No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

CLI-based Configuration Guide - IP Multicast

AR120, AR150, AR160, AR200, AR1200, AR2200, AR3200, and AR3600 V200R007

This document describes the principles and configurations of IP multicast, and provides configuration examples.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring IPv6 PIM GR

Configuring IPv6 PIM GR

Pre-configuration Tasks

Before configuring IPv6 PIM GR, complete the following tasks:

  • Configure an IPv6 unicast routing protocol to ensure normal unicast routing on the network.
  • Enable IPv6 PIM-SM.

Context

NOTE:

Only the AR3200 series routers support IPv6 PIM GR.

Multicast devices may need to perform active/standby switchovers in some scenarios, for example, when the multicast devices need to be upgraded or their control boards fail. After an active/standby switchover, the new active main control board deletes the forwarding entries on interface boards and re-learns the IPv6 PIM routing table and multicast forwarding table. During this process, multicast traffic is interrupted.

IPv6 PIM-SM supports the IPv6 PIM GR function on a device with dual main control boards. IPv6 PIM GR ensures normal multicast data forwarding during active/standby switchover on the device.

After the PIM GR function is configured, the active main control board of the multicast device backs up IPv6 PIM routing entries and Join/Prune information to be sent upstream to the standby main control board. The interface boards maintain forwarding entries. When an active/standby switchover occurs in the system, the multicast device can quickly send Join messages upstream to maintain the Join state of the upstream multicast device. Then, the IPv6 PIM protocol sends Hello messages carrying Generation IDs to all neighbors with IPv6 PIM-SM enabled. When a downstream multicast device finds that the Generation ID of its neighbor changes, it sends a Join/Prune message to the neighbor so that the neighbor can create new routing entries. This mechanism ensures nonstop forwarding of multicast data on the forwarding plane.

On a network using dynamic RP, when a DR receives a Hello message with a Generation ID different from the previous one, the DR sends a unicast Bootstrap message to the multicast device. The multicast device then restores the RP information from the Bootstrap message. If the multicast device cannot learn RP information from the Bootstrap message, it obtains RP information from the Join/Prune messages received from downstream devices and generates new multicast entries.

Default Configuration

The default IPv6 PIM GR period is 120s.

Procedure

  1. Run:

    system-view

    The system view is displayed.

  2. Run:

    pim-ipv6

    The PIM-IPv6 view is displayed.

  3. Run:

    graceful-restart

    PIM GR is enabled.

    By default, IPv6 PIM GR is not enabled.

  4. (Optional) Run:

    graceful-restart period period

    The PIM GR period is configured.

    By default, the IPv6 PIM GR period is 120 seconds.

Checking the Configuration

After IPv6 PIM GR is configured, you can run the following commands to check entries in the IPv6 PIM routing table.

  • display pim ipv6 routing-table [ ipv6-source-address [ mask mask-length ] | ipv6-group-address [ mask mask-length ] | flags flag-value | fsm | incoming-interface { interface-type interface-number | register } | mode { dm | sm | ssm } | outgoing-interface { exclude | include | match } { interface-type interface-number | none | register } ] * [ outgoing-interface-number [ number ] ]
  • display pim ipv6 routing-table brief [ ipv6-source-address [ mask mask-length ] | ipv6-group-address [ mask mask-length ] | incoming-interface { interface-type interface-number | register } ] *

Translation
Download
Updated: 2019-06-12

Document ID: EDOC1000097181

Views: 17100

Downloads: 399

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next