (as shown in b of step 1 in Figure 5-7).
      Figure 5-7  Securing the AC power cables with retention clips

    2. Loosen the retention clip, as shown in step 2 in Figure 5-7.
    3. Press the retention clip inwards to secure the connection part of the AC power cable, as shown in step 3 in Figure 5-7.
      NOTE:

      Adjust the retention clip to ensure that it holds the AC power cable tightly.

  9. Wait about two minutes and check the status of the Running/Alarm indicator on the power module to determine whether the power module is successfully installed. Figure 5-8 shows the location of the Running/Alarm indicator.

    • If the indicator is steady green, the power module is successfully installed.
    • If the indicator is blinking green, the power input is normal but the disk enclosure is powered off.
    • If the indicator is steady red or off, the newly installed power module is faulty or the power module slot is faulty.
    Figure 5-8  Running/Alarm indicator on a power module

  10. Confirm the replacement.
    1. Perform a post-replacement inspection.

      After the replacement, on the SmartKit page, click Replaced. Perform the post-replacement inspection as prompted.

    2. Check the system status after the replacement.

      Check the system status again on the Inspection page after the replacement. If any inspection item fails, rectify the fault based on the suggestions.

    3. Check services on a host for any storage-related error.

Follow-up Procedure

After the power module is replaced, label it to facilitate subsequent operations.

Translation
Download
Updated: 2019-05-15

Document ID: EDOC1000084105

Views: 20929

Downloads: 140

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next