No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

CLI-based Configuration Guide - IP Multicast

AR120, AR150, AR160, AR200, AR1200, AR2200, AR3200, and AR3600 V200R007

This document describes the principles and configurations of IP multicast, and provides configuration examples.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Adjusting Control Parameters for Establishing Neighbor Relationships

Adjusting Control Parameters for Establishing Neighbor Relationships

Configuration Process

You can configure the Hello message control parameters, and neighbor filtering function in any sequence as required.

Adjusting Control Parameters for Hello Messages

Context

PIM devices send Hello messages periodically to maintain PIM neighbor relationships. When a PIM device receives a Hello message from a neighbor, the PIM device starts the timer and sets the timer to the holdtime of Hello messages. If the PIM device does not receive a new Hello message from the neighbor within the holdtime, it considers the neighbor invalid or unreachable. Therefore, the interval for a PIM device to send Hello messages must be smaller than the holdtime of Hello messages.

If multiple PIM devices transmit Hello messages simultaneously, a conflict occurs on the network. To solve this problem, when a PIM device receives a Hello message, it waits a period before transmitting the Hello message. This period can be a random value and is smaller than the maximum delay for triggering Hello messages.

NOTE:
  • The interval for sending Hello messages and the holdtime of Hello messages can be set either globally or on an interface. If you configure the two parameters in the global PIM-IPv6 view and in the interface view simultaneously, the configuration in the interface view takes effect.

  • You can configure the maximum delay for triggering Hello messages only in the interface view.

Default Configuration

Table 5-4 lists default configuration of control parameters for Hello messages.

Table 5-4  Default configuration of control parameters for Hello messages
Parameter Default Setting

Interval for sending Hello messages

30s

Holdtime of Hello messages

105s

Maximum delay for triggering Hello messages

5s

Procedure

  • Global configuration
    1. Run:

      system-view

      The system view is displayed.

    2. Run:

      pim-ipv6

      The PIM-IPv6 view is displayed.

    3. Run:

      timer hello interval

      The interval for sending Hello messages is configured.

    4. Run:

      hello-option holdtime interval

      The holdtime of Hello messages is configured.

  • Configuration on an interface
    1. Run:

      system-view

      The system view is displayed.

    2. Run:

      interface interface-type interface-number

      The interface view is displayed.

    3. Run:

      pim ipv6 timer hello interval

      The interval for sending Hello messages is configured.

    4. Run:

      pim ipv6 hello-option holdtime interval

      The holdtime of Hello messages is configured.

    5. Run:

      pim ipv6 triggered-hello-delay interval

      The maximum delay for triggering Hello messages is configured.

Configuring PIM Neighbor Filtering

Context

The router supports different neighbor filtering policies to ensure secure and effective multicast transmission in an IPv6 PIM-DM domain. You can perform the following operations to filter neighbors:
  • Configure a valid neighbor address range to prevent unauthorized neighbors from connecting to the network.
  • Configure the router to reject Hello messages without Generation IDs so that the router connects only to normally working PIM neighbors.

Procedure

  1. Run:

    system-view

    The system view is displayed.

  2. Run:

    interface interface-type interface-number

    The interface view is displayed.

  3. Run:

    pim ipv6 neighbor-policy { basic-acl6-number | acl6-name acl6-name }

    The range of valid neighbor addresses is configured.

    • If the IP address of a PIM neighbor that has established a neighbor relationship with the router is not in the configured range of valid neighbor addresses, the router will no longer receive Hello messages from this PIM neighbor. When the holdtime of Hello messages expires, the neighbor relationship between the PIM device and the router is terminated.

    • When configuring an ACL rule for the interface, use the permit parameter to configure the interface to accept only Hello messages with source addresses in a specified range. If no rule is configured in the ACL, the interface discards Hello messages from all source addresses.

  4. Run:

    pim ipv6 require-genid

    The router is configured to receive only Hello messages that contain Generation IDs.

Checking the Configuration

Context

After the control parameters for establishing the neighbor relationship are adjusted, you can check information about the IPv6 PIM interface and the IPv6 PIM neighbor.

Procedure

  • Run the display pim ipv6 interface [ interface-type interface-number | up | down ] [ verbose ] command to check IPv6 PIM information on an interface.
  • Run the display pim ipv6 neighbor [ ipv6-link-local-address | interface interface-type interface-number | verbose ] * command to check information about IPv6 PIM neighbors.
Translation
Download
Updated: 2019-06-12

Document ID: EDOC1000097181

Views: 20750

Downloads: 401

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next