No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Product Description 15

OceanStor 5300 V3, 5500 V3, 5600 V3, 5800 V3, and 6800 V3 Storage System V300R003

This document introduces the storage system from the aspects of the market position, features, architecture, technical specifications, production configuration, environment requirement, standard compliance, and granted certifications.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Indicator Introduction

Indicator Introduction

After a controller enclosure is powered on, you can check the current operating status of the controller enclosure by viewing its indicators.

Indicators on the Front Panel

Figure 4-53 shows the indicators on the front panel of a controller enclosure.
Figure 4-53  Indicators on the front panel of a controller enclosure

1

Running/Alarm indicator on a BBU

2

Location indicator on the controller enclosure

3

Alarm indicator on the controller enclosure

4

Power indicator/Power button on the controller enclosure

5

Running/Alarm indicator of the fan module

6

Controller power indicator

7

Controller alarm indicator

   
Table 4-36 describes the indicators on the front panel of a controller enclosure.
Table 4-36  Indicators on the front panel of a controller enclosure

Module

No.

Indicator

Status and Description

BBU

1

Running/Alarm indicator on a BBU

  • Steady green: The BBU is fully charged.
  • Blinking green (1 Hz): The BBU is being charged.
  • Blinking green (4 Hz): The BBU is being discharged.
  • Steady red: The BBU is faulty.

System subrack

2

Location indicator on the controller enclosure

  • Blinking blue: The controller enclosure is being located.
  • Off: The controller enclosure is not located.

3

Alarm indicator on the controller enclosure

  • Steady red: An alarm about the controller enclosure is generated.
  • Off: The controller enclosure is working properly.

4

Power indicator/Power button on the controller enclosure

  • Steady green: The controller enclosure is powered on.
  • Blinking green (0.5 Hz): The controller enclosure is powered on for a short time.
  • Blinking green (1 Hz): The controller enclosure is in the burn-in test.
  • Blinking green (2 Hz): The controller enclosure is in the operating system boot process or in the power-off process.
  • Off: The controller enclosure is powered off or powered by BBUs.

Controller

5

Running/Alarm indicator of the fan module

  • Steady green: Fan modules are working correctly.
  • Steady red: The fan module is faulty.
  • Off: Fan modules are powered off.

6

Controller power indicator

  • Steady green: The controller is powered on.
  • Blinking green (0.5 Hz): The controller is powered on and in the BIOS boot process.
  • Blinking green (2 Hz): The controller is in the operating system boot process.
  • Off: The controller cannot be detected or is powered off.

7

Controller alarm indicator

  • Steady red: An alarm about the controller is generated.
  • Off: The controller is working correctly.

Indicators on the Rear Panel

Figure 4-54 shows the indicators on the rear panel of a controller enclosure.
Figure 4-54  Indicators on the rear panel of a controller enclosure

1

Running/Alarm indicator on a power module

2

Power indicator on a management module

3

Speed indicator of the management network port

4

Link/Active indicator of the management network port

5

Power indicator/Hot Swap button on an interface module

6

Speed indicator of a GE electrical port

7

Link/Active indicator of a GE electrical port

8

Speed indicator of a GE electrical port

9

Link/Active indicator of a GE electrical port

10

Link/Speed indicator of a 10 Gbit/s FCoE port

11

Link/Speed indicator of a 16 Gbit/s Fibre Channel port

12

Link/Speed indicator of an 8 Gbit/s Fibre Channel port

13

Indicator of the mini SAS HD expansion port

   

Table 4-37 describes the indicators on the rear panel of a controller enclosure.

Table 4-37  Indicators on the rear panel of a controller enclosure

Module

No.

Indicator

Status and Description

Power module

1

Running/Alarm indicator on a power module

  • Steady green: The power supply is normal.
  • Blinking green: The power input is normal but the device is powered off.
  • Steady red: The power module is faulty.
  • Off: No external power input is available.

Management module

2

Power indicator on a management module

  • Steady green: The module is working correctly.
  • Blinking green: The module receives a hot swap request.
  • Steady red: The module is faulty.
  • Off: The module is powered off or hot swappable.

3

Speed indicator of the management network port

  • Steady orange: Data is being transferred at the highest rate.
  • Off: The data transfer speed is lower than the highest speed.

4

Link/Active indicator of the management network port

  • Steady green: The port is connected properly.
  • Blinking green: Data is being transferred.
  • Off: The port is connected abnormally.

Interface module

5

Power indicator/Hot Swap button on an interface module

  • Steady green: The interface module is working correctly.
  • Blinking green: The interface module receives a hot swap request.
  • Steady red: The interface module is faulty.
  • Off: The interface module is powered off or can be hot-swappable.

6

Speed indicator of a GE electrical port

  • Steady orange: The data transfer rate between the controller enclosure and the application server is 1 Gbit/s.
  • Off: The data transfer rate between the controller enclosure and the application server is lower than 1 Gbit/s.

7

Link/Active indicator of a GE electrical port

  • Steady green: The connection between the controller enclosure and the application server is correct.
  • Blinking green: Data is being transferred.
  • Off: The connection between the controller enclosure and the application server is incorrect.

8

Speed indicator of a 10GE electrical port

  • Steady orange: The data transfer rate between the controller enclosure and the application server is 10 Gbit/s.
  • Off: The data transfer rate between the controller enclosure and the application server is lower than 10 Gbit/s.

9

Link/Active indicator of a 10GE electrical port

  • Steady green: The connection between the controller enclosure and the application server is correct.
  • Blinking green: Data is being transferred.
  • Off: The connection between the controller enclosure and the application server is incorrect.

10

Link/Speed indicator of a 10 Gbit/s FCoE port

  • Steady blue: The data transfer rate between the storage system and the application server is 10 Gbit/s.
  • Blinking blue: Data is being transferred.
  • Steady red: The port is faulty.
  • Off: The link to the port is down.

11

Link/Speed indicator of a 16 Gbit/s Fibre Channel port

  • Steady blue: The data transfer rate between the storage system and the application server is 16 Gbit/s.
  • Blinking blue: Data is being transferred.
  • Steady green: The data transfer rate between the storage system and the application server is 4 Gbit/s or 8 Gbit/s.
  • Blinking green: Data is being transferred.
  • Steady red: The port is faulty.
  • Off: The link to the port is down.

12

Link/Speed indicator of an 8 Gbit/s Fibre Channel port

  • Steady blue: The data transfer rate is 8 Gbit/s.
  • Blinking blue: Data is being transferred.
  • Steady green: The data transfer rate is 2 Gbit/s or 4 Gbit/s.
  • Blinking green: Data is being transferred.
  • Steady red: The port is faulty.
  • Off: The link to the port is down.

13

Indicator of the mini SAS HD expansion port

  • Steady blue: Data is transferred to the downstream disk enclosure at the rate of 4 x 12 Gbit/s.
  • Steady green: Data is transferred to the downstream disk enclosure at the rate of 4 x 3 Gbit/s or 4 x 6 Gbit/s.
  • Steady red: The port is faulty.
  • Off: The link to the port is down.
Translation
Download
Updated: 2019-02-01

Document ID: EDOC1000084184

Views: 34667

Downloads: 1133

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next