No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

CH225 V3 Compute Node V100R001 User Guide 07

This document describes the appearance, functions, and structure of the CH225 V3 storage expansion compute node (CH225 V3 for short), and methods of installing, removing, and configuring the CH225 V3.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Installing a CH225 V3

Installing a CH225 V3

This section describes the procedure and precautions for installing a CH225 V3 in an E9000 chassis.

Scenarios

Install a CH225 V3 in a Huawei E9000 chassis. Ensure that you are familiar with the hardware devices before the operation.

Impact on the System

This operation has no adverse impact on the system.

Prerequisites

Conditions

Data

Data preparation is not required for this operation.

Tools

The following tools are available before the operation:

  • Protective gloves.
  • ESD gloves.
  • ESD wrist strap.
  • Box cutter.

Workflow

Figure 3-1 shows the process for installing a CH225 V3.

Figure 3-1 Installation process

Procedure

  1. Unpack the CH225 V3.

    1. Check whether the packing case and seals are in good condition.
      NOTE:

      If the packing case is damaged (for example, the packing case is soaked or deformed, or the seals or pressure-sensitive adhesive tape is unsealed), fill in the Cargo Problems Feedback Form.

    2. Hold the box cutter properly to avoid hurting hands or damaging the device in the packing case.

      Use a box cutter to cut the pressure-sensitive adhesive tape on the packing case.

    3. Unpack the CH225 V3, as shown in Figure 3-2.
      Figure 3-2 Unpacking a CH225 V3
    4. Take out the CH225 V3s together with ESD bags and place them separately on an ESD mat, as shown in Figure 3-3.
      Figure 3-3 Proper operation
      NOTE:

      Do not take out the CH225 V3 from its ESD bag if you do not install it immediately.

      Figure 3-4 Improper operations

  2. Determine the position for installing the CH225 V3 in the chassis. Figure 3-5 shows the numbering of the full-width slots.

    Figure 3-5 Slot numbers

  3. Remove the filler panel.

    1. Press and hold the grooves inward on both sides of the filler panel and remove the filler panel. See step (1) and step (2) in Figure 3-6.
      Figure 3-6 Removing the filler panel
    2. Place the removed filler panel in an accessory recycling bin.

  4. Install the CH225 V3.

    1. (Optional) Remove the partition board, as shown in Figure 3-7.
      The partition board must be removed before you install a full-width compute node.
      1. Press and hold down the hole and push the partition board inwards. See steps (1) and (2) in Figure 3-7.
      2. Move the partition board rightwards and remove the partition board. See steps (3) and (4) in Figure 3-7.
      Figure 3-7 Removing the partition board
    2. Press the release buttons on the CH225 V3. See step (1) in Figure 3-8.
      Figure 3-8 Installing the CH225 V3
    3. Open the ejector levers on the CH225 V3 completely. See step (2) in Figure 3-8.
    4. Insert the CH225 V3 horizontally into the chassis until it comes into contact with the signal backplane. See step (3) in Figure 3-8.
    5. Close the ejector levers on the CH225 V3. See step (4) in Figure 3-8.

  5. Check the indicator status.

    Check the indicator status after the CH225 V3 is powered on.

    For details about the indicators, see Table 2-1.

Translation
Download
Updated: 2019-07-10

Document ID: EDOC1000095351

Views: 7960

Downloads: 74

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next