No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search


To have a better experience, please upgrade your IE browser.


AR500, AR510, and AR530 V200R007 Commands Reference

This document describes all the configuration commands of the device, including the command function, syntax, parameters, views, default level, usage guidelines, examples, and related commands.

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
acl ipv6 (system view)

acl ipv6 (system view)


The acl ipv6 command creates a numbered ACL6 and enters the ACL6 view.

The undo acl ipv6 command deletes a numbered ACL6.

By default, no numbered ACL6 is created.


AR502G-L-D-H, and AR502GR-L-D-H do not support this command.

AR510 series does not support this command.


AR502G-L-D-H, AR502GR-L-D-H, AR510 series do not support IPv6 ACL.


acl ipv6 [ number ] acl6-number [ match-order { auto | config } ]

undo acl ipv6 { all | [ number ] acl6-number }


Parameter Description Value
number Indicates the number that identifies an ACL. -
acl6-number Specifies an ACL6 number.

The value is an integer that ranges from 2000 to 3999.

  • The value of a basic ACL6 ranges from 2000 to 2999.
  • The value of an advanced ACL6 ranges from 3000 to 3999.
match-order { auto | config }

Indicates the matching order of ACL6 rules.

  • auto:

    indicates that ACL6 rules are matched based on the depth first principle.

    If the ACL rules are of the same depth first order, they are matched in ascending order of rule IDs.

  • config: indicates that ACL6 rules are matched based on the configuration order.

    The ACL6 rules are matched based on the configuration order only when the rule ID is not specified. If rule IDs are specified, the ACL6 rules are matched in ascending order of rule IDs.

If the match-order parameter is not specified when you create an ACL6, the default match order config is used.

all Indicates that all the configured ACL6s are deleted. -


System view

Default Level

2: Configuration level

Usage Guidelines

Usage Scenario

An ACL6 is a set of rules composed of permit or deny clauses. ACL6 rules can be referenced by modules. ACL6s are applicable to QoS. ACL6s can limit data flows to improve network performance. For example, ACL6s are configured on an enterprise network to limit video data flows, which lowers the network load and improves network performance.

Follow-up Procedure

Run the rule command to configure ACL6 rules and apply the ACL6 to services which packets need to be filtered .


After you create a named ACL6 by using the acl ipv6 command, the ACL6 still exists even if you exit from the ACL6 view. You must run the undo acl ipv6 acl6-number command to delete the ACL6.

When you delete an ACL6 that has been referenced by other services, the services may be interrupted. Before deleting an ACL6, ensure that the ACL6 is unused.

All ACL6s can be deleted on the device at one time, whereas this method is not recommended.


# Create an ACL6 with the number of 3000.

<Huawei> system-view
[Huawei] acl ipv6 number 3000
Updated: 2019-05-29

Document ID: EDOC1000097293

Views: 138596

Downloads: 150

Average rating:
This Document Applies to these Products

Related Version

Related Documents

Previous Next