No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Command Reference 10

OceanStor 5300 V3, 5500 V3, 5600 V3, 5800 V3, and 6800 V3 Storage System V300R003

"Based on the CLI, this document describes how to use various commands classified by functions and how to set the CLI and manage the storage system through these commands. The document that you browse online matches the latest C version of the product. Click Download to download documents of other C versions."
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
change system management_ip

change system management_ip

Function

The change system management_ip command is used to configure an IP address for the management port on new hardware. Either an IPv4 and IPv6 address can be configured. The IP address can be used by terminals to access the storage system.

Format

change system management_ip eth_port_id=? ip_type=? [ ipv4_address=? mask=? [ gateway_ipv4=? ] ] [ ipv6_address=? prefix_length=? [ gateway_ipv6=? ] ] [ delete_gateway=? ]

Parameters

Parameter

Description

Value

eth_port_id=? Indicates the port ID.

To obtain the value, run "show system management_ip". The value contains 1 to 31 characters, including letters, digits, and periods (.). The value cannot start with a digit or a period (.), or end with a period (.).

ip_type=? Indicates the IP address type.

The value can be an IPv4 or IPv6 address.

ipv4_address=? Indicates the IPv4 address.

An IPv4 address cannot start with 0.

mask=? Indicates the IPv4 subnet mask of the management port.

-

gateway_ipv4=? Indicates the configured IPv4 gateway.

-

ipv6_address=? Indicates eth configured IPv6 address of the management port.

-

prefix_length=? Indicates the configured IPv6 subnet mask.

-

gateway_ipv6=? Indicates the configured IPv6 gateway of the management port.

The value must be an IPv6 address.

delete_gateway=? Whether the original gateway needs to be deleted.

The value can be "yes" or "no",where:1:"yes":the gateway of the port will be deleted.2:"no":the gateway of the port will not be deleted.

Level

Administrator

Usage Guidelines

  • When the maintenance terminal and the storage system are not in the same network segment, the terminal cannot access the storage system. You have to add a router to the maintenance terminal and a gateway to the storage system so that the maintenance terminal can access the storage system.
  • Before performing the operation, ensure that the address you entered is valid. Note that an IPv4 address cannot start with 0.
  • Changing the IP address of the management port may disconnect a user that has logged in from the storage system. You need to log in to the storage system again after changing the IP address.
  • A maintenance terminal can access the storage system using the IPv4 address or IPv6 address of the management network port.

Example

Set the IPv4 address of a specific management network port to 192.168.190.2 and the subnet mask to 255.255.0.0, and deleting the original gateway. The command output varies with product models.

admin:/>change system management_ip eth_port_id=CTE0.A.H4 ip_type=ipv4_address ipv4_address=192.168.190.2 mask=255.255.0.0 delete_gateway=yes
WARNING: You are about to change the IP address of management network port. If you enter an unavailable IP address, the DeviceManager will become inaccessible.
Suggestion: Before performing this operation, ensure that the entered IP address is available.
Have you read warning message carefully?(y/n)y
Are you sure you really want to perform the operation?(y/n)y
Command executed successfully.

System Response

None

Translation
Download
Updated: 2019-04-04

Document ID: EDOC1000084195

Views: 278798

Downloads: 1559

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next