No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

MIB Reference

AR120, AR150, AR160, AR200, AR1200, AR2200, AR3200, and AR3600 V200R007

This document provides the function overview, relationships between tables, description of single objects, description of MIB tables, and description of alarm objects.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
ipv6RouteTable

ipv6RouteTable

This table is used to describe IPv6 routing information saved on the network device.

The indexes of this table are ipv6RouteDest, ipv6RoutePfxLength, and ipv6RouteIndex.

OID

Object Name

Syntax

Max Access

Description

Implemented Specifications

1.3.6.1.2.1.55.1.11.1.1

ipv6RouteDest

Ipv6Address

Not-accessible

This object indicates the destination IPv6 address of this route. This object may not take a multicast address value.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.2.1.55.1.11.1.2

ipv6RoutePfxLength

INTEGER(0..128)

Not-accessible

The value of this object identifies the prefix length of the destination address.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.2.1.55.1.11.1.3

ipv6RouteIndex

Unsigned32

Not-accessible

The value which uniquely identifies the route among the routes to the same network layer destination.

The way this value is chosen is implementation specific but it must be unique for ipv6RouteDest/ipv6RoutePfxLength pair and remain constant for the life of the route.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.2.1.55.1.11.1.4

ipv6RouteIfIndex

Ipv6IfIndexOrZero

Read-only

The index value which uniquely identifies the local interface through which the next hop of this route should be reached.

The interface identified by a particular value of this index is the same interface as identified by the same value of ipv6IfIndex.

For routes of the discard type this value can be zero.

The value ranges from 0 to 2147483647.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.2.1.55.1.11.1.5

ipv6RouteNextHop

Ipv6Address

Read-only

On remote routes, the address of the next system en route; otherwise, ::0.('00000000000000000000000000000000'H in ASN.1 string representation).

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.2.1.55.1.11.1.6

ipv6RouteType

INTEGER{other(1),discard(2),local(3),remote(4)}

Read-only

The value of this object identifies the route type.

The values are as follows:

  • other(1)
  • discard(2): refers to a route indicating that packets to destinations matching this route are to be discarded (sometimes called black-hole route).
  • local(3): refers to a route for which the next hop is the final destination.
  • remote(4): refers to a route for which the next hop is not the final destination.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.2.1.55.1.11.1.7

ipv6RouteProtocol

INTEGER{other(1),local(2),netmgmt(3),ndisc(4),rip(5),ospf(6),bgp(7),idrp(8),igrp(9)}

Read-only

The value of this object identifies the route learning mechanism.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.2.1.55.1.11.1.8

ipv6RoutePolicy

Integer32

Read-only

The general set of conditions that would cause the selection of one multipath route (set of next hops for a given destination) is referred to as 'policy'. Unless the mechanism indicated by ipv6RouteProtocol specified otherwise, the policy specifier is the 8-bit Traffic Class field of the IPv6 packet header that is zero extended at the left to a 32-bit value.

Protocols defining 'policy' otherwise must either define a set of values which are valid for this object or must implement an integer-instanced policy table for which this object's value acts as an index.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.2.1.55.1.11.1.9

ipv6RouteAge

Unsigned32

Read-only

The value of this object identifies the number of seconds since this route was last updated or the route was determined to be correct.

Note that no semantics of 'too old' can be implied except through knowledge of the routing protocol by which the route was learned.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.2.1.55.1.11.1.10

ipv6RouteNextHopRDI

Unsigned32

Read-only

The value of this object identifies the routing domain ID of the next hop.

The semantics of this object are determined by the routing-protocol specified in the route's ipv6RouteProtocol value.

When this object is unknown or not relevant, its value should be set to zero.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.2.1.55.1.11.1.11

ipv6RouteMetric

Unsigned32

Read-only

The value of this object identifies the metric value of this route. The semantics of this metric are determined by the routing protocol specified in the route's ipv6RouteProtocol value.

When this is unknown or not relevant to the protocol indicated by ipv6RouteProtocol, the object value should be set to its maximum value (4294967295).

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.2.1.55.1.11.1.12

ipv6RouteWeight

Unsigned32

Read-only

The value of this object identifies the system internal weight of this route. The semantics of this value are determined by the implementation specific rules.

Generally, within routes with the same ipv6RoutePolicy value, the lower the weight value the more preferred is the route.

This object is implemented as defined in the corresponding MIB files.

1.3.6.1.2.1.55.1.11.1.13

ipv6RouteInfo

RowPointer

Read-only

A reference to MIB definitions specific to the particular routing protocol which is responsible for this route, as determined by the value specified in the route's ipv6RouteProtocol value.

If this information is not present, its value should be set to the OBJECT IDENTIFIER 0 0, which is a syntactically valid object identifier, and any implementation conforming to ASN.1 and the Basic Encoding Rules must be able to generate and recognize this value.

Currently, the return value 0.0 is supported only.

1.3.6.1.2.1.55.1.11.1.14

ipv6RouteValid

TruthValue

Read-write

Setting this object to the value 'false(2)' has the effect of invalidating the corresponding entry in the ipv6RouteTable object. That is, it effectively disassociates the destination identified with said entry from the route identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant ipv6RouteValid object.

The values are as follows:
  • true(1)
  • false(2)

Currently, the maximum access is read-only.

Creation Restriction

No entry can be created in this table.

Modification Restriction

The entries in this table cannot be modified.

Deletion Restriction

The entries in this table cannot be deleted.

Access Restriction

IPv6 routes exist on the device.

Translation
Download
Updated: 2019-06-05

Document ID: EDOC1000097213

Views: 125314

Downloads: 688

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next