No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

AR500, AR510, and AR530 V200R007 Commands Reference

This document describes all the configuration commands of the device, including the command function, syntax, parameters, views, default level, usage guidelines, examples, and related commands.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
WLAN Service Configuration Commands

WLAN Service Configuration Commands

80211a basic-rate

Function

The 80211a basic-rate command configures a basic rate set of the 802.11a protocol in the radio profile.

The undo 80211a basic-rate command restores the default basic rate set of the 802.11a protocol in the radio profile.

By default, a basic rate set of the 802.11a protocol in the radio profile includes rates 6 Mbps, 12 Mbps, and 24 Mbps.

Format

80211a basic-rate [ 80211a-rate-value &<1-8> | all ]

undo 80211a basic-rate

Parameters

Parameter

Description

Value

80211a-rate-value

Specifies an 802.11a basic rate set.

Enumerated type:
  • 6: 6 Mbps
  • 9: 9 Mbps
  • 12: 12 Mbps
  • 18: 18 Mbps
  • 24: 24 Mbps
  • 36: 36 Mbps
  • 48: 48 Mbps
  • 54: 54 Mbps

all

Supports all basic rates.

-

Views

Radio profile view

Default Level

2: Configuration level

Usage Guidelines

Usage Scenario

The rates specified in the basic rate set must be supported by both the AP and STA; otherwise, the STA cannot associate with the AP. For example, if you configure the basic rate set to contain rates 6 Mbps and 9 Mbps and deliver the configuration to an AP, only STAs supporting the two rates can associate with the AP. The AP and STA select a rate from the basic rate set or the supported rate set to transmit packets.

After you run this command to configure a basic rate set in the radio profile, bind the radio profile to the AP's 5 GHz radio. If a STA associates with the AP in 802.11a mode, the STA must support all rates specified by the basic rate set; otherwise, the STA cannot associate with the AP.

Configuration Precautions

This configuration applies only to STAs associated with an AP in 802.11a mode but does not take effect on STAs associated with the AP in other modes.

The basic rate set and supported rate set cannot be empty simultaneously.

If no parameter is specified in the command, the basic rate set contains no rate settings.

Example

# Configure the 802.11a basic rate set to contain rates 6 Mbps and 9 Mbps in the radio profile.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] radio-profile name radiopf
[Huawei-wlan-radio-prof-radiopf] 80211a basic-rate 6 9
Related Topics

80211a supported-rate

Function

The 80211a supported-rate command configures a supported rate set of the 802.11a protocol in the radio profile.

The undo 80211a supported-rate command restores the default supported rate set of the 802.11a protocol in the radio profile.

By default, the supported rate set of the 802.11a protocol in the radio profile includes rates 6 Mbps, 9 Mbps, 12 Mbps, 18 Mbps, 24 Mbps, 36 Mbps, 48 Mbps, and 54 Mbps.

Format

80211a supported-rate [ 80211a-rate-value &<1-8> | all ]

undo 80211a supported-rate

Parameters

Parameter

Description

Value

80211a-rate-value

Specifies an 802.11a supported rate set.

Enumerated type:
  • 6: 6 Mbps
  • 9: 9 Mbps
  • 12: 12 Mbps
  • 18: 18 Mbps
  • 24: 24 Mbps
  • 36: 36 Mbps
  • 48: 48 Mbps
  • 54: 54 Mbps

all

Supports all rates.

-

Views

Radio profile view

Default Level

2: Configuration level

Usage Guidelines

Usage Scenario

The supported rate set contains rates supported by the AP except the basic rates. The AP and STA can transmit data at all rates specified by the supported rate set. The AP and STA select a rate from the basic rate set or the supported rate set to transmit packets.

When a STA supports rates specified in the basic rate set, the STA can associate with the AP regardless of whether the STA supports rates specified in the supported rate set. In this case, the AP and STA can only select a rate from the basic rate set to transmit packets. For example, assume that you configure the basic rate set to contain rates 6 Mbps and 9 Mbps and the supported rate set to contain rates 48 Mbps and 54 Mbps. After you deliver the configurations to an AP, the STA supporting 6 Mbps and 9 Mbps can associate with the AP, and select either of the two rates to transmit packets with the AP. However, if the STA supports 6 Mbps, 9 Mbps, and 54 Mbps, the STA and AP select any of the three rates to transmit packets after the STA associates with the AP.

After you run this command to configure a supported rate set in the radio profile, bind the radio profile to the AP's 5 GHz radio. If a STA associates with the AP in 802.11a mode, the AP and STA select a rate from the basic rate set or supported rate set to transmit packets.

Configuration Precautions

This configuration applies only to STAs associated with an AP in 802.11a mode but does not take effect on STAs associated with the AP in other modes.

The basic rate set and supported rate set cannot be empty simultaneously.

If no parameter is specified in the command, the supported rate set contains no rate settings.

Example

# Configure the 802.11a supported rate set to contain rates 6 Mbps and 9 Mbps in the radio profile.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] radio-profile name radiopf
[Huawei-wlan-radio-prof-radiopf] 80211a supported-rate 6 9
Related Topics

80211ac a-mpdu

Function

The 80211ac a-mpdu command sets the the maximum length of an aggregated MPDU (A-MPDU) on the 802.11ac radio. MPDU stands for MAC protocol data unit.

The undo 80211ac a-mpdu command restores the maximum length of an A-MPDU on the 802.11ac radio to the default value.

By default, the index for the maximum length of an A-MPDU is 7. The maximum length of the A-MPDU is 1048575 bytes.

NOTE:

Only the AP2030DN, AP4030DN, AP4130DN, AP7030DE, AP8030DN, AP8130DN, AP5030DN and AP5130DN support 802.11ac.

Format

80211ac a-mpdu max-length-exponent length-capability-index

undo 80211ac a-mpdu max-length-exponent

Parameters

Parameter

Description

Value

max-length-exponent length-capability-index

Indicates the index for the maximum length of the A-MPDU.

The value is an integer that ranges from 0 to 7.

  • 0: indicates that the maximum length of the A-MPDU is 8191 bytes.
  • 1: indicates that the maximum length of the A-MPDU is 16383 bytes.
  • 2: indicates that the maximum length of the A-MPDU is 32767 bytes.
  • 3: indicates that the maximum length of the A-MPDU is 65535 bytes.
  • 4: indicates that the maximum length of the A-MPDU is 131071 bytes.
  • 5: indicates that the maximum length of the A-MPDU is 262143 bytes.
  • 6: indicates that the maximum length of the A-MPDU is 524287 bytes.
  • 7: indicates that the maximum length of the A-MPDU is 1048575 bytes.

Views

Radio profile view

Default Level

2: Configuration level

Usage Guidelines

To reduce costs, 802.11ac uses frame aggregation technology that aggregates two or more frames into an A-MPDU to transmit.

Example

# Set the maximum length of an A-MPDU to 32767 bytes in radio profile rp01.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] radio-profile id 1 name rp01  
[Huawei-wlan-radio-prof-rp01] 80211ac a-mpdu max-length-exponent 2

80211ac supported-mcs

Function

The 80211ac supported-mcs command configures the maximum MCS value corresponding to a specific number of 802.11ac spatial streams in the radio profile.

The undo 80211ac supported-mcs command restores the default maximum MCS value corresponding to a specific number of 802.11ac spatial streams in the radio profile.

By default, the maximum MCS value of the 802.11 ac radios is 9 in the radio profile.

Format

80211ac supported-mcs { nss nss-value { max-mcs max-mcs-value | disable } } &<1-3>

undo 80211ac supported-mcs

Parameters

Parameter

Description

Value

nss nss-value Specifies the number of spatial streams. The value is an integer ranging from 1 to 3.
max-mcs max-mcs-value Specifies the maximum MCS value corresponding to a specific number of spatial streams. The value is an integer ranging from 7 to 9.
disable Indicates that the spatial streams do not support configuration of the maximum MCS value. -

Views

Radio profile view

Default Level

2: Configuration level

Usage Guidelines

Usage Scenario

Rates of 802.11ac radios depend on the index value of Modulation and Coding Scheme (MCS). A larger MCS value indicates a higher transmission rate.

After you run this command to configure the maximum MCS values, the AC delivers the maximum MCS values to APs based on the number of spatial streams supported by each AP. For example, an AP supports two spatial streams and the AC delivers the maximum MCS value corresponding to nss 2 to the AP.

Configuration Precautions

This configuration applies only to STAs associated with an AP in 802.11ac mode but does not take effect on STAs associated with the AP in other modes.

This command configures maximum MCS values corresponding to different numbers of spatial streams, for example, the maximum MCS values 7, 8, 9 correspond to one, two, and three spatial streams respectively.

You must configure the same maximum MCS value for AP5030s with different numbers of spatial streams. If you configure different MCS values, the minimum MCS value takes effect. For example, if you configure the maximum MCS values 7, 8, and 9 for different numbers of spatial streams, the MCS value 7 takes effect on AP5030s.

nss-value cannot be repeatedly configured in a command.

Example

# Configure the maximum MCS value 8 for 802.11ac radios with two spatial streams in the radio profile.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] radio-profile name radiopf
[Huawei-wlan-radio-prof-radiopf] 80211ac supported-mcs nss 2 max-mcs 8

80211bg basic-rate (for AC)

Function

The 80211bg basic-rate command configures a basic rate set of the 802.11bg protocol in the radio profile.

The undo 80211bg basic-rate command restores the default basic rate set of the 802.11bg protocol in the radio profile.

By default, the basic rate set of the 802.11bg protocol includes rates 1 Mbps and 2 Mbps in the radio profile.

Format

80211bg basic-rate [ 80211bg-rate-value &<1-12> | all ]

undo 80211bg basic-rate

Parameters

Parameter

Description

Value

80211bg-rate-value

Specifies an 802.11bg basic rate set.

Enumerated type:
  • 1: 1 Mbps
  • 2: 2 Mbps
  • 5: 5.5 Mbps
  • 6: 6 Mbps
  • 9: 9 Mbps
  • 11: 11 Mbps
  • 12: 12 Mbps
  • 18: 18 Mbps
  • 24: 24 Mbps
  • 36: 36 Mbps
  • 48: 48 Mbps
  • 54: 54 Mbps

all

Supports all basic rates.

-

Views

Radio profile view

Default Level

2: Configuration level

Usage Guidelines

Usage Scenario

The rates specified in the basic rate set must be supported by both the AP and STA; otherwise, the STA cannot associate with the AP. For example, if you configure the basic rate set to contain rates 6 Mbps and 9 Mbps and deliver the configuration to an AP, only STAs supporting the two rates can associate with the AP. The AP and STA select a rate from the basic rate set or the supported rate set to transmit packets.

After you run this command to configure a basic rate set in the radio profile, bind the radio profile to the AP's 2.4 GHz radio. If a STA associates with the AP in 802.11bg mode, the STA must support all rates specified by the basic rate set; otherwise, the STA cannot associate with the AP.

Configuration Precautions

This configuration applies only to STAs associated with an AP in 802.11bg mode but does not take effect on STAs associated with the AP in other modes.

The basic rate set and supported rate set cannot be empty simultaneously.

If no parameter is specified in the command, the basic rate set contains no rate settings.

Example

# Configure the 802.11bg basic rate set to contain rates 6 Mbps and 9 Mbps in the radio profile.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] radio-profile name radiopf
[Huawei-wlan-radio-prof-radiopf] 80211bg basic-rate 6 9

80211bg supported-rate (for AC)

Function

The 80211bg supported-rate command configures a supported rate set of the 802.11bg protocol in the radio profile.

The undo 80211bg supported-rate command restores the default supported rate set of the 802.11bg protocol in the radio profile.

By default, the supported rate set of the 802.11bg protocol in the radio profile includes rates 1 Mbps, 2 Mbps, 5.5 Mbps, 6 Mbps, 9 Mbps, 11 Mbps, 12 Mbps, 18 Mbps, 24 Mbps, 36 Mbps, 48 Mbps, and 54 Mbps.

Format

80211bg supported-rate [ 80211bg-rate-value &<1-12> | all ]

undo 80211bg supported-rate

Parameters

Parameter

Description

Value

80211bg-rate-value

Specifies an 802.11bg supported rate set.

Enumerated type:
  • 1: 1 Mbps
  • 2: 2 Mbps
  • 5: 5.5 Mbps
  • 6: 6 Mbps
  • 9: 9 Mbps
  • 11: 11 Mbps
  • 12: 12 Mbps
  • 18: 18 Mbps
  • 24: 24 Mbps
  • 36: 36 Mbps
  • 48: 48 Mbps
  • 54: 54 Mbps

all

Supports all rates.

-

Views

Radio profile view

Default Level

2: Configuration level

Usage Guidelines

Usage Scenario

The supported rate set contains rates supported by the AP except the basic rates. The AP and STA can transmit data at all rates specified by the supported rate set. The AP and STA select a rate from the basic rate set or the supported rate set to transmit packets.

When a STA supports rates specified in the basic rate set, the STA can associate with the AP regardless of whether the STA supports rates specified in the supported rate set. In this case, the AP and STA can only select a rate from the basic rate set to transmit packets. For example, assume that you configure the basic rate set to contain rates 6 Mbps and 9 Mbps and the supported rate set to contain rates 48 Mbps and 54 Mbps. After you deliver the configurations to an AP, the STA supporting 6 Mbps and 9 Mbps can associate with the AP, and select either of the two rates to transmit packets with the AP. However, if the STA supports 6 Mbps, 9 Mbps, and 54 Mbps, the STA and AP select any of the three rates to transmit packets after the STA associates with the AP.

After you run this command to configure a supported rate set in the radio profile, bind the radio profile to the AP's 2.4 GHz radio. If a STA associates with the AP in 802.11bg mode, the AP and STA select a rate from the basic rate set or supported rate set to transmit packets.

Configuration Precautions

This configuration applies only to STAs associated with an AP in 802.11bg mode but does not take effect on STAs associated with the AP in other modes.

The basic rate set and supported rate set cannot be empty simultaneously.

If no parameter is specified in the command, the supported rate set contains no rate settings.

Example

# Configure the 802.11bg supported rate set to contain rates 6 Mbps and 9 Mbps in the radio profile.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] radio-profile name radiopf
[Huawei-wlan-radio-prof-radiopf] 80211bg supported-rate 6 9

80211n a-mpdu enable (for AC)

Function

The 80211n a-mpdu enable command enables aggregation of MPDUs.

The undo 80211n a-mpdu enable command disables aggregation of MPDUs.

By default, aggregation of MPDUs is enabled.

Format

80211n a-mpdu enable

undo 80211n a-mpdu enable

Parameters

None

Views

Radio profile view

Default Level

2: Configuration level

Usage Guidelines

To reduce cost, 802.11n uses frame aggregation technology that aggregates two or more frames into an A-MPDU to transmit.

Example

# Enable aggregation of MPDUs.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] radio-profile id 1 name rp01  
[Huawei-wlan-radio-prof-rp01] 80211n a-mpdu enable   

80211n a-mpdu (for AC)

Function

The 80211n a-mpdu command sets the maximum length of an aggregated MPDU (A-MPDU). MPDU stands for MAC protocol data unit.

The undo 80211n a-mpdu command restores the maximum length of an A-MPDU to the default value.

By default, the index for the maximum length of an A-MPDU is 3. The maximum length of the A-MPDU is 65535 bytes.

Format

80211n a-mpdu max-length-exponent length-capability-index

undo 80211n a-mpdu max-length-exponent

Parameters

Parameter

Description

Value

max-length-exponent length-capability-index

Indicates the index for the maximum length of the A-MPDU.

The value is an integer that ranges from 0 to 3.

  • 0: indicates that the maximum length of the A-MPDU is 8191 bytes.
  • 1: indicates that the maximum length of the A-MPDU is 16383 bytes.
  • 2: indicates that the maximum length of the A-MPDU is 32767 bytes.
  • 3: indicates that the maximum length of the A-MPDU is 65535 bytes.

Views

Radio profile view

Default Level

2: Configuration level

Usage Guidelines

Usage Scenario

To reduce costs, 802.11n uses frame aggregation technology that aggregates two or more frames into an A-MPDU to transmit.

Prerequisites

The radio type of the radio profile has been set to 80211an, 80211gn, 80211bgn, or 80211n.

Example

# Set the maximum length of an A-MPDU to 32767 bytes in radio profile rp01.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] radio-profile id 1 name rp01  
[Huawei-wlan-radio-prof-rp01] 80211n a-mpdu max-length-exponent 2

guard-interval-mode (for AC)

Function

The guard-interval-mode command configures the guard interval (GI) mode.

The undo guard-interval-mode command restores the default GI mode.

By default, the GI mode is normal.

Format

guard-interval-mode { short | normal }

undo guard-interval-mode

Parameters

Parameter

Description

Value

short

Indicates a short interval.

-

normal

Indicates a common interval.

-

Views

Radio profile view

Default Level

2: Configuration level

Usage Guidelines

A wireless device does not receive and send data all the time. An interval between data receiving and sending improves transmission performance. This interval is called GI.

The GI mode consists of the short interval and common interval. The common interval is 800 ns whereas the short interval is 400 ns. The short interval is applicable to 802.11n specifications, which can raise the transmission rate of 802.11n packets.

NOTE:

The guard-interval-mode command supports only 802.11ac and 802.11n.

Example

# Set the GI mode of radio profile 80211n to normal.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] radio-profile name 80211n  
[Huawei-wlan-radio-prof-80211n] guard-interval-mode normal 

a-msdu send enable

Function

The a-msdu send enable command enables the function of sending 802.11 frames in A-MSDU mode.

The undo a-msdu send enable command disables the function of sending 802.11 frames in A-MSDU mode.

By default, the function of sending 802.11 frames in A-MSDU mode is disabled.

Format

a-msdu send enable

undo a-msdu send enable

Parameters

None

Views

Radio profile view

Default Level

2: Configuration level

Usage Guidelines

Usage Scenario

Aggregated MAC Service Data Unit (A-MSDU) technology aggregates multiple MAC Service Data Units (MSDU)s into an MAC Protocol Data Unit (MPDU), which reduces MAC layer costs of the 802.11 packets and improves packet transmission efficiency especially when short MSDUs are aggregated.

Follow-up Procedure

Run the commit { all | ap ap-id } command to deliver the configuration to APs.

Precautions

The function of sending 802.11 frames in A-MSDU mode can only be enabled on the 802.11ac radio.

Example

# Enable the function of sending 802.11 frames in A-MSDU mode.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] radio-profile name radio
[Huawei-wlan-radio-prof-radio] a-msdu send enable

a-msdu send max-subframes

Function

The a-msdu send max-subframes command sets the maximum number of subframes that can be aggregated into an A-MSDU at one time.

The undo a-msdu send max-subframes command restores the default maximum number of subframes that can be aggregated into an A-MSDU at one time.

By default, a maximum of two subframes can be aggregated into an A-MSDU at one time.

Format

a-msdu send max-subframes max-subframe-count

undo a-msdu send max-subframes

Parameters

Parameter

Description

Value

max-subframe-count

Specifies the maximum number of subframes that can be aggregated into an A-MSDU at one time.

The value is an integer ranging from 2 to 15.

Views

Radio profile view

Default Level

2: Configuration level

Usage Guidelines

Usage Scenario

A-MSDU technology aggregates multiple MSDUs into an MPDU, which reduces MAC layer costs of the 802.11 packets.
  • When the wireless network quality is satisfactory, increase the maximum number of subframes that can be aggregated into an A-MSDU at one time to improve the network usage efficiency and wireless service performance.
  • When the wireless network quality is unsatisfactory or delay-sensitive services, such as voice services are transmitted, reduce the maximum number of subframes that can be aggregated into an A-MSDU at one time to minimize the impact of packet loss on services and reduce packet transmission delay. Some STAs have restrictions on the number of subframes aggregated into a received A-MSDU. If the number of subframes sent by the AP exceeds the threshold, the STAs cannot receive the frames properly.

Prerequisite

The function of sending 802.11 frames in A-MSDU mode has been enabled using the a-msdu send enable command.

Follow-up Procedure

Run the commit { all | ap ap-id } command to deliver the configuration to APs.

Precautions

The function of sending 802.11 frames in A-MSDU mode can only be enabled on the 802.11ac radio.

Example

# Set the maximum number of subframes that can be aggregated into an A-MSDU at one time to 2.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] radio-profile name radio
[Huawei-wlan-radio-prof-radio] a-msdu send enable
[Huawei-wlan-radio-prof-radio] a-msdu send max-subframes 2
Related Topics

ac sysnetid

Function

The ac sysnetid command configures the NE name of an AC.

The undo ac sysnetid command deletes the NE name of an AC.

By default, no NE name is configured for an AC.

Format

ac sysnetid ac-sysnetid

undo ac sysnetid

Parameters

Parameter

Description

Value

ac-sysnetid

Specifies the NE name of an AC.

The value is a string of 1 to 32 case-sensitive characters without spaces or question marks (?). The value can contain digits, letters, and special characters such as the asterisk (*) and number sign (#).

Views

WLAN view

Default Level

2: Configuration level

Usage Guidelines

Usage Scenario

The administrator can run the ac sysnetid command to configure a unique NE name for an AC. This facilitates AC management.

Configuration Impact

If you run the ac sysnetid command multiple times, only the latest configuration takes effect.

Example

# Set the NE name of an AC to ABC123.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ac sysnetid ABC123

access-user syslog-restrain enable

Function

The access-user syslog-restrain enable command enables system log suppression.

The undo access-user syslog-restrain enable command disables system log suppression.

By default, system log suppression is enabled.

Format

access-user syslog-restrain enable

undo access-user syslog-restrain enable

Parameters

None

Views

System view

Default Level

2: Configuration level

Usage Guidelines

After a STA passes authentication or successfully associates with the AP, the AP sends system logs to the NMS server. A system log contains MAC addresses of the STA, AC, and AP, AP and AC name and current time, and authentication result.

If a STA fails to associate with an AP or fails authentication, the STA attempts to go online continuously. The AP sends a large number of duplicate logs to the AC in a short period, which wastes resources and deteriorates system performance. To prevent this problem, enable system log suppression.

Example

# Enable system log suppression.

<Huawei> system-view
[Huawei] access-user syslog-restrain enable

access-user syslog-restrain period

Function

The access-user syslog-restrain period command sets the period of system log suppression.

By default, the period of system log suppression is 300s.

Format

access-user syslog-restrain period period

Parameters

Parameter

Description

Value

period

Specifies the period of system log suppression.

The value is an integer that ranges from 60 to 604800, in seconds.

Views

System view

Default Level

2: Configuration level

Usage Guidelines

When a STA is authenticated or successfully associates with an AP, the AP sends system logs to the NMS server. A system log contains MAC addresses of the STA, AP, and AC, AP name and current time, AC name and current time, and authentication result.

A STA retries continuously after it fails to associate with an AP or pass the authentication. When this occurs, the AC sends a large number of logs in a short time. This results in a high statistics failure rate and degrades the NMS performance. The system log suppression function reduces impact of such logs on the NMS.

Example

# Set the period of system log suppression to 600s.

<Huawei> system-view
[Huawei] access-user syslog-restrain period 600

antenna-gain

Function

The antenna-gain command changes the antenna gain of a specific type of APs.

The undo antenna-gain command restores the default antenna gain of a specific type of APs.

The default antenna gain of a specific type of APs is 0 dB.

Format

antenna-gain antenna-gain [ radio radio ]

undo antenna-gain [ radio radio ]

Parameters

Parameter

Description

Value

antenna-gain

Specifies the antenna gain.

The value is an integer that ranges from 0 to 30, in dB.

radio radio

Specifies the radio.

The value is an integer that ranges from 0 to 3.
  • 0: indicates the 2.4 GHz radio.
  • 1: indicates the 5 GHz radio.
  • 2: Reserved.
  • 3: Reserved.

Views

AP type view

Default Level

2: Configuration level

Usage Guidelines

The antenna gain is the ratio of the power density produced by an antenna to the power density that should be obtained at the same point if the power accepted by the antenna were radiated equally. It can measure the capability for an antenna to receive and send signals in a specified direction, which is one of the most important parameters to select a BTS antenna. In the same condition, if the antenna gain is high, the wave travels far.

The attributes of the default AP type cannot be modified.

Example

# Set the antenna gain of AP type ap200 whose ID is 213 to 30.
<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap-type id 213 type ap200
[Huawei-wlan-ap-type-ap200] antenna-gain 30

antenna-gain (radio view)

Function

The antenna-gain command configures the antenna gain of an AP radio.

The undo antenna-gain command restores the default antenna gain of an AP radio.

By default, the antenna gain of an AP radio is determined by the country code, AP type, and working frequency of the radio.

Format

antenna-gain antenna-gain

undo antenna-gain

Parameters

Parameter

Description

Value

antenna-gain

Specifies the antenna gain.

The value is an integer, in dB. The value range varies according to AP models.

Views

Radio view

Default Level

2: Configuration level

Usage Guidelines

The antenna gain is the ratio of the power density produced by an antenna to the power density that should be obtained at the same point if the power accepted by the antenna were radiated equally. It can measure the capability for an antenna to receive and send signals in a specified direction, which is one of the most important parameters to select a BTS antenna. In the same condition, if the antenna gain is high, the wave travels far.

Example

# Set the antenna gain of radio 0 of AP 0 to 4.
<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap 0 radio 0
[Huawei-wlan-radio-0/0] antenna-gain 4

ap

Function

The ap command adds an AP offline or displays the AP view.

The undo ap command deletes an AP.

By default, the system does not create an AP offline.

Format

ap id ap-id [ { type-id type-id | ap-type ap-type } { mac ap-mac [ static-ip ip-address ] | sn ap-sn } * ]

undo ap { id apid-list | all }

Parameters

Parameter

Description

Value

ap-id

Specifies the AP ID.

The value is an integer that ranges from 0 to 15.

apid-list

Specifies the AP ID.

The value is a string of 1 to 255 characters. When multiple APs are selected, use commas (,) or hyphens (-) to separate AP IDs. For example, 5,8,10-13,20 indicates the list of APs with IDs 5, 8, 10, 11, 12, 13, and 20.

type-id type-id

Specifies the AP type ID.

The value is an integer that ranges from 0 to 255.

ap-type ap-type

Specifies the AP type.

The value is a string of 1 to 31 characters.

mac ap-mac

Specifies the MAC address of an AP.

The value is in H-H-H format. An H is a hexadecimal number of four digits. The value cannot be a broadcast or a multicast MAC address.

sn ap-sn

Specifies the serial number of an AP.

The value is a string of 1 to 63 characters consisting only of letters and digits.

static-ip ip-address

Specifies the IP address for an AP.

The value is in dotted decimal notation.

Views

WLAN view

Default Level

2: Configuration level

Usage Guidelines

  • After an AP is added, you can set parameters for the AP offline. When the AP goes online automatically, it is configured according to parameters set offline.
  • When adding an AP, ensure that you enter the AP type ID; otherwise, you will enter the AP view.
  • When adding an AP, the input varies as follows:
    • If the current unauthorized AP detection policy is MAC address detection, enter only the MAC address when adding an AP.
    • If the current unauthorized AP detection policy is SN detection, only enter the SN when adding an AP.
    • If the current detection policy requires no authentication, enter the MAC address or SN.
  • The system adds the new AP into the current default region, binds the default profile, and distributes a default description. The format is ap-x, and x specifies the AP ID.
  • When entering the AP view, enter the AP ID only; otherwise, an AP is added.
NOTE:
Running this command will configure the static IP address of the AP.
  • If the AP attempts to obtain an IP address in DHCP mode, it sends a DHCP Discovery packet to the DHCP server to obtain its IP address. The DHCP server allocates the IP address to the AP from the IP address pool. In this case, the AP can go online only when the allocated IP address is consistent with the configured static IP address.
  • If the AP obtains the IP address in static mode but the configured static IP address is inconsistent with that on the AC, the AP cannot go online. Only when the two IP addresses are the same, the AP can go online.

Example

# Create an AP with ID 1, type ID 19, and MAC address 0025-9e07-8270.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap id 1 type-id 19 mac 0025-9e07-8270

# Enter AP view 1.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap id 1
[Huawei-wlan-ap-1]  

ap alarm-restriction enable

Function

The ap alarm-restriction enable command enables alarm suppression for an AP.

The undo ap alarm-restriction command disables alarm suppression for an AP.

By default, alarm suppression is enabled for an AP.

Format

ap alarm-restriction enable

undo ap alarm-restriction

Parameters

None

Views

AP profile view

Default Level

2: Configuration level

Usage Guidelines

If a STA cannot go online due to security type mismatch or access user upper limit exceeding, the STA will automatically re-connect to the AP. During this period, the AP sends a large number of STA association failure alarms to the AC, which degrades the system performance.

To solve this problem, enable alarm suppression for the AP. Then the AP does not report alarms repeatedly in the alarm suppression period, preventing alarm storms.

Example

# Enable alarm suppression for an AP.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap-profile name huawei
[Huawei-wlan-ap-prof-huawei] ap alarm-restriction enable
Related Topics

ap alarm-restriction period

Function

The ap alarm-restriction period command configures the period of alarm suppression on an AP.

The undo ap alarm-restriction period command restores the default period of alarm suppression for an AP.

The default alarm suppression period is 60 seconds on an AP.

Format

ap alarm-restriction period time

undo ap alarm-restriction period

Parameters

Parameter Description Value

time

Specifies the period of alarm suppression for an AP. The value is an integer that ranges from 10 to 300, in seconds.

Views

AP profile view

Default Level

2: Configuration level

Usage Guidelines

You can run the ap alarm-restriction period command to configure the period of alarm suppression for an AP. The AP reports an alarm only one time in the specified period if the alarm is repeatedly generated.

Example

# Set the period of alarm suppression to 200 seconds for an AP.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap-profile name huawei
[Huawei-wlan-ap-prof-huawei] ap alarm-restriction period 200
Related Topics

ap data-collection interval

Function

The ap data-collection interval command sets the data buffer duration.

The undo ap data-collection interval command restores the default data buffer duration.

By default, an AC buffers AP data for 5 minutes.

Format

ap data-collection interval time-value

undo ap data-collection interval

Parameters

Parameter

Description

Value

time-value

Specifies the buffer duration.

The value is an integer that ranges from 5 to 60, in minutes.

Views

WLAN view

Default Level

2: Configuration level

Usage Guidelines

You can run the ap collect-time command to enable an AC to buffer AP data and set the buffer duration.

Example

# Enable an AC to buffer AP data and set the buffer duration.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap data-collection enable
[Huawei-wlan-view] ap data-collection interval 57

ap modify

Function

The ap modify command changes the MAC address or serial number (SN) of a specified AP.

You can run the display ap (for AC) command to view the MAC address and SN of a specified AP.

Format

ap modify ap-id { mac ap-mac | sn ap-sn } *

Parameters

Parameter

Description

Value

ap-id

Specifies the ID of the AP to be replaced.

The value is an integer that ranges from 0 to 15.

mac ap-mac

Specifies the MAC address of the new AP.

The value is in H-H-H format. An H is a hexadecimal number of four digits. The value cannot be a broadcast or a multicast MAC address.

sn ap-sn

Specifies the SN of the new AP.

The value is a string of 1 to 63 characters and can contain only letters and digits.

Views

WLAN view

Default Level

2: Configuration level

Usage Guidelines

To replace an AP without configuring the new AP, you can change the MAC address or SN of the original AP to that of the new AP. The new AP goes online using the original ID, and original configurations take effect on the new AP.

Example

# Change the MAC address and SN of AP 0 to 0002-1110-0120 and SN000008 of the new AP.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap modify 0 mac 0002-1110-0120 sn SN000008 
  Warning: Modify AP will influence the service that has published in AP, Whethe
r to continue? [Y/N]y  
Related Topics

ap radio

Function

The ap radio command displays the radio view based on the specified AP ID or radio ID.

Format

ap ap-id radio radio-id

Parameters

Parameter

Description

Value

ap-id

Specifies the AP ID.

The value is an integer that ranges from 0 to 15.

radio-id

Specifies the radio ID. The radio ID range depends on the AP type and the maximum number of radios configured for the AP type.

The value is an integer that ranges from 0 to 3.
  • 0: indicates the 2.4 GHz radio.
  • 1: indicates the 5 GHz radio.
  • 2: Reserved.
  • 3: Reserved.

Views

WLAN view

Default Level

2: Configuration level

Usage Guidelines

  • Configure the radio in the radio view displayed based on the AP ID and radio ID.
  • Create a VAP by binding a service set in this view. A VAP is a functional entity on an AP. VAPs created on radios on an AP can be different from each other. After the configuration is committed using the commit command, the AP can provide users with services based on the parameters delivered by the VAP.

Example

# Display the radio view.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap 0 radio 0 
[Huawei-wlan-radio-0/0]  

ap static-ip

Function

The ap static-ip command configures AP IP addresses to be checked during CAPWAP tunnel establishment in batches.

The undo ap static-ip command deletes the configured IP addresses in batches.

By default, no AP IP addresses to be checked during CAPWAP tunnel establishment in batches is configured.

Format

ap static-ip ap-id apid-list start-ip ip-address

undo ap static-ip ap-id apid-list

Parameters

Parameter

Description

Value

ap-id apid-list

Specifies the AP ID.

The value is a string of 1 to 255 characters. When multiple APs are selected, use commas (,) or hyphens (-) to separate AP IDs. For example, 5,8,10-13,20 indicates the list of APs with IDs 5, 8, 10, 11, 12, 13, and 20.

start-ip ip-address

Specifies the start IP address.

The value is in dotted decimal notation.

Views

WLAN view

Default Level

2: Configuration level

Usage Guidelines

This command configures IP addresses to be checked during CAPWAP tunnel establishment. An AP can go online only when the IP address obtained by the AP during CAPWAP tunnel establishment is the same as that in the command.

This command differs from the static-bind ip-address ip-address mac-address mac-address command in that:
  • the static-bind ip-address ip-address mac-address mac-address command assigns a specified IP address to the DHCP client and the DHCP client can use the assigned IP address to go online.
  • the ap static-ip ap-id apid-list start-ip ip-address command configures the AP IP address to be checked during CAPWAP tunnel establishment. The AP can go online only when the IP address to be checked is the same as that obtained by the AP during CAPWAP tunnel establishment.

For example, if you configure the IP addresses of AP0, AP1, and AP2 to be checked respectively as 10.2.2.100, 10.2.2.101, and 10.2.2.102 but AP0, AP1, and AP2 do not obtain these IP addresses during CAPWAP tunnel establishment, the APs cannot go online.

Example

# Configure IP addresses for AP 0 to AP 2 in batches. The start IP address is 10.2.2.100.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap static-ip ap-id 0,1,2 start-ip 10.2.2.100 
Warning: This operation maybe cause ap reset, continue?[Y/N]:y  
Related Topics

ap sysnetid

Function

The ap sysnetid command configures the NE name of an AP.

The undo ap sysnetid command deletes the NE name of an AP.

By default, no NE name is configured for an AP.

Format

ap sysnetid ap-sysnetid

undo ap sysnetid

Parameters

Parameter

Description

Value

ap-sysnetid

Specifies the NE name of an AP.

The value is a string of 1 to 32 case-sensitive characters without spaces or question marks (?). The value can contain digits, letters, and special characters such as the asterisk (*) and number sign (#).

Views

AP view

Default Level

2: Configuration level

Usage Guidelines

Usage Scenario

The administrator can run the ap sysnetid command to configure a unique NE name for an AP. This facilitates AP management.

Configuration Impact

If you run the ap sysnetid command multiple times in the same AP view, only the latest configuration takes effect.

Example

# Set the NE name of an AP to ABC123.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap id 0
[Huawei-wlan-ap-0] ap sysnetid ABC123

ap-auth-mode

Function

The ap-auth-mode command configures the AP authentication mode.

The undo ap-auth-mode command restores the default AP authentication mode.

The default AP authentication mode is MAC address authentication.

Format

ap-auth-mode { mac-auth | no-auth | sn-auth }

undo ap-auth-mode

Parameters

Parameter

Description

Value

mac-auth

Indicates the MAC address authentication mode.

-

no-auth

Indicates the non-authentication mode.

-

sn-auth

Indicates the SN authentication mode.

-

Views

WLAN view

Default Level

2: Configuration level

Usage Guidelines

After the ap-auth-mode command is executed, the AC authenticates the AP using the configured mode.

When a confirmed AP exists in the system, you cannot change the AP authentication mode.

The non-authentication mode brings security risks. You are advised to set the authentication mode to MAC address authentication or SN authentication, which is more secure.

Example

# Change the AP authentication mode to MAC address authentication.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap-auth-mode mac-auth

# Restore the default AP authentication mode.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] undo ap-auth-mode                                                             
Related Topics

ap-blacklist mac

Function

The ap-blacklist mac command adds specified MAC addresses to the AP blacklist.

The undo ap-blacklist mac command removes specified MAC addresses from the AP blacklist.

By default, no AP blacklist is configured.

Format

ap-blacklist mac ap-mac1 [ to ap-mac2 ]

undo ap-blacklist mac ap-mac1 [ to ap-mac2 ]

Parameters

Parameter

Description

Value

ap-mac1

Specifies the MAC address of an AP.

The value is in H-H-H format. An H is a hexadecimal number of 4 digits.

to ap-mac2

Specifies the end MAC address. This parameter is used when you want to add multiple MAC addresses to the blacklist. It must be larger than ap-mac1. Parameters ap-mac1 and ap-mac2 identify an AP MAC range. A maximum of 128 MAC addresses can be added to the blacklist in batches.

The value is in H-H-H format. An H is a hexadecimal number of 4 digits.

Views

WLAN view

Default Level

2: Configuration level

Usage Guidelines

Usage Scenario

If the AP's MAC address is in the blacklist, the AP cannot go online. If the MAC address of an online AP is in the blacklist, the AP is forced to log out.

Precautions

The AP blacklist and whitelist can be configured at the same time. However, the MAC address of an AP cannot be added to the AP blacklist and whitelist at the same time.

If AP whitelist and blacklist are all configured, check whether an AP is on the blacklist first.

Example

# Add the AP with the MAC address of 0025-9e07-8280 to the AP blacklist.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap-blacklist mac 0025-9e07-8280

# Add MAC addresses from 0025-9e07-8270 to 0025-9e07-8276 to the AP blacklist.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap-blacklist mac 0025-9e07-8270 to 0025-9e07-8276

ap data-collection enable

Function

The ap data-collection enable command enables an AC to buffer AP data.

The undo ap data-collection enable command restores the default settings.

By default, an AC is disabled from buffering AP data and buffers AP data for 5 minutes.

Format

ap data-collection enable

undo ap data-collection enable

Parameters

None

Views

WLAN view

Default Level

2: Configuration level

Usage Guidelines

The NMS needs to periodically query performance statistics (including AP and radio performance statistics and information about users on an AP) from an AC that queries the information from the AP.

Data caching is a method to improve query performance, in which an AC periodically queries performance statistics and caches the data. When the NMS requires the data, the NMS queries the data from the buffer but not from the AP.

You are advised to enable an AC to buffer AP data when you use the NMS to query AP statistics. When NMS query expires, the NMS can obtain AP data from the AC.

Example

# Enable an AC to buffer AP data.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap data-collection enable

# Disable an AC from buffering AP data.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] undo ap data-collection enable

ap-confirm

Function

The ap-confirm command confirms unauthenticated APs.

Format

ap-confirm { all | { mac ap-mac | sn ap-sn } [ id ap-id ] }

Parameters

Parameter

Description

Value

all

Confirms all APs.

-

id ap-id

Specifies the AP ID.

The value is an integer that ranges from 0 to 15.

mac ap-mac

Specifies the MAC address of an AP.

The value is in H-H-H format. An H is a hexadecimal number of four digits.

sn ap-sn

Specifies the serial number of an AP.

The value is a string of 1 to 63 characters.

Views

WLAN view

Default Level

2: Configuration level

Usage Guidelines

After viewing unauthenticated APs using the display unauthorized-ap record command, you can run the ap-confirm command to confirm these unauthenticated APs if you want to connect them to the AC. After confirmation, APs are added to the default region and bound to the default AP profile.

Example

# Confirm the AP with MAC 0025-9e07-8270 and ID 1.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap-confirm mac 0025-9e07-8270 id 1

# Confirm all APs.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap-confirm all

ap-manufacturer-config (for AC)

Function

The ap-manufacturer-config command restores the factory settings of APs.

Format

ap-manufacturer-config id ap-id

Parameters

Parameter

Description

Value

id ap-id

Specifies the AP ID.

The value is an integer that ranges from 0 to 15.

Views

WLAN view

Default Level

2: Configuration level

Usage Guidelines

When a configuration error occurs on the AP, you can run this command to clear AP configurations.

After restoring factory settings, the AP is reset and configurations are restored to factory settings.

Example

# Restore the factory settings of AP 0.
<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap-manufacturer-config id 0
Warning: Reset AP to the manufacturing default configuration, continue?[Y/N]:y
Info: Reset AP to the manufacturing default configuration successfully. 

ap-ping

Function

The ap-ping command uses a specified AP to ping a network device and displays the returned result.

Format

ap-ping id ap-id [ -c count | -s packetsize | -m time | -t timeout ] * host

Parameters

Parameter

Description

Value

id ap-id

Specifies the AP ID.

The value is an integer that ranges from 0 to 15.

-c count

Specifies the number of ICMP Echo Request packets to be sent.

The value is an integer that ranges from 1 to 10. The default value is 4.

-s packetsize

Specifies the length of an Echo Request packet excluding the IP header and ICMP header.

The value is an integer that ranges from 20 to 8100, in bytes. The default value is 56 bytes.

-m time

Specifies the time to wait before sending the next ICMP Request packet.

The value is an integer that ranges from 1 to 5000, in milliseconds. The default value is 2000 ms.

-t timeout

Specifies the timeout period for an ICMP Echo Response packet.

The value is an integer that ranges from 0 to 10000, in milliseconds. The default value is 2000 ms.

host

Specifies the domain name or IP address of the destination host.

The value is a string of 1 to 20 characters.

Views

All views

Default Level

2: Configuration level

Usage Guidelines

  • You can run this command to check the connectivity between an AP and network device by pinging a network device from an AP.
  • The prerequisite is that the AP is online and has been configured with an IP address.
NOTE:
  • This command may cost much time because the parameters such as waiting time affects the command running.
  • Only one AP can perform the ping operation at a time.

Example

# Ping a network device from AP 1.

<Huawei> ap-ping id 1 192.168.100.242
Warning: This operation maybe takes several minutes, continue?[Y/N]:y
<Huawei>                         
  AP ping result                                                                
    Success count        : 4                                                    
    Failure count        : 0                                                    
    Average response time: 2 ms                                                 
    Minimum response time: 2 ms                                                 
    Maximum response time: 4 ms  

ap-profile

Function

The ap-profile command creates or enters an AP profile view.

The undo ap-profile command deletes an AP profile view.

By default, the system creates AP profile ap-profile-0. The ID is 0.

Format

ap-profile { id profile-id | name profile-name } *

undo ap-profile { id profile-id | name profile-name }

Parameters

Parameter

Description

Value

id profile-id

Specifies the ID of an AP profile.

The value is an integer that ranges from 0 to 15.

name profile-name

Specifies the name of an AP profile.

The value is a string of 1 to 31 characters. The value cannot contain question marks (?) or spaces and cannot start or end with double quotation marks (" ").

Views

WLAN view

Default Level

2: Configuration level

Usage Guidelines

  • After adding an AP profile, you can bind the AP to this profile or run the default-ap-profile command to specify this profile as the default profile. Subsequent automatically-detected APs are bound to this profile.
  • When adding an AP profile, enter the profile name and do not enter the profile ID. Otherwise, you enter the AP profile view. A new AP profile contains default configurations.
  • In the AP profile view, you can enter only the profile index or the profile name, or enter both the profile index and name.
  • The system default profile, current default profile, and a profile bound to an AP cannot be deleted.

Example

# Create AP profile ap-profile-new.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap-profile name ap-profile-new
[Huawei-wlan-ap-prof-ap-profile-new]

# Enter the view of AP profile 2.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap-profile id 2 
[Huawei-wlan-ap-prof-abc]

ap-region

Function

The ap-region command creates an AP region or enters the AP region view.

The undo ap-region command deletes an AP region.

By default, the system creates AP region 0.

Format

ap-region id region-id

undo ap-region id region-id

Parameters

Parameter

Description

Value

id region-id

Specifies the AP region ID.

The value is an integer that ranges from 0 to 15.

Views

WLAN view

Default Level

2: Configuration level

Usage Guidelines

Usage Scenario

Adjusting the radio channel and power of an AP may lead to adjustment of another AP. To quicken adjustment, minimize the impact, and reduce the workload, all the APs accessing the same AC can be divided into several regions. The impact of adjustment on an AP is limited within the local region.

After creating AP regions, run the region-id command to specify the AP region that each AP belongs to. The radio channels and power of the APs in the same region will be adjusted uniformly.

After creating an AP region, you can add existing APs to this region or run the default-ap-region command to configure this region as the default region. Automatically discovered APs are added to the default AP region.

Precautions

  • The default AP region with ID 0 cannot be deleted.
  • The current default AP region cannot be deleted.
  • An AP region containing APs cannot be deleted.

Example

# Add AP region 1 and enter the AP region view.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap-region id 1
[Huawei-wlan-ap-region-1]

ap-region merge

Function

The ap-region merge command merges two AP regions.

Format

ap-region merge region-id1 into region-id2

Parameters

Parameter

Description

Value

region-id1

Specifies the ID of a merged AP source region.

The value is an integer that ranges from 0 to 15.

region-id2

Specifies the ID of a merged AP destination region.

The value is an integer that ranges from 0 to 15.

Views

WLAN view

Default Level

2: Configuration level

Usage Guidelines

Usage Scenario

You can run this command to merge two AP regions. After AP region merging, all APs in the source region join the destination region, and the source region becomes an empty region.

Prerequisites

The AP IDs exist both in the source and destination regions. (To create an AP region, run the ap-region command.)

Example

# Merge AP region 0 to AP region 7.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap-region merge 0 into 7 

ap-region-name

Function

The ap-region-name command changes the name of an AP region.

The undo ap-region-name command default the default name of a region.

By default, the AP region name is ap-region-region-id.

Format

ap-region-name region-name

undo ap-region-name

Parameters

Parameter

Description

Value

region-name

Specifies the AP region name.

The value is a string of 1 to 63 characters. The value cannot contain question marks (?) or spaces and cannot start or end with double quotation marks (" ").

Views

AP region view

Default Level

2: Configuration level

Usage Guidelines

Usage Scenario

You can run the ap-region-name command to change the name of an AP region.

Prerequisites

An AP region exists. (To create an AP region, run the ap-region command.)

Example

# Change the name of AP region 0 to ap-region-00.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap-region id 0
[Huawei-wlan-ap-region-0] ap-region-name ap-region-00   
Related Topics

ap-reset (for AC)

Function

The ap-reset command resets an AP.

Format

ap-reset { all | id ap-id | ap-type { type ap-type | type-id type-id } }

Parameters

Parameter

Description

Value

all

Indicates all APs.

-

id ap-id

Specifies the AP ID.

The AP ID must exist.

ap-type

Indicates the AP type.

-

type-id type-id

Specifies the AP type ID.

The AP type ID must exist.

type ap-type

Specifies the AP type.

The AP type must exist.

You can run the display ap-type all command to view types of all APs.

Views

WLAN view

Default Level

2: Configuration level

Usage Guidelines

Usage Scenario

You can run this command when an AP finishes upgrading online.

Prerequisites

An AP exists on the AC.

Example

# Reset AP 1.
<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap-reset id 1
Warning: Reset AP(s), continue?[Y/N]:y                                             

ap-sysname (for AC)

Function

The ap-sysname command changes the system name of an AP.

The undo ap-sysname command restores the default system name of an AP.

By default, the system name of an AP is ap-ap-id.

Format

ap-sysname ap-sysname

undo ap-sysname

Parameters

Parameter

Description

Value

ap-sysname

Specifies the system name of an AP.

The value is a string of 1 to 31 characters. The value cannot contain question marks (?) or spaces and cannot start or end with double quotation marks (" ").

Views

AP view

Default Level

2: Configuration level

Usage Guidelines

You can run the ap-sysname command to change the AP system name or restore the default name.

Example

# Change the system name of AP 1 to ap_01.
<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap id 1 
[Huawei-wlan-ap-1] ap-sysname ap_01                                        
Related Topics

ap-type

Function

The ap-type command adds an AP type or enters an AP type view.

The undo ap-type command deletes an AP type.

Format

ap-type { id type-id | type ap-type } *

undo ap-type { id type-id | type ap-type }

Parameters

Parameter

Description

Value

id type-id

Specifies the AP type ID.

The value is an integer that ranges from 0 to 255.
NOTE:
When an AP type is added, the value ranges from 200 to 255.

type ap-type

Specifies the AP type.

The value is a string of 1 to 31 characters. The value cannot contain question marks (?) or spaces and cannot start or end with double quotation marks (" "). The value must start with Ap, aP or ap.

Views

WLAN view

Default Level

2: Configuration level

Usage Guidelines

  • You can run the ap-type command to add an AP type.
  • APs of an AP type can go online only after the type is added.
NOTE:

When adding an AP type, specify the type name ap-type.

You can run the display ap-type all command to view AP types preset in the system. By default, the system supports the preset AP types.

Example

# Add AP type AP6010DN-AGN and enter the AP type view.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap-type type AP6010DN-AGN
[Huawei-wlan-ap-type-AP6010DN-AGN]   

# Enter the type view of AP 1. (Assume that the type of AP 1 is AP6010DN-AGN.)

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap-type id 1
[Huawei-wlan-ap-type-AP6010DN-AGN]    

ap-update update-filename ap-type

Function

The ap-update update-filename command configures the upgrade file name for APs of a specified type.

The undo ap-update update-filename command deletes the upgrade file name for APs of a specified type.

Format

ap-update update-filename filename ap-type type-id

undo ap-update update-filename ap-type type-id

Parameters

Parameter

Description

Value

type-id

Specifies the AP type ID.

The value is an integer that ranges from 0 to 255.

filename

Specifies the AP upgrade file name.

The value is a string of 1 to 255 case-sensitive characters. Ensure that the file name is the same as the actual upgrade file name and has the extension .bin.

Views

WLAN view

Default Level

2: Configuration level

Usage Guidelines

Run the ap-update multi-load ap-type command to upgrade APs of the same type in batches.

Example

# Set the upgrade file name for APs with the type ID 10 to new.bin.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap-update update-filename new.bin ap-type 10   

ap-update ftp-server

Function

The ap-update ftp-server command configures basic FTP information, including the FTP server IP address, and FTP client user name and password.

The undo ap-update ftp-server command restores default FTP settings.

By default, the FTP server IP address is 255.255.255.255, the FTP client user name is anonymous, and the FTP client password is anonymous@huawei.com.

Format

ap-update ftp-server server-ip-address [ ftp-username ftp-username ] [ ftp-password cipher ftp-password ]

undo ap-update ftp-server

Parameters

Parameter

Description

Value

server-ip-address

Specifies an IP address for the FTP server.

The value is in dotted decimal notation.

ftp-username ftp-username

Specifies the FTP client user name.

The value is a string of 1 to 31 characters. The value cannot contain question marks (?) or spaces and cannot start or end with double quotation marks (" "). The default value is anonymous.

ftp-password

Indicates the password for logging in to the FTP server.

-

cipher

Indicates the password in cipher text.

-

ftp-password

Specifies the FTP client password.

The value is a string of characters without question marks (?) or spaces. It cannot start or end with double quotation marks (" "). ftp-password can be up to 68 characters in cipher text, such as %@%@N!}w4F\6;42P$A2'XqkP(Ix6%@%@. ftp-password also can be a string of 1 to 31 characters in plain text, such as huawei123.

Views

WLAN view

Default Level

2: Configuration level

Usage Guidelines

  • The FTP configuration is used when the automatic upgrade and online upgrade modes are FTP. In the automatic upgrade or online upgrade, the AC sends basic FTP information to the AP, and the AP requests the FTP server for upgrade based on FTP information.
  • Run the ap-update multi-load command to load upgrade software package in batches.

APs do not support the following characters:". Ensure that the FTP client user name and unencrypted password configured on the AC do not contain the preceding characters. Otherwise, FTP upgrade fails.

Example

# Configure the FTP server IP address, and FTP client user name and password.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap-update ftp-server 192.168.1.100 ftp-username admin ftp-password cipher wlanadmin

ap-update multi-load ap-type

Function

The ap-update multi-load command upgrades APs of the same type in batches.

The undo ap-update multi-load command cancels batch upgrade of APs with the same type.

Format

ap-update multi-load ap-type type-id [ ap-id { ap-id-start [ to ap-id-end ] } &<1-10> ]

undo ap-update multi-load ap-type type-id [ ap-id { ap-id-start [ to ap-id-end ] } &<1-10> ]

Parameters

Parameter

Description

Value

type-id

Specifies the AP type ID.

The value is an integer that ranges from 0 to 255.

ap-id ap-id-start

Specifies the start AP ID.

The value is an integer that ranges from 0 to 15.

NOTE:
The value of ap-id-start must be smaller than that of ap-id-end.
to ap-id-end

Specifies the end AP ID.

The value is an integer that ranges from 0 to 15.

NOTE:
The value of ap-id-end must be larger than that of ap-id-start.

Views

WLAN view

Default Level

2: Configuration level

Usage Guidelines

Usage Scenario

You can run this command to upgrade APs of the same type in batches in the online upgrade mode.

If the type of the AP specified by ap-id differs from that specified by type-id, the AP cannot be upgraded.

If the type of the AP specified by ap-id differs from that specified by type-id, the AP cannot be upgraded.

Prerequisites

AP upgrade files have been configured in batches using the ap-update update-filename command.

Follow-up Procedure

Run the ap-update multi-reset command to reset APs in batches to make AP upgrade take effect.

Precautions

The undo ap-update multi-load ap-type type-id command cancels batch upgrade of APs with the same type. However, if the AP system software has been written to the flash memory during the upgrade, the command does not take effect.

Example

# Upgrade APs with type-id 19 in batches online.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap-update multi-load ap-type 19
Warning: Do not power off the AP during the upgrade.
# Upgrade APs with IDs 1, 5 to 7 and 9 in batches and specify type-id of the APs as 19.
<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap-update multi-load ap-type 19 ap-id 1 5 to 7 9
Warning: Do not power off the AP during the upgrade.

ap-update multi-reset ap-type

Function

The ap-update multi-reset command resets APs of the same type in batches.

Format

ap-update multi-reset ap-type type-id [ ap-id { ap-id-start [ to ap-id-end ] } &<1-10> ]

Parameters

Parameter

Description

Value

type-id

Specifies the AP type ID.

The value is an integer that ranges from 0 to 255.

ap-id ap-id-start

Specifies the start AP ID.

The value is an integer that ranges from 0 to 15.

NOTE:
The value of ap-id-start must be smaller than that of ap-id-end.
to ap-id-end

Specifies the end AP ID.

The value is an integer that ranges from 0 to 15.

NOTE:
The value of ap-id-end must be larger than that of ap-id-start.

Views

WLAN view

Default Level

2: Configuration level

Usage Guidelines

This command resets APs of the same type in batches and can be used only after APs are upgraded in batches.

If the type of the AP specified by ap-id differs from that specified by type-id, the AP cannot be reset.

If the type of the AP specified by ap-id differs from that specified by type-id, the AP cannot be reset.

Example

# Reset APs with type-id 19 in batches.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap-update multi-reset ap-type 19   
# Reset APs with IDs 1, 5 to 7 and 9 in batches and specify type-id of the APs as 19.
<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap-update multi-reset ap-type 19 ap-id 1 5 to 7 9

ap-update ftp-server max-connect-num

Function

The ap-update ftp-server max-connect-num command sets the maximum number of APs that can be upgraded simultaneously in FTP mode.

The undo ap-update ftp-server max-connect-num command restores the default maximum number of APs that can be upgraded simultaneously in FTP mode.

By default, a maximum of 50 APs can be upgraded simultaneously in FTP mode.

Format

ap-update ftp-server max-connect-num max-connect-number

undo ap-update ftp-server max-connect-num

Parameters

Parameter

Description

Value

max-connect-number

Specifies the maximum number of APs that can be upgraded simultaneously.

The value is an integer that ranges from 5 to 16.

Views

WLAN view

Default Level

2: Configuration level

Usage Guidelines

Usage Scenario

When APs are upgraded in FTP mode, you can configure the value of max-connect-number to change the maximum number of APs that can be upgraded simultaneously.
  • If the number of APs to be upgraded is equal to or smaller than max-connect-number, all APs can be upgraded simultaneously.

  • If the number of APs to be upgraded is larger than max-connect-number, only the specified number of APs can be upgraded simultaneously. After the specified number of APs are upgraded, the remaining APs are upgraded automatically until all APs are upgraded. The number of APs that are upgraded at a time cannot exceed the value of max-connect-number.

Precautions

An external FTP server can be used, which is recommended. The AC can also function as the FTP server.
  • When an external FTP server is used, the maximum number of APs that can be upgraded simultaneously is the configured max-connect-number.
  • If an AC is used as the FTP server, a maximum of fifteen APs can be upgraded simultaneously even if the specified number is larger than fifteen.

    When the AC functions as the FTP server, run the ap-update ftp-server max-connect-num max-connect-number command to set the maximum number of APs that can be upgraded simultaneously. The value of max-connect-number is an integer ranging from 5 to 15. During the upgrade, a maximum of 5 to 15 APs can be upgraded at a time until all APs are upgraded. If the configured number of APs to be upgraded simultaneously is larger than 15, an error message will be displayed after the first 15 APs are upgraded. The remaining APs cannot be automatically upgraded. You have to repeat the command until all APs are upgraded.

Example

# Set the maximum number of APs that can be upgraded simultaneously in FTP mode to 5.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap-update ftp-server max-connect-num 5

ap-whitelist mac

Function

The ap-whitelist mac command adds a specified AP MAC address to the AP whitelist.

The undo ap-whitelist mac command deletes an AP MAC address from the AP whitelist.

By default, no AP whitelist is configured.

Format

ap-whitelist mac ap-mac1 [ to ap-mac2 ]

undo ap-whitelist mac ap-mac1 [ to ap-mac2 ]

Parameters

Parameter

Description

Value

ap-mac1

Specifies the AP MAC address.

The value is in H-H-H format. An H is a hexadecimal number of four digits.

to ap-mac2

Specifies the end MAC address. This parameter is used when you want to add multiple MAC addresses to the whitelist. The value must be larger than ap-mac1. ap-mac1 and ap-mac2 identify a range.

The value is in H-H-H format. An H is a hexadecimal number of four digits.

Views

WLAN view

Default Level

2: Configuration level

Usage Guidelines

When the AP authentication mode is set to MAC address authentication using the ap-auth-mode command, if the MAC address of an online AP exists in the whitelist, the AP is automatically added to the AC. If the MAC address of an AP is not in the whitelist, the AP can go online only after its identity is confirmed by the user using the ap-confirm command.

Example

# Add AP MAC address 0025-9e07-8280 to the whitelist.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap-whitelist mac 0025-9e07-8280

# Add the MAC addresses from 0025-9e07-8270 to 0025-9e07-8290 to the AP whitelist.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap-whitelist mac 0025-9e07-8270 to 0025-9e07-8290

ap-whitelist sn

Function

The ap-whitelist sn command adds an AP with a specified serial number (SN) to the AP whitelist.

The undo ap-whitelist sn command deletes the SN of an AP from the AP whitelist.

By default, no AP whitelist is configured.

Format

ap-whitelist sn ap-sn1 [ to ap-sn2 ]

undo ap-whitelist sn ap-sn1 [ to ap-sn2 ]

Parameters

Parameter

Description

Value

ap-sn1

Specifies the SN of an AP.

The value is a string of 1 to 63 characters.

to ap-sn2

Specifies the end SN. This parameter is used when you want to add multiple SNs to the whitelist. It must be larger than ap-sn1. ap-sn1 and ap-sn2 identify a range.

The value is a string of 1 to 63 characters.

Views

WLAN view

Default Level

2: Configuration level

Usage Guidelines

Usage Scenario

When the AP authentication mode is set to SN authentication using the ap-auth-mode command, if the SN of an online AP exists in the whitelist, the AP is automatically added to the AC. If the SN of an AP is not in the whitelist, the AP can go online only after its identity is confirmed by the user using the ap-confirm command.

Precautions

When adding multiple SNs to the whitelist, ensure that the start SN length and the end SN length are the same.

Example

# Add SN 08PE56430071 to the AP whitelist.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap-whitelist sn 08PE56430071

# Add SNs from 08PE56430076 to 08PE56430081 to the AP whitelist.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap-whitelist sn 08PE56430076 to 08PE56430081

association-timeout (for AC)

Function

The association-timeout command configures an association aging time for STAs.

The undo association-timeout command restores the default association aging time.

By default, the association aging time is 5 minutes.

Format

association-timeout association-timeout

undo association-timeout

Parameters

Parameter

Description

Value

association-timeout

Specifies the association aging time of STAs.

The value is an integer that ranges from 1 to 30, in minutes.

Views

Service set view

Default Level

2: Configuration level

Usage Guidelines

The administrator can run the association-timeout command to set the association aging time for STAs. If the AP receives no data packet from a STA in a specified time, the STA goes offline after the association aging time expires.

Example

# Create a service set named ChinaNet and set the association aging time of STAs to 15 minutes.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] service-set name ChinaNet 
[Huawei-wlan-service-set-ChinaNet] association-timeout 15       

authentication static-user

Function

The authentication static-user command configures an AP as a non-authentication terminal.

The undo authentication static-user command deletes an AP that is configured as a non-authentication terminal.

By default, no AP is configured as a non-authentication terminal.

Format

authentication static-user mac-address vlan-id

undo authentication static-user mac-address vlan-id

Parameters

Parameter

Description

Value

mac-address

Specifies the MAC address of an AP.

The value is in H-H-H format. An H is a hexadecimal number of four digits.

vlan-id

Specifies the management VLAN of an AP.

The value is an integer that ranges from 1 to 4094.

Views

GE interface view, Ethernet interface view

Default Level

2: Configuration level

Usage Guidelines

When both wired terminals and APs exist in the LAN that is connected to a physical interface on the AC, if 802.1x authentication, MAC address authentication, and portal authentication are enabled on the interface, the AC considers APs as wired terminals and authenticates APs. Therefore, APs cannot connect to the AC. To solve this problem, the administrator can run the authentication static-user command to configure APs as non-authentication terminals. Then APs can connect to the AC without any authentication.

NOTE:
Layer 3 Ethernet interfaces including Layer 3 logical interfaces do not support this command. Interfaces involved in this command refers to Layer 2 Ethernet interfaces.

Example

# Configure the AP with the MAC address 286E-D42B-0CE5 and management VLAN 800 as a non-authentication terminal.

<Huawei> system-view
[Huawei] interface ethernet 0/0/1
[Huawei-Ethernet2/0/0] authentication static-user 286E-D42B-0CE5 800

available-antenna-number (for AC)

Function

The available-antenna-number command sets the number of available antennas on a radio.

The undo available-antenna-number command restores the default number of available antennas on a radio.

By default, all antennas on a radio are available.

Format

available-antenna-number { all | available-antenna-number }

undo available-antenna-number

Parameters

Parameter

Description

Value

all

Indicates that all antennas are available.

-

available-antenna-number

Specifies the number of available antennas.

The value is an integer and the value range varies according to the AP type.

Views

Radio view

Default Level

2: Configuration level

Usage Guidelines

  • The value of available antennas must be equal to or smaller than the number of antennas on a radio.
  • You can run this command to shut down excess antennas to save power.

Example

# Set the number of available antennas on a radio to 1.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap 0 radio 0 
[Huawei-wlan-radio-0/0] available-antenna-number 1   

batch ap

Function

The batch ap command adds multiple virtual access points (VAPs) at a time.

The undo batch ap command deletes multiple virtual access points (VAPs) at a time.

By default, no VAP is created in the system.

Format

batch ap { ap-id [ to ap-id ] } &<1-10> radio { radio-id [ to radio-id ] } &<1-4> { service-set { service-set-id [ to service-set-id ] } &<1-16> | radio-profile { id profile-id | name profile-name } } *

undo batch ap { ap-id [ to ap-id ] } &<1-10> radio { radio-id [ to radio-id ] } &<1-4> [ service-set [ service-set-id [ to service-set-id ] &<1-16> ] | radio-profile ]

Parameters

Parameter

Description

Value

ap-id

Specifies the AP ID.

The value is an integer that ranges from 0 to 15.

radio radio-id

Specifies the radio ID.

The value is an integer that ranges from 0 to 3.

service-set service-set-id

Specifies the service set ID.

The value is an integer that ranges from 0 to 15.

radio-profile id profile-id

Specifies the radio profile ID.

The value is an integer ranging from 0 to 15.

radio-profile name profile-name

Specifies the radio profile name.

The value must be an existing radio profile name.

Views

WLAN view

Default Level

2: Configuration level

Usage Guidelines

  • To create multiple VAPs at a time, run the batch ap command.
  • To delete multiple VAPs at a time, run the undo batch ap command.

When two or more users log in to the device at the same time, you are advised not to add VAPs in batches.

Example

# Add multiple VAPs.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] batch ap 3 to 4 radio 0 to 1 service-set 4 to 7
Related Topics

beacon-interval (for AC)

Function

The beacon-interval command sets the interval for sending Beacon frames.

The undo beacon-interval restores the default interval for sending Beacon frames.

By default, the interval for sending Beacon frames is 100 ms.

Format

beacon-interval beacon-interval

undo beacon-interval

Parameters

Parameter

Description

Value

beacon-interval

Specifies the interval for sending Beacon frames.

The value is an integer that ranges from 20 to 1000, in ms.

Views

Radio profile view

Default Level

2: Configuration level

Usage Guidelines

An AP broadcasts Beacon frames at intervals to notify STAs of an existing 802.11 network. After receiving a Beacon frame, a STA can modify parameters used to connect to the 802.11 network.

A long interval for sending Beacon frames lengthens the dormancy time of STAs, while a short interval for sending Beacon frames increases air interface costs. Therefore, you are advised to set the interval for sending Beacon frames for an AP based on the VAP quantity. The following intervals for sending Beacon frames are recommended for APs with different VAP quantities on a single radio:
  • No more than 4 VAPs: about 100 ms
  • 5 to 8 VAPs: about 200 ms
  • 9 to 12 VAPs: about 300 ms
  • 13 to 16 VAPs: about 400 ms

Example

# Set the interval for sending Beacon frames to 200 ms in the radio profile named 802.11b.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] radio-profile name 80211b
[Huawei-wlan-radio-prof-80211b] beacon-interval 200   

capwap control-link-priority

Function

The capwap control-link-priority command configures the priority of CAPWAP management packets.

The undo capwap control-link-priority command restores the default priority of CAPWAP management packets.

By default, the priority of CAPWAP management packets is 7.

Format

capwap control-link-priority { local | remote } priority-value

undo capwap control-link-priority { local | remote }

Parameters

Parameter

Description

Value

local

Indicates the priority of CAPWAP management packets from an AC to an AP. The priority of CAPWAP management packets determines the reliability of the link between an AC and an AP.

-

remote

Indicates the priority of CAPWAP management packets from an AP to an AC. The priority of CAPWAP management packets determines the reliability of the link between an AP and an AC.

-

priority-value

Specifies the priority of CAPWAP management packets.

The value is an integer that ranges from 0 to 7. The value 0 indicates the lowest priority, and the value 7 indicates the highest priority.
NOTICE:
Configure priority 4 to 7 for CAPWAP management packets from an AC to an AP, preventing the CAPWAP management tunnel from being interrupted due to large traffic.

Views

System view

Default Level

2: Configuration level

Usage Guidelines

You can use the capwap control-link-priority command to configure the DSCP priority of CAPWAP management packets. A higher priority indicates a more reliable link between the AC and AP.

The configuration of the priority of CAPWAP management packets from an AC to an AP takes effect immediately. After the priority of CAPWAP management packets from an AP to an AC is changed, if the AP is online, the priority is sent to the AP in the Echo packet. If the AP is not online, the priority is delivered to the AP in the Echo packet when the AP goes online. The new priority takes effect once the AP receives it.

Example

# Set the priority of CAPWAP management packets from an AC to an AP to 6.

<Huawei> system-view
[Huawei] capwap control-link-priority local 6

capwap dtls psk

Function

The capwap dtls psk command configures a pre-shared key used for DTLS encryption.

The undo capwap dtls psk command deletes a pre-shared key used for DTLS encryption.

By default, the pre-shared key used for DTLS encryption is huawei_seccwp.

Format

capwap dtls psk psk-value

undo capwap dtls psk

Parameters

Parameter

Description

Value

psk-value

Specifies the pre-shared key used for DTLS encryption.

The value is string of characters. The pre-shared key contains 32 or 68 characters in cipher text, for example, %@%@0}C:XR6Y.Uh\6*Qi8bz,ey:R%@%@, or contains 6 to 32 characters in plain text, for example, a1234567. The password must contain at least two types of the following: uppercase letters (A to Z), lowercase letters (a to z), digits, and special characters except the question mark (?) and space.

Views

System view

Default Level

2: Configuration level

Usage Guidelines

Application Scenario

During the CAPWAP tunnel establishment between an AP and an AC, the AP performs a DTLS session with the AC as soon as the AP is associated with the AC. DTLS supports PSK encryption. When the pre-shared key is used for DTLS encryption, the dtls psk command can be used to manually change the value in the DTLS session on the AC.
NOTE:
It is recommended that you change the pre-shared key in a timely manner to ensure device security.

Follow-up Procedure

Run the capwap dtls control-link encrypt command to enable the function of encrypting the CAPWAP control tunnel using Datagram Transport Layer Security (DTLS).

Configuration Precautions

After the configuration is complete, the new pre-shared key will be automatically synchronized to online APs. However, the old pre-shared key takes effect on the APs. The new pre-shared key takes effect only after the APs goes offline and goes online again.

Example

# Configure the pre-shared key for DTLS encryption as z0020011@11.

<Huawei> system-view
[Huawei] capwap dtls psk z0020011@11

capwap dtls psk-mandatory-match enable

Function

The capwap dtls psk-mandatory-match enable command enables an AP to establish a Datacom Transport Layer Security (DTLS) session with an AC using the default pre-shared key.

The undo capwap dtls psk-mandatory-match enable command disables an AP to establish a Datacom Transport Layer Security (DTLS) session with an AC using the default pre-shared key.

By default, an AP is enabled to establish a DTLS session with an AC using the default pre-shared key.

Format

capwap dtls psk-mandatory-match enable

undo capwap dtls psk-mandatory-match enable

Parameters

None.

Views

System view

Default Level

2: Configuration level

Usage Guidelines

When a new AP is added to the WLAN or the passwords of the AP and AC are different (for example, the password of the AC is changed but the AP is not online), you can enable the AP to perform DTLS sessions with the AC using the default pre-shared key. After three DTLS session failures, the AP notifies the AC of DTLS sessions using the default pre-shared key. In this way, a CAPWAP tunnel is established between the AP and the AC.

Example

# Enable the AP to establish a DTLS session with the AC using the default pre-shared key.

<Huawei> system-view
[Huawei] capwap dtls psk-mandatory-match enable

capwap keep-alive

Function

The capwap keep-alive command sets the CAPWAP heartbeat detection interval and the number of CAPWAP heartbeat detections.

The undo capwap keep-alive command restores the default CAPWAP heartbeat detection interval and the number of CAPWAP heartbeat detections.

By default, the CAPWAP heartbeat detection interval is 25s and the number of CAPWAP heartbeat detections is 6.

If dual-link backup is enabled, the CAPWAP heartbeat detection interval is 25s and the number of CAPWAP heartbeat detections is 3.

Format

capwap keep-alive { interval interval-value | times times-value } *

undo capwap keep-alive { interval | times }

Parameters

Parameter

Description

Value

interval interval-value

Specifies the CAPWAP heartbeat detection interval, the interval at which two detection packets are sent.

The value is an integer ranging from 3 to 300, in seconds.

times times-value

Specifies the number of CAPWAP heartbeat detections. If no response is received after the specified number of times, the link is considered disconnected.

The value is an integer ranging from 2 to 120.

Views

System view

Default Level

2: Configuration level

Usage Guidelines

As defined by CAPWAP, an AP and an AC send handshake packets periodically to maintain the data channel and management channel. If the AP does not receive packets from the AC within the heartbeat detection interval, it considers that the link between them is disconnected. Then the AP resets and releases its IP address, and reestablishes a link. If the AC does not receive packets from the AP within the heartbeat detection interval, it disconnects the link between the AC and the AP and reports an error message to the AP.

NOTE:

If dual-link backup is enabled, the CAPWAP heartbeat detection interval is 25s and the number of CAPWAP heartbeat detections is 3. When the Wireless Distribution System (WDS) is required in dual-link backup configuration, the WDS link may be unstable and users may not access the network. You need to run this command to set the interval for CAPWAP heartbeat detection to 25 seconds and the number of CAPWAP heartbeat detections to 6.

After the CAPWAP heartbeat detection interval and the number of CAPWAP heartbeat detections are configured, the interval and the number of times for sending Echo and Keepalive packets are configured.

If you set the CAPWAP heartbeat detection interval and the number of CAPWAP heartbeat detections smaller than the default values, the CAPWAP link reliability is degraded. Exercise caution when you set the values. The default values are recommended.

Example

# Set the CAPWAP heartbeat detection interval to 30s and the number of CAPWAP heartbeat detections to 3.

<Huawei> system-view
[Huawei] capwap keep-alive interval 30 times 3

capwap source interface

Function

The capwap source interface command configures the source interface used by the AC to establish a CAPWAP tunnel with .

The undo capwap source interface command deletes the configured AC source interface.

By default, no AC source interface is configured.

Format

capwap source interface { loopback loopback-number | vlanif vlan-id }

undo capwap source interface

Parameters

Parameter

Description

Value

loopback loopback-number

Configures a loopback interface as the source interface.

The loopback interface must exist.

vlanif vlan-id

Configures a VLANIF interface as the source interface.

The VLANIF interface must exist.

Views

System view

Default Level

2: Configuration level

Usage Guidelines

Usage Scenario

An AC uses the IP address of the specified interface as the source IP address. All APs connected to the AC can learn this IP address and use the IP address to communicate with the AC.

Prerequisites

An IP address has been assigned to the specified loopback or VLANIF interface.

Example

# Configure a loopback interface as the source interface.

<Huawei> system-view
[Huawei] interface loopback 20
[Huawei-LoopBack20] ip address 192.168.10.1 24
[Huawei-LoopBack20] quit
[Huawei] capwap source interface loopback 20
Related Topics

capwap source ip-address

Function

The capwap source ip-address command configures the source IP address for an AC.

The undo capwap source ip-address command deletes the source IP address of an AC.

By default, no source IP address is configured for an AC.

Format

capwap source ip-address ip-address

undo capwap source ip-address

Parameters

Parameter

Description

Value

ip-address

Specifies a source IP address for an AC.

The value is in dotted decimal notation.

Views

System view

Default Level

2: Configuration level

Usage Guidelines

Usage Scenario

An AC uses a unique source IP address. All APs connected to the AC can learn the source IP address and use the IP address to communicate with the AC.

  • When AC hot standby is implemented using VRRP, two ACs constitute a virtual AC. All APs connected to the two ACs communicate with the virtual AC. You must run the capwap source ip-address command to specify the virtual IP address as the source IP address of the virtual AC.
  • When APs are managed by an AC, run the capwap source ip-address command to specify the IP address of a VLANIF or loopback interface as the AC's source IP address.

Prerequisites

A VRRP group has been created and a virtual IP address has been specified for the group using the vrrp vrid virtual-ip command, or an IP address has been configured for the VLANIF interface or the loopback interface.

Precautions

If the virtual IP address has been configured, you cannot run the capwap source interface command to configure the source IP address for the AC.

Example

# Configure the source IP address of the AC as 10.10.10.10.

<Huawei> system-view
[Huawei] vlan batch 100
[Huawei] interface vlanif 100
[Huawei-Vlanif100] vrrp vrid 1 virtual-ip 10.10.10.10
[Huawei-Vlanif100] quit
[Huawei] capwap source ip-address 10.10.10.10

channel (for AC)

Function

The channel command configures a channel for a radio.

The undo channel command restores the default channel of a radio.

The default working channel of a radio is selected based on the country code and radio frequency band.
  • The radio frequency band varies according to AP models.
  • The default working channel of each AP radio varies according to different country codes.

You can run the display actual channel-power (for AC) command to check the channel in use on a radio.

Format

channel { 20mhz | 40mhz-minus | 40mhz-plus | 80mhz } channel

undo channel

Parameters

Parameter

Description

Value

20mhz

Indicates that the channel bandwidth is 20 MHz.

-

40mhz-minus

Indicates that the channel bandwidth is 40 MHz Minus.

-

40mhz-plus

Indicates that the channel bandwidth is 40 MHz Plus.

-

80mhz
Indicates that the channel bandwidth is 80 MHz.
NOTE:
Only the 5 GHz radio of the AP2030DN, AP4030DN, AP4130DN, AP7030DE, AP8030DN, AP8130DN, AP5030DN and AP5130DN supports this parameter.

-

channel

Specifies the working channel for a radio. The channel is selected based on the country code and radio mode.

The parameter is an enumeration value. The value range is determined according to the country code and radio mode.

Views

Radio view

Default Level

2: Configuration level

Usage Guidelines

Usage Scenario

Different radios use different channels. Channels for radios also vary in different countries and regions. Select channels based on the actual situations.

NOTE:
  • The configured channel IDs must match the radio frequency band. For details about mappings between channel IDs and frequency bands, see Country codes & Channels compliance status.

  • The 2.4 GHz radio does not support the 40 MHz Minus, 40 MHz Plus and 80 MHz bandwidth in FCC compliance regions (including America).

  • The channels you configure must be supported by the terminals; otherwise, the terminals cannot discover wireless signals. For example, when the country code is set to China, 5 GHz channels 36, 40, 44, 48, 52, 56, 60, and 64 can be configured. However, most terminals do not support these channels currently. If these channels are configured, the terminals cannot discover wireless signals. In this case, you can configure 5 GHz channels 149, 153, 157, 161, and 165, which are supported by the terminals.

  • If an AP detects radar signals on a channel, the channel cannot be configured as the radio channel of the AP in 30 minutes. However, the channel can be configured as the radio channel of other APs not detecting radar signals on it.

Prerequisites

The channel mode has been set to fixed using the channel-mode fixed command.

Example

# Configure the channel for radio 0/0 as 6.
<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap 0 radio 0
[Huawei-wlan-radio-0/0] channel 20mhz 6    

channel-mode (for AC)

Function

The channel-mode command sets the channel mode in a radio profile.

The undo channel-mode command restores the default channel mode in a radio profile.

By default, the channel of a radio can be automatically adjusted.

Format

channel-mode { auto | fixed }

undo channel-mode

Parameters

Parameter

Description

Value

auto

Indicates the automatic mode, in which the channels of radios bound to the radio profile can be automatically adjusted.

-

fixed

Indicates the fixed mode, in which radios bound to the radio profile use fixed channels.

-

Views

Radio profile view

Default Level

2: Configuration level

Usage Guidelines

Two channel working modes are available:
  • Automatic mode: Channels are automatically selected to adapt to the radio environment.
  • Fixed mode: Channels must be manually specified for radios.

The automatic mode is recommended because you do not need to specify a channel for each radio. The fixed mode provides an alternative way. You can use this mode if you want to avoid frequent channel adjustment, which may cause intermittent service interruption.

If an AP needs radio calibration, the channel mode must be set to automatic mode in the AP's radio profile.

Example

# Set the channel mode in radio profile 802.11b to automatic mode.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] radio-profile name 80211b
[Huawei-wlan-radio-prof-80211b] channel-mode auto       

clear unauthorized-ap record

Function

The clear unauthorized-ap record command clears information about unauthenticated APs.

Format

clear unauthorized-ap record

Parameters

None

Views

WLAN view

Default Level

2: Configuration level

Usage Guidelines

Usage Scenario

You can run this command to clear information about unauthenticated APs so that removed APs or unauthenticated APs that are physically disconnected from the AC can be cleared. This facilitates collecting statistics and confirmation of unauthenticated APs.

Precautions

If an AP physically connects to the AC but has not been authenticated, the AP is added in the unauthenticated AP list after you run the clear unauthorized-ap record command.

Example

# Clear information about unauthenticated APs.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] clear unauthorized-ap record
Warning: Clear unauthorized AP record, continue?[Y/N]:y

commit

Function

The commit command commits configurations of a specified AP or all APs.

Format

commit { all | ap ap-id }

Parameters

Parameter

Description

Value

all

Commits configurations of all APs.

-

ap ap-id

Commits configurations of a specified AP.

The value is an integer that ranges from 0 to 15.

Views

WLAN view

Default Level

2: Configuration level

Usage Guidelines

You can configure attributes for APs on the AC. The configurations are delivered to APs only after you run the commit command to commit the configurations.

NOTE:

If you commit configurations to a large number of APs simultaneously, some of the APs may fail to receive the configurations. In this case, you are advised to commit the configurations again.

Example

# Commit the configuration of a specified AP.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] commit ap 10
Warning: Committing configuration may cause service interruption, continue?[Y/N]
:y

# Commit configurations of all APs.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] commit all
Warning: Committing configuration may cause service interruption, continue?[Y/N]
:y

conflict-rate-threshold (for AC)

Function

The conflict-rate-threshold command sets the collision rate threshold in a radio profile.

The undo conflict-rate-threshold command restores the default collision rate threshold in a radio profile.

By default, the collision rate threshold is 60.

Format

conflict-rate-threshold conflict-rate-threshold

undo conflict-rate-threshold

Parameters

Parameter

Description

Value

conflict-rate-threshold

Specifies the collision rate threshold.

The value is an integer that ranges from 20 to 80, in percentage (%).

Views

Radio profile view

Default Level

2: Configuration level

Usage Guidelines

If the MAC layer of a radio does not receive any ACK packet after sending a packet at the lowest rate, a collision occurs.

The collision rate threshold and the packet loss ratio threshold determine whether the radio environment is good. When the collision rate or packet loss ratio of a radio reaches the threshold, the system considers that the radio environment deteriorates. When this occurs, the system may start radio calibration or take measures to avoid signal interference.

Example

# Set the collision rate threshold to 70% in radio profile 802.11b.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] radio-profile name 80211b
[Huawei-wlan-radio-prof-80211b] conflict-rate-threshold 70

cpu warn-threshold

Function

The cpu warn-threshold command sets the CPU usage alarm threshold.

The undo cpu warn-threshold command restores the default CPU usage alarm threshold.

By default, the CPU usage alarm threshold is 90.

Format

cpu warn-threshold threshold-num

undo cpu warn-threshold

Parameters

Parameter

Description

Value

threshold-num

Specifies the CPU usage alarm threshold.

The value is an integer that ranges from 50 to 100.

Views

AP view

Default Level

2: Configuration level

Usage Guidelines

You can run the cpu warn-threshold command to set the CPU usage alarm threshold. The threshold is delivered to the specified AP. An alarm is reported when the AP CPU usage exceeds the threshold. The alarm is cleared when the AP CPU usage falls below the threshold.

Example

# Set the CPU usage alarm threshold of AP 0 to 60.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap id 0
[Huawei-wlan-ap-0] cpu warn-threshold 60

# Restore the CPU usage alarm threshold of AP 0 to the default value 90.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap id 0
[Huawei-wlan-ap-0] undo cpu warn-threshold

dai enable

Function

The dai enable command enables dynamic ARP inspection (DAI).

The undo dai enable command disables DAI.

By default, DAI is disabled.

Format

dai enable

undo dai enable

Parameters

None

Views

Service set view

Default Level

2: Configuration level

Usage Guidelines

DAI allows an AP to detect the ARP Request and Reply packets transmitted on the VAPs of the AP, to discard invalid and attack ARP packets, and to send an alarm to the connected AC. This function prevents ARP packets of unauthorized users from accessing the external network through the AP, protecting authorized users against interference or spoofing, and protecting the AP.

  • Invalid ARP packets: The source IP and MAC addresses of ARP Request and Reply packets do not match.
  • Attack ARP packets: When an AP receives a large number of consecutive ARP packets and the number of ARP packets exceeds the ARP attack alarm threshold, an ARP attack occurs.

Example

# Enable DAI.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] service-set name test 
[Huawei-wlan-service-set-test] dai enable  

default-ap-profile

Function

The default-ap-profile command configures an AP profile as the default AP profile.

The undo default-ap-profile command restores the original default AP profile of the system.

The default AP profile is ap-profile-0, and the ID is 0.

Format

default-ap-profile { id profile-id | name profile-name }

undo default-ap-profile

Parameters

Parameter

Description

Value

id profile-id

Specifies the ID of an AP profile.

The AP profile ID must exist.

name profile-name

Specifies the name of an AP profile.

The AP profile name must exist.

Views

WLAN view

Default Level

2: Configuration level

Usage Guidelines

APs that go online automatically are bound to the specified default AP profile.

Before configuring an AP profile as the default AP profile, ensure that the AP profile exists.

Example

# Configure the AP profile with the ID of 8 as the default AP profile.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] default-ap-profile id 8

# Configure the AP profile named profile-8 as the default AP profile.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] default-ap-profile name profile-8
Related Topics

default-ap-region

Function

The default-ap-region command changes the ID of the default AP region.

The undo default-ap-region command restores the original ID of the default AP region.

The default AP region ID is 0.

Format

default-ap-region id region-id

undo default-ap-region

Parameters

Parameter

Description

Value

region-id

Specifies the ID of the default AP region.

The value is an integer that ranges from 0 to 15.

Views

WLAN view

Default Level

2: Configuration level

Usage Guidelines

After the ID of the default AP region is changed, APs that go online automatically are added to the default AP region.

Before configuring an AP region as the default AP region, ensure that the AP region exists.

Example

# Configure AP region 8 as the default AP region.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] default-ap-region id 8   

# Restore the original default AP region.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] undo default-ap-region
Related Topics

deploy-mode

Function

The deploy-mode command configures the AP deployment mode in an AP region.

The undo deploy-mode command restores the default AP deployment mode.

The default deployment mode is normal-deploy.

Format

deploy-mode { densely-deploy | discrete-deploy | normal-deploy }

undo deploy-mode

Parameters

Parameter

Description

Value

densely-deploy

Indicates the dense mode. In this mode, APs in a region are densely located. To meet basic service requirements, each AP works with at least 25% of the maximum radio power.

-

discrete-deploy

Indicates the sparse mode. In this mode, APs in a region are sparsely located without any signal interference between each other. In this case, an AP is an independent region. However, if one region is created for each AP, the configuration workload is heavy. Therefore, a special region can be created as a solution to contain all APs. The attributes of these APs require no adjustment, and every AP can work with the greatest radio power.

-

normal-deploy

Indicates the common mode. In this mode, APs are loosely deployed in a region. To meet basic service requirements, each AP works with at least 50% of the maximum radio power.

-

Views

AP region view

Default Level

2: Configuration level

Usage Guidelines

  • The AP deployment mode in an AP region affects the radio power and channels of APs in the region. You can run the deploy-mode command to specify the AP deployment mode in a region.
  • If the signals of several neighboring APs interfere with each other, the radio channels and power of these APs need to be adjusted. Adjusting the radio channel and power of an AP may lead to the adjustment of another AP. To quicken adjustment, minimize the impact, and reduce the workload, all the APs accessing the same AC can be divided into several regions. The impact of adjustment on an AP is limited within the local region.
  • In discrete-deploy mode, APs in an AP region are sparsely located and do not interfere with each other. These APs always work with the highest power.
  • In normal-deploy mode, APs in an AP region are loosely located and slightly interfere with each other. These APs work with 50% of the maximum power.
  • In densely-deploy mode, APs in an AP region are close to each other and greatly interfere with each other. These APs work with 25% of the maximum power.
  • Before running the deploy-mode command, ensure that an AP region exists.

Example

# Set the AP deployment mode in AP region 7 to densely-deploy.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap-region id 7
[Huawei-wlan-ap-region-7] deploy-mode densely-deploy   

# Restore the default AP deployment mode in AP region 7.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] ap-region id 7
[Huawei-wlan-ap-region-7] undo deploy-mode     

description (WLAN-ESS interface view)

Function

The description command configures the description of a WLAN-ESS interface.

The undo description command restores the default description of a WLAN-ESS interface.

By default, the description of a WLAN-ESS interface contains the WLAN-ESS interface number. For example, the description of WLAN ESS 15 is "HUAWEI, AR Series, Wlan-Ess15 Interface".

Format

description description

undo description

Parameters

Parameter

Description

Value

description

Specify the description of the WLAN-ESS interface

The value is a string of 1 to 242 case-sensitive characters. Spaces are allowed.

Views

WLAN-ESS interface view

Default Level

2: Configuration level

Usage Guidelines

Usage Scenario

The description command is used to set the description of the WLAN-ESS interface, which is convenient for identifying, memorizing, and maintaining the WLAN-ESS interface.

You can run the display interface wlan-ess command to view the description of a WLAN-ESS interface.

Configuration Impact

If you run the description command multiple times in the same WLAN-ESS interface view, only the last configuration takes effect.

Precautions

The description of a WLAN-ESS interface must provide useful information.

Set different descriptions for WLAN-ESS interfaces to distinguish WLAN-ESS interfaces.

Example

# Set the description of WLAN-ESS interface 15 to VOICE.

<Huawei> system-view
[Huawei] interface wlan-ess 15
[Huawei-Wlan-Ess15] description VOICE

dhcp trust port

Function

The dhcp trust port command configures the DHCP trusted interface on an AP.

The undo dhcp trust port command cancels the configuration.

By default, the DHCP trusted interface is disabled on an AP in service set view but enabled in AP profile view.

Format

dhcp trust port

undo dhcp trust port

Parameters

None

Views

Service set view, AP profile view

Default Level

2: Configuration level

Usage Guidelines

If a bogus DHCP server is deployed at the user side, STAs may obtain incorrect IP addresses and network configuration parameters and cannot communicate properly. After the undo dhcp trust port command is executed in the service set view, an AP discards the DHCP OFFER, ACK, and NAK packets sent by the bogus DHCP server and reports to the AC about the IP address of the unauthorized DHCP server.

Before WLAN services are delivered to an AP, run the dhcp trust port command in the AP profile view. After the command is run, the AP receives the DHCP OFFER, ACK, and NAK packets sent by the authorized DHCP server and forwards the packets to STAs so that the STAs can obtain valid IP addresses and go online.

Example

# Create a service set named test and configure the DHCP trusted interface on an AP.

<Huawei> system-view
[Huawei] wlan ac
[Huawei-wlan-view] service-set name test 
[Huawei-wlan-service-set-test] dhcp trust port  

display wlan ac-global

Function

The display wlan ac-global command displays global system parameters.

Format

display wlan ac-global

Parameters

None

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

None

Example

# Display global system parameters.

<Huawei> display wlan ac-global
  ------------------------------------------------------------                  
  Country code       : CN                                                       
  Carrier ID         : Other company                                            
  AC ID              : 0                                                        
  AC Network Element : -                                                        
Table 12-1  Description of the display wlan ac-global command output
Item Description

Country code

Indicates the country code. For example, CN (China).

To configure a country code, run the wlan ac-global command.

AC ID

Indicates the AC ID.

To configure an AC ID, run the wlan ac-global command.

Carrier ID

Indicates the carrier ID, the value can be:
  • China mobile communications corporation (cmcc)
  • China telecom corporation (ctc)
  • China unicom corporation (cuc)
  • Other company

To configure a carrier ID, run the wlan ac-global command.

AC Network Element

Indicates the NE name of an AC.

To configure the NE name for an AC, run the ac sysnetid command.

Related Topics

display actual channel-power (for AC)

Function

The display actual channel-power command displays the channel and power of a radio.

Format

display actual channel-power { ap-id ap-id radio-id radio-id | all }

Parameters

Parameter

Description

Value

ap-id ap-id

Specifies an AP ID. The AP ID and radio ID identify a radio. To specify the AP ID, run the ap command.

The value is an integer that ranges from 0 to 15.

radio-id radio-id

Specifies the radio ID. The radio ID and AP ID identify a radio. To specify the radio ID, run the radio command.

The value is an integer that ranges from 0 to 3.

all

Displays the channels and power of all APs.

-

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

To view the channel used by a radio and power of the radio, run this command.

The power in the command output is the sum of the maximum transmit power of the radio interface and the antenna gain. If MIMO is supported, the MIMO gain should also be added. The maximum power displayed should comply with laws and regulations corresponding to the country code.

Example

# Display the channel and power of AP 1 radio 0.
<Huawei> display actual channel-power ap-id 1 radio-id 0 
  --------------------------------------------------------                      
   RADIO  CHANNEL POWER-LEVEL POWER(dBm) CHANNEL-BANDWIDTH                      
  --------------------------------------------------------                      
   1/0    9       0           20      20MHz                                  
  --------------------------------------------------------   
Table 12-2  Description of the display actual channel-power command output

Item

Description

RADIO

Radio identified by the AP ID and radio ID.

CHANNEL

Current channel of a radio. The current channel may be different from the configured channel before the configuration is committed.

POWER-LEVEL

Current transmit power level of a radio. The current transmit power level may be different from the configured transmit power level before the configuration is committed.

POWER(dBm)

Current transmit power of the radio, in dBm, which is determined by the power level.

CHANNEL-BANDWIDTH

Channel bandwidth.

display ap (for AC)

Function

The display ap command displays AP information.

Format

display ap { all | id ap-id | by-mac ap-mac | by-sn ap-sn | by-ipv4 ipv4-address | by-ssid ssid | by-state state }

Parameters

Parameter

Description

Value

all

Displays information about all APs, including the AP ID, AP type, AP profile ID, AP region ID, AP status, and total number of APs.
NOTE:
You can run the display ap-type command to check all AP types supported by the device.

-

id ap-id

Specifies the AP ID.

The value is an integer that ranges from 0 to 15.

by-mac ap-mac

Specifies the MAC address of an AP.

The value is in H-H-H format. An H is a hexadecimal number of four digits.

by-sn ap-sn

Specifies the SN of an AP.

The value is a string of 1 to 63 characters consisting only of letters and digits.

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

To view information about APs such as the AP ID, AP type, and AP profile ID, run this command.

Example

# Display information about all APs.

<Huawei> display ap all
  All AP information:                                                           
  Normal[4],Fault[0],Commit-failed[0],Committing[0],Config[0],Download[0]       
  Config-failed[0],Standby[0],Type-not-match[0],Ver-mismatch[0]
  ------------------------------------------------------------------------------
  AP    AP                    AP              Profile   AP              AP      
                                              /Region                           
  ID    Type                  MAC             ID        State           Sysname 
  ------------------------------------------------------------------------------
  0     AP6010DN-AGN          dcd2-fc21-5d40    0/0     normal          ap-0    
  1     AP6010DN-AGN          dcd2-fc9a-2110    0/0     normal          ap-1    
  2     AP6010DN-AGN          1047-80ac-cc60    0/0     normal          ap-2    
  3     AP6010DN-AGN          fc48-ef2d-3b00    0/0     normal          ap-3    
  ------------------------------------------------------------------------------
  Total number: 4,printed: 4
Table 12-3  Description of the display ap all command output

Item

Description

AP ID ID of an AP.
AP Type Type of an AP.
AP MAC MAC address of an AP.
Profile/Region ID AP profile ID and AP region ID.
AP State Status of an AP.
  • normal: The AP is in normal state.
  • type-not-match: The AP type is not supported by the AC.
  • fault: The AP fails.
  • config: The AP is initializing the configuration.
  • config-failed: The AP fails to initialize the configuration.
  • download: The AP is downloading the upgrade software.
  • committing: The WLAN service configuration is being committed.
  • commit-failed: The WLAN service configuration fails to be committed.
  • standby: The AP is in standby state on the standby AC.
  • ver-mismatch: The AP's version does not match the AC's.
AP Sysname

System name of an AP.

# Display information about AP 0.

<Huawei> display ap id 0
  AP 0 detail information:                                                      
  ------------------------------------------------------------------------------
  AP type ID: 21                                                                
  AP type: AP6310SN-GN                                                          
  AP profile ID: 0                                                              
  AP region ID: 0                                                               
  Sysname: ap-0                                                                 
  Keep-Service: Disable                                                         
  AP access priority mode: Normal Access                                        
  State: normal                                                                 
  AP MAC address: dcd2-fc9a-99e0                                                
  AP SN: 210235419810D1000045                                                   
  AP static IP address: -                                                       
  AP performance-statistic cycle: 15 minutes                                    
  AP System Network: -                                                          
  AP lineport total number: 1                                                   
  lineport MTU: 1800                                                            
  lineport MAC: dcd2-fc9a-99e0                                                  
  AP high temperature threshold(ºC):  55                                        
  AP low temperature threshold(ºC):  -15                                        
  AC priority: 0                                                                
  Protect ac IP address: -                                                      
  AP LLDP message-transmission delay time(s)   : 2                              
  AP LLDP message-transmission hold-multiplier : 4                              
  AP LLDP message-transmission interval time(s): 30                             
  AP LLDP restart delay time(s): 2                                              
  AP LLDP Admin Status: txrx                                                    
  AP LLDP report interval time(s): 30                                           
  AP Management VLAN: -                                                         
  Dynamic-blacklist : disable                                                   
  Dynamic-blacklist aging-duration(s) : 600                                     
  Attack detection flood interval(s) : 60                                       
  Attack detection flood times : 300                                            
  Attack detection psk interval(s) : 60                                         
  Attack detection psk times : 20                                               
  Flood attack detection quiet time(s)   : 600                                  
  Psk attack detection quiet time(s)     : 600                                  
  Weak iv attack detection quiet time(s) : 600                                  
  Spoof attack detection quiet time(s)   : 600                                  
  ------------------------------------------------------------------------------
Table 12-4  Description of the display ap id command output

Item

Description

AP type ID ID of the AP type.
AP type Type of an AP.
AP profile ID ID of the AP profile.
AP region ID ID of the region to which the AP belongs.
Sysname Name of an AP.
Keep-Service Whether the AP continues providing services after being disconnected from an AC.
  • enable: Service holding upon CAPWAP link disconnection is enabled.
  • disable: Service holding upon CAPWAP link disconnection is disabled.
AP access priority mode Access mode of a STA.
  • normal: Users select the SSID configured on a 2.4 GHz radio to access the AP.
  • 5g: Users select the SSID configured on a 5 GHz radio to access the AP.

To configure the access mode for a STA, run the access priority (for AC) command.

State Status of an AP.
  • normal: The AP is in normal state.
  • type-not-match: The AP type is not supported by the AC.
  • fault: The AP fails.
  • config: The AP is initializing the configuration.
  • config-failed: The AP fails to initialize the configuration.
  • download: The AP is downloading the upgrade software.
  • committing: The WLAN service configuration is being committed.
  • commit-failed: The WLAN service configuration fails to be committed.
  • standby: The AP is in standby state on the standby AC.
  • ver-mismatch: The AP's version does not match the AC's.
AP MAC address MAC address of an AP.
AP SN Serial number of an AP.
AP static IP address Static IP address of an AP.
AP performance-statistic cycle Interval at which performance statistics on an AP are collected, in minutes.
AP System Network NE ID of an AP.
AP lineport total number Number of wired interfaces on the AP.
AP lineport ID ID of a wired interface on the AP.
lineport description Description of a wired interface.
lineport type Type of a wired interface.
  • fe: 100M Ethernet interface
  • ge: 1000M Ethernet interface
  • gpon: Gigabit-capable passive optical network
  • epon: Ethernet passive optical network
  • adsl2plus
lineport speed Rate at a wired interface.
lineport MTU MTU on a wired interface.
lineport MAC MAC address on a wired interface.
AP high temperature threshold(°C) Temperature upper threshold of an AP.
AP low temperature threshold(°C) Temperature lower threshold of an AP.
AC priority Priority of an AC.
Protect ac IP address Standby AC IP address.
AP lineport mode Working mode of a wired interface.
  • root: The wired interface works in root mode.
  • endpoint: the wired interface works in endpoint mode.
AP lineport user-isolate Whether user isolation is enabled on a wired interface.
  • enable: User isolation is enabled on a wired interface.
  • disable: User isolation is disabled on a wired interface.
AP lineport PVID VLAN Default VLAN on a wired interface.
AP lineport vlan tagged Tagged VLAN on a wired interface.
AP lineport vlan untagged Untagged VLAN on a wired interface.
AP LLDP Whether LLDP is enabled on the AP.
  • enable: LLDP is enabled on the AP.
  • disable: LLDP is disabled on the AP.
AP LLDP Basic TLV Management Address Management address.
AP LLDP Basic TLV Port Description Interface description.
AP LLDP Basic TLV System Capability System capability.
AP LLDP Basic TLV System Description System description.
AP LLDP Basic TLV System Name System name.
AP LLDP message-transmission delay time(s) Delay in sending LLDP packets.
AP LLDP message-transmission hold-multiplier LLDP packets hold time multiplier.
AP LLDP message-transmission interval time(s) Interval for sending LLDP packets.
AP LLDP restart delay time(s) Reinitialization delay of the LLDP module.
AP LLDP Admin Status LLDP mode on the AP.
  • tx: The AP only sends but does not receive LLDP packets.
  • rx: The AP only receives but does not send LLDP packets.
  • txrx: The AP sends and receives LLDP packets.
AP LLDP report interval time(s) Interval for reporting neighbor information.
AP Management VLAN Management VLAN.
Dynamic-blacklist Whether to enable dynamic blacklist function.
Dynamic-blacklist aging-duration(s) Aging time of the dynamic blacklist.
Attack detection flood interval(s) Interval for flood attack detection.
Attack detection flood times Upper threshold for the number of packets of the same type received by an AP at an interval.
Attack detection psk interval(s) Interval for PSK attack detection.
Attack detection psk times Upper threshold for the number of failed authentications at an interval.
Flood attack detection quiet time(s) Quiet time of flood attack detection.
Psk attack detection quiet time(s) Quiet time of PSK attack detection.
Weak iv attack detection quiet time(s) Quiet time of weak IV attack detection.
Spoof attack detection quiet time(s) Quiet time of spoof attack detection.

display ap data-collection

Function

The display ap data-collection command displays the AP data buffer duration on an AC and status of the AP data buffering function.

Format

display ap data-collection

Parameters

None

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

You can run the display ap collect-time command to view the AP data buffer duration on an AC and status of the AP data buffering function.

Example

# Display the AP data buffer duration on an AC and status of the AP data buffering function.

<Huawei> display ap data-collection
AP data-collection: 5 minutes                                                   
Info: AP data-collection function switched off! 
Table 12-5  Description of the display ap data-collection command output

Item

Description

AP data-collection

Duration for buffering AP data on an AC.

display ap configurable channel (for AC)

Function

The display ap configurable channel command displays the configurable channels supported by a specified AP.

Format

display ap configurable channel [ ap-id ap-id | region-id region-id ]

Parameters

Parameter

Description

Value

ap-id ap-id

Specifies an AP ID.

The value is an integer that ranges from 0 to 15.

region-id region-id

Specifies an AP region ID.

The value is an integer that ranges from 0 to 15.

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

Different countries or regions use different wireless channels and powers. Setting country and area codes can specify channels that can be used on WLANs of different countries. The display ap configurable channel command displays the configurable channels supported by all APs or a specified AP.

Example

# Display the configurable channels supported by all APs.

<Huawei> display ap configurable channel
  2.4G 20M : 1,2,3,4,5,6,7,8,9,10,11,12,13.                                     
  2.4G 40M+: 1,2,3,4,5,6,7.                                                     
  2.4G 40M-: 5,6,7,8,9,10,11.                                                   
  5G   20M : 36,40,44,48,52,56,60,64,149,153,157,161,165.                       
  5G   40M+: 36,44,52,60,149,157.                                               
  5G   40M-: 40,48,56,64,153,161.                                               
  5G   80M : 36,40,44,48,52,56,60,64,149,153,157,161.
# Display the configurable channels supported by AP 1.
<Huawei> display ap configurable channel ap-id 1
  2.4G 20M : 1,2,3,4,5,6,7,8,9,10,11,12,13.                                     
  2.4G 40M+: 1,2,3,4,5,6,7.                                                     
  2.4G 40M-: 5,6,7,8,9,10,11.                                                   
  5G   20M : 36,40,44,48,52,56,60,64,149,153,157,161,165.                       
  5G   40M+: 36,44,52,60,149,157.                                               
  5G   40M-: 40,48,56,64,153,161.                                               
  5G   80M : 36,40,44,48,52,56,60,64,149,153,157,161.   
Table 12-6  Description of the display ap configurable channel command output

Item

Description

2.4G 20M

Channels configurable on an AP when the AP works on the 2.4 GHz frequency band in 802.11b/g/n mode. These channels work at a bandwidth of 20 MHz.

2.4G 40M+

Channels configurable on an AP when the AP works on the 2.4 GHz frequency band in 802.11n mode. These channels work at a bandwidth of 40 MHz.

2.4G 40M-

Channels configurable on an AP when the AP works on the 2.4 GHz frequency band in 802.11n mode. These channels work at a bandwidth of 40 MHz.

5G 20M

Channels configurable on an AP when the AP works on the 5 GHz frequency band in 802.11g/n mode. These channels work at a bandwidth of 20 MHz.

5G 40M+

Channels configurable on an AP when the AP works on the 5 GHz frequency band in 802.11n mode. These channels work at a bandwidth of 40 MHz.

5G 40M-

Channels configurable on an AP when the AP works on the 5 GHz frequency band in 802.11n mode. These channels work at a bandwidth of 40 MHz.

5G 80M

Channels configurable on an AP when the AP works on the 5 GHz frequency band in 802.11ac mode. These channels work at a bandwidth of 80 MHz.

Related Topics

display ap cpu warn-threshold

Function

The display ap cpu warn-threshold command displays the CPU usage alarm threshold on an AP.

Format

display ap id ap-id cpu warn-threshold

Parameters

Parameter

Description

Description

id ap-id

Specifies the AP ID.

The value is an integer that ranges from 0 to 15.

Views

All view

Default Level

1: Monitoring level

Usage Guidelines

None

Example

# Display the CPU usage alarm threshold on AP 0.

<Huawei> display ap id 0 cpu warn-threshold
Info: CPU threshold is 90%   
Related Topics

display ap around-ssid-list (for AC)

Function

The display ap around-ssid-list command displays SSIDs of neighbors of a specified AP.

Format

display ap id ap-id around-ssid-list

Parameters

Parameter

Description

Value

id ap-id

Specifies the AP ID.

The value is an integer that ranges from 0 to 15.

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

You can run this command to view SSIDs of neighbors of a specified AP. Neighbors of an AP include authorized and unauthorized neighbors. Authorized neighbors are other APs managed by the same AC. APs that are managed by other ACs are unauthorized neighbors.

Example

# Display SSIDs of neighbors of AP 0.

<Huawei> display ap id 0 around-ssid-list
  Own AP(2.4G):                                                                 
  ----------------------------------------------------                          
   SSID                                                                         
  ----------------------------------------------------                          
   huawei                                                                         
  ----------------------------------------------------                          
   Total: 1                                                                     
                                                                                
  Uncontrol AP(2.4G):                                                           
  ----------------------------------------------------                          
   SSID                                                                         
  ----------------------------------------------------                          
   huawei1                                                                  
   company                                                             
  ----------------------------------------------------                          
   Total: 2    
Table 12-7  Description of the display ap around-ssid-list command output
Item Description

Own AP(2.4G)

SSIDs of authorized neighbors.

Uncontrol AP(2.4G)

SSIDs of unauthorized neighbors.

display ap sta-signal strength

Function

The display ap sta-signal strength command displays the average signal strength of STAs connected to an AP.

Format

display ap id ap-id [ radio radio-id ] sta-signal strength

Parameters

Parameter

Description

Value

id ap-id

Specifies the AP ID.

The value is an integer that ranges from 0 to 15.

radio radio-id

Specifies the radio ID.

-

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

You can run this command to view the average signal strength of STAs connected to an AP.

Example

# Display the average signal strength of STAs connected to AP 0.

<Huawei> display ap id 0 sta-signal strength
  Station signal strength(%): 0      
Table 12-8  Description of the display ap id sta-signal strength command output
Item Description

Station signal strength(%)

Average signal strength of STAs.

display ap mem warn-threshold

Function

The display ap mem warn-threshold command displays the memory usage alarm threshold on an AP.

Format

display ap id ap-id mem warn-threshold

Parameters

Parameter

Description

Description

id ap-id

Specifies the AP ID.

The value is an integer that ranges from 0 to 15.

Views

All view

Default Level

1: Monitoring level

Usage Guidelines

None

Example

# Display the memory usage alarm threshold on AP 0.

<Huawei> display ap id 0 mem warn-threshold
Info: Memory threshold is 80%  
Related Topics

display ap-auth-mode

Function

The display ap-auth-mode command displays the AP authentication mode.

Format

display ap-auth-mode

Parameters

None

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

You can run the display ap-auth-mod command to the view the AP authentication mode.

Example

# Display the AP authentication mode.

<Huawei> display ap-auth-mode 
  AP authentication mode: no-auth 
Table 12-9  Description of the display ap-auth-mode command output
Item Description

AP authentication mode

Authentication mode used for APs.
  • mac-auth: APs are authenticated based on MAC addresses.
  • sn-auth: APs are authenticated based on SNs.
  • no-auth: No authentication is required.

display ap-elabel ap id

Function

The display ap-elabel ap id command displays electronic label information about a specified AP.

Format

display ap-elabel ap id ap-id

Parameters

Parameter

Description

Value

ap-id

Specifies the AP ID.

The value is an integer that ranges from 0 to 15.

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

You can run this command to view electronic label information about an AP. An electronic label is also called permanent configuration data or information and is written in the storage device during AP testing or commissioning. An electronic label includes the AP name, serial number, manufacture date and manufacturer information.

Example

# Display electrical label information about AP 0.

<Huawei> display ap-elabel ap id 0
/$[ArchivesInfo Version]                                                        
/$ArchivesInfoVersion=3.0                                                       
                                                                                
                                                                                
[Board Properties]                                                              
BoardType=AP6010DN-AGN                                                 
BarCode=020DND7410852010                                                        
Item=03020DND                                                                   
Description=                                                                    
Manufactured=2011-09-29                                                         
VendorName=Huawei                                                               
IssueNumber=00                                                                  
CLEICode=                                                                       
BOM=                 
Table 12-10  Description of the display ap-elabel ap id command output
Item Description
BoardType AP type.
BarCode Bar code of an AP.
Item BOM code of an AP.
Description English description of an AP.
Manufactured Production date of an AP.
VendorName Vendor name.
IssueNumber Issue number of an AP.
CLEICode CLEI code of an AP.
BOM Sales BOM code of an AP.

display ap-blacklist mac

Function

The display ap-blacklist mac command displays the AP blacklist.

Format

display ap-blacklist mac

Parameters

None

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

This command displays APs in the blacklist. These APs are not allowed to go online on the AC. If an AP is online on the AC but is in the blacklist, the AP is forced to log out.

Example

# Display the AP blacklist.

<Huawei> display ap-blacklist mac
  AP mac black list information:
  ------------------------------------------------------------------------------
  ID     MAC
  ------------------------------------------------------------------------------
  0      0001-0002-0001
  1      0001-0002-0002
  2      0001-0002-0003
  3      0001-0002-0004
  4      0001-0002-0005
  ------------------------------------------------------------------------------
  Total number: 5
Table 12-11  Description of the display ap-blacklist mac command output

Item

Description

AP mac black list information

MAC address list in the AP blacklist.

ID

ID of the MAC address in the AP blacklist. The ID is generated automatically when the MAC address is specified.

MAC

MAC addresses of the APs that are not allowed to connect to the AC.

To add MAC addresses to the AP blacklist, run the ap-blacklist mac command.

Related Topics

display ap lineate-port

Function

The display ap lineate-port command displays configurations on the AP wired interface.

Format

display ap id ap-id lineate-port interface-type interface-num

Parameters

Parameter

Description

Value

id ap-id

Specifies the AP ID.

-

interface-type interface-num

Specifies the AP wired interface. interface-type indicates the interface type, and interface-num indicates the interface number.

-

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

You can use this command to view configurations on the AP wired interface.

Example

# Display configurations on the GE interface of AP 1.

<Huawei> display ap id 1 lineate-port gigabitethernet 0
  AP 1 detail information:                                                      
  ------------------------------------------------------------------------------
  lineport number: 0                                                            
  lineport type: ge                                                             
  lineport description:                                                         
  lineport workmode : root                                                      
  lineport STP : disable                                                        
  lineport user-isolate : disable                                               
  lineport PVID VLAN : -                                                        
  lineport vlan tagged: -                                                       
  lineport vlan untagged: -                                                     
  lineport Eth-trunk: -                                                         
  lineport LLDP: enable                                                         
  lineport LLDP Basic TLV Management Address: enable                            
  lineport LLDP Basic TLV Port Description  : enable                            
  lineport LLDP Basic TLV System Capability : enable                            
  lineport LLDP Basic TLV System Description: enable                            
  lineport LLDP Basic TLV System Name       : enable                            
  lineport CRC warn switch: No                                                  
  lineport CRC warn high threshold: 50                                          
  lineport CRC warn low threshold: 20                                           
  lineport IPV4 Inbound ACL Number : -                                          
  lineport IPV4 Outbound ACL Number: -                                          
  lineport IPV6 Inbound ACL Number : -                                          
  lineport IPV6 Outbound ACL Number: -                                          
  ------------------------------------------------------------------------------
Table 12-12  Description about the display ap id ap-id lineate-port gigabitethernet interface-num command output

Item

Description

lineport number Number of the wired interface.
lineport type Type of the wired interface.
lineport description Description of the wired interface.
lineport workmode Mode of the wired interface.
lineport STP Whether to enable STP on the wired interface.
lineport user-isolate Whether to enable user isolation on the wired interface.
lineport PVID VLAN PVID of the wired interface.
lineport vlan tagged VLAN to which the interface is added in tagged mode.
lineport vlan untagged VLAN to which the interface is added in untagged mode.
lineport Eth-trunk Trunk ID to which the wired interface is bound.
lineport LLDP Whether to enable LLDP on the wired interface.
lineport LLDP Basic TLV Management Address Management IP address of the wired interface.
lineport LLDP Basic TLV Port Description Wired interface description.
lineport LLDP Basic TLV System Capability Wired interface capability set.
lineport LLDP Basic TLV System Description Wired interface system description.
lineport LLDP Basic TLV System Name Wired interface system name.
lineport CRC warn switch Whether to enable the alarm function for CRC errors on the wired interface.
lineport CRC warn high threshold Upper alarm threshold for CRC errors on the wired interface.
lineport CRC warn low threshold Lower alarm threshold for CRC errors on the wired interface.
lineport IPV4 Inbound ACL Number IPv4-based ACL in the inbound direction.
lineport IPV4 Outbound ACL Number IPv4-based ACL in the outbound direction.
lineport IPV6 Inbound ACL Number IPv6-based ACL in the inbound direction.
lineport IPV6 Outbound ACL Number IPv6-based ACL in the outbound direction.

# Display configurations on the Eth-trunk interface of AP 1.

<Huawei> display ap id 1 lineate-port eth-trunk 0
  AP 1 detail information:                                                      
  ------------------------------------------------------------------------------
  Eth-trunk ID: 0                                                               
  Eth-trunk description  : -                                                    
  Eth-trunk workmode : root                                                     
  Eth-trunk STP : disable                                                       
  Eth-trunk user-isolate : disable                                              
  Eth-trunk PVID VLAN : -                                                       
  Eth-trunk vlan tagged: -                                                      
  Eth-trunk vlan untagged: -                                                    
  lineport IPV4 Inbound ACL Number : -                                          
  lineport IPV4 Outbound ACL Number: -                                          
  lineport IPV6 Inbound ACL Number : -                                          
  lineport IPV6 Outbound ACL Number: -                                          
  ------------------------------------------------------------------------------
Table 12-13  Description about the display ap id ap-id lineate-port eth-trunk interface-num command output

Item

Description

Eth-trunk ID ID of the Eth-trunk interface.
Eth-trunk description Description of the Eth-trunk interface.
Eth-trunk workmode Eth-trunk interface mode.
Eth-trunk STP Whether to enable STP on the Eth-trunk interface.
Eth-trunk user-isolate Whether to enable user isolation on the Eth-trunk interface.
Eth-trunk PVID VLAN PVID of the Eth-trunk interface.
Eth-trunk vlan tagged VLAN to which the Eth-trunk interface is added in tagged mode.
Eth-trunk vlan untagged VLAN to which the Eth-trunk interface is added in untagged mode.
lineport IPV4 Inbound ACL Number IPv4-based ACL in the inbound direction.
lineport IPV4 Outbound ACL Number IPv4-based ACL in the outbound direction.
lineport IPV6 Inbound ACL Number IPv6-based ACL in the inbound direction.
lineport IPV6 Outbound ACL Number IPv6-based ACL in the outbound direction.

display ap online-fail-record

Function

The display ap online-fail-record command displays AP online failure records.

Format

display ap online-fail-record { all | mac mac-address }

Parameters

Parameter

Description

Value

all

Displays online failure records of all APs.

-

mac mac-address

Displays online failure records of the AP with the specified MAC address.

The value is in H-H-H format. An H is a hexadecimal number of 4 digits.

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

If an AP fails to go online on the AC, you can run the command to check the failure reason, which helps locate the fault.

After the number of AP online failure records reaches the maximum that can be stored, new records overwrites existing ones.

Example

# Display online failure records about the AP with the MAC address 04f9-3895-8300.

<Huawei> display ap online-fail-record mac 04f9-3895-8300
  ------------------------------------------------------------------------------
  MAC             Last fail time       Reason                                   
  ------------------------------------------------------------------------------
  04f9-3895-8300  2014-06-12/19:22:16  In blacklist        
  ------------------------------------------------------------------------------
  Total records: 1
Table 12-14  Description of the display ap online-fail-record command output

Item

Description

MAC

MAC address of the AP that fails to go online.

Last fail time

Time of the AP online failure.

Reason

Reason for the AP online failure.
  • AP IP address mismatch: The IP address used by the AP to report data differs from that configured on the AC.
  • AP auto update fail: The AP automatic upgrade fails.
  • Data batching: The AC is performing HA backup , and the AP is not allowed to go online.
  • In blacklist: The AP is in the blacklist.
  • Lack of license: The number of APs has reached the maximum supported by the license.
  • MAC and SN mismatched: The AP's MAC address and SN do not match.
  • Negotiation CAPWAP tunnel failed: The CAPWAP tunnel negotiation fails.
  • Negotiation DTLS failed: The DTLS negotiation fails.
  • Not in MAC whitelist: The MAC address of the AP is not in the MAC address whitelist.
  • Not in SN whitelist: The SN of the AP is not in the SN whitelist.

display ap offline-record

Function

The display ap offline-record command displays AP offline records.

Format

display ap offline-record { all | mac mac-address }

Parameters

Parameter

Description

Value

all

Displays offline records of all APs.

-

mac mac-address

Displays offline records of the AP with the specified MAC address.

The value is in H-H-H format. An H is a hexadecimal number of 4 digits.

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

This command displays AP offline records, helping the maintenance personnel manage and maintain the APs.

After the number of AP offline records reaches the maximum that can be stored, new records overwrites existing ones.

Example

# Display all AP offline records.

<Huawei> display ap offline-record all
  ------------------------------------------------------------------------------
  MAC               Last offline time      Reason                               
  ------------------------------------------------------------------------------
  60de-4476-e360    2014-06-16/14:10:04    Reboot by delete command         
                                                                                
  04f9-3895-8300    2014-06-12/19:45:17    Reboot by delete command         
                                                                                
  dcd2-fc04-b500    2014-06-12/17:26:39    Reboot by reset command           
                                                                                
  60de-4474-9640    2014-06-12/17:26:39    Reboot by reset command          
                                                                                
  ------------------------------------------------------------------------------
  Total records: 4
Table 12-15  Description of the display ap offline-record command output

Item

Description

MAC

AP's MAC address.

Last offline time

AP offline time.

Reason

AP offline reason.
  • Added to blacklist: The AP is in the blacklist.
  • Capwap link down: The CAPWAP link is disconnected.
  • Echo interval timeout: Echo packet transmission times out.
  • License expired: The license expires.
  • Link and AP state mismatched: The link state does not match the AP state.
  • Reboot by carrier or AC ID changed: The carrier ID or AC ID is changed.
  • Reoot by countrycode changed: The country code is changed.
  • Reboot by delete command: The AP is deleted using a delete command.
  • Reboot by DTLS switch changed: The status of DTLS encryption of the control channel is changed.
  • Reboot by MAC or SN modified: The MAC address or SN is changed.
  • Reboot by reset command: The AP is restarted using a restart command.
  • Reboot by static ip configured: The AP's IP address to be checked during CAPWAP tunnel establishment is configured using the corresponding command.
  • Reoot by update reset command: The AP is upgraded and restarted.

display ap-performance-statistic (for AC)

Function

The display ap-performance-statistic command displays performance statistics on an AP to monitor AP performance.

Format

display ap-performance-statistic id ap-id

Parameters

Parameter

Description

Value

id ap-id

Specifies the AP ID.

The value is an integer that ranges from 0 to 15.

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

The display ap-performance-statistic command displays the following information: performance statistics items, memory usage, CPU usage, available space in the flash memory, temperature, number of online users, upstream interface rate, total number of received frames, number of correct received frames, number of incorrect received frames, number of sent frames, number of received bytes, number of sent bytes, packet error rate of the upstream interface, traffic volume of the upstream interface in a specified period, and traffic volume of the wireless upstream interface in a specified period.

Example

# Display performance statistics on AP 0.

<Huawei> display ap-performance-statistic id 0   
  AP 0 performance statistic information:                                       
  ------------------------------------------------------------------------------
  Memory use rate: 62 %                                                         
  Memory average use rate: 62 %                                                 
  CPU use rate: 3 %                                                             
  CPU average use rate: 3 %                                                     
  Flash free size: 1192 KB                                                      
  Temperature: - °C                                                             
  Online user number: 1                                                         
  Up port traffic(wireless): 50 KB                                              
  Wireless port drop(send) frames: 2662                                         
  Wireless port drop(receive) frames: 0                                         
  Wireless port receive total Bytes : 52086                                     
  Wireless port send total Bytes: 6512                                          
  Wireless port receive unicast frames: 153                                     
  GigabitEthernet Port Number: 0                                                
    port drop(receive) frames: 0                                                
    port send total Bytes: 324813                                               
    port receive total Bytes: 326847                                            
    port drop send frames: 0                                                    
    port send error frames: 0                                                   
    port updown counts: 0                                                       
    port send unknown frames: 0                                                 
    port up rate(Kbps): 0                                                       
    port down rate(Kbps): 0                                  
  ------------------------------------------------------------------------------ 
Table 12-16  Description of the display ap-performance-statistic command output
Item Description
Memory use rate Memory usage (%).
Memory average use rate Average memory usage (%).
CPU use rate CPU usage (%).
CPU average use rate Average CPU usage (%).
Flash free size Available space in the flash memory, in KB.
Temperature Temperature (°C).
NOTE:

The temperature cannot be viewed on the AP2010DN, AP2030DN, AP4030DN, AP4130DN, AP3010DN-AGN, AP5010SN-GN, and AP5010DN-AGN. The value is displayed as "-".

Online user number Number of online users.
Up port traffic (wireless) Traffic volume on the wireless upstream interface in a specified period, in KB.
Wireless port drop(send) frames Number of discarded data frames that are sent by the wireless interface.
Wireless port drop(receive) frames Number of discarded data frames that are sent to the wireless interface.
Wireless port receive total Bytes Number of bytes received by the wireless interface.
Wireless port send total Bytes Number of bytes sent by the wireless interface.
Wireless port receive unicast frames Number of unicast data frames received by the wireless interface.
GigabitEthernet Port Number ID of the wired-side interface.
port drop(receive) frames Number of discarded frames on the wired-side interface.
port send total Bytes Number of bytes sent by the wired-side interface.
port receive total Bytes Number of bytes received by the wired interface.
port drop send frames Number of discarded data frames that are sent by the wired interface.
port send error frames Number of error data frames sent by the wired interface.
port updown counts Number of times the wired interface alternates between Up and Down.
port send unknown frames Number of unknown protocol packets received by the wired interface.
port up rate(Kbps) Upstream rate on the wired interface, in kbit/s.
port down rate(Kbps) Downstream rate on the wired interface, in kbit/s.

display ap-profile

Function

The display ap-profile command displays information about an AP profile.

Format

display ap-profile { all | default | id profile-id | name profile-name }

Parameters

Parameter

Description

Value

id profile-id

Specifies the ID of an AP profile.

The AP profile ID must exist.

name profile-name

Specifies the name of an AP profile.

The AP profile name must exist.

default

Displays information about the default AP profile.

-

all

Displays information about all AP profiles.

-

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

After an AP profile is configured, you can run this command to check detailed information about the AP profile.

Example

# Display information about the default AP profile.

<Huawei> display ap-profile default
  Default AP profile ID: 0                                                      
  Default AP profile name: ap-profile-0  
Table 12-17  Description of the display ap-profile default command output
Item Description
Default AP profile ID ID of the default AP profile.
Default AP profile name Name of the default AP profile.

# Display information about AP profile 0.

<Huawei> display ap-profile id 0 
  AP profile 0 detail information:                                              
  ------------------------------------------------------------------------------
  Name: ap-profile-0                                                            
  Ethernet port MTU: 1500 Bytes                                                 
  Log server ip address: 0.0.0.0                                                
  SampleTime(s): 30                                                             
  StatisticsTime(s): 60                                                         
  Eapol-start mode: multicast                                                   
  Eapol-start transform: specific                                               
  Eapol-response mode: unicast learning                                         
  Eapol-response transform: specific                                            
  Alarm restriction : enable                                                    
  Alarm restriction period(s) : 60                                              
  Telnet : enable                                                               
  Ssh : enable                                                                  
  Dhcp trust port : enable                                                      
  Temporary-management switch: disable                                          
  Max-sta-num: 128                                                              
  ------------------------------------------------------
Table 12-18  Description of the display ap-profile id command output
Item Description
Name Name of an AP profile.
Ethernet port MTU MTU of Ethernet interfaces.
Log server ip address IP address of the log server.
SampleTime(s) Sampling time.
StatisticsTime(s) Statistics time.
Eapol-start mode Eapol-start packet encapsulation mode.
Eapol-start transform Eapol-start packet transform mode.
Eapol-response mode Eapol-response packet encapsulation mode.
Eapol-response transform Eapol-response packet transform mode.
Alarm restriction Whether alarm suppression is enabled on an AP.
Alarm restriction period(s) Period of alarm suppression on an AP.

Telnet

Whether Telnet is enabled on an AP.

Ssh

Whether SSH is enabled on an AP.
Dhcp trust port Whether to enable the DHCP trusted port on an AP.

Temporary-management switch

Status of management VAP and antenna alignment VAP for offline APs.
Max-sta-num Maximum number of access users on the AP.

# Display information about all AP profiles.

<Huawei> display ap-profile all  
 All AP profiles information:                                                  
  ----------------------------------------------------------------------------  
  ID     Name                                                                   
  ----------------------------------------------------------------------------  
  0      ap-profile-0                                                           
  1      ap2                                                                     
  ----------------------------------------------------------------------------  
  Total number: 2 
Table 12-19  Description of the display ap-profile all command output
Item Description
ID ID of an AP profile.
Name Name of an AP profile.
Total number Total number of AP profiles.

display ap-region

Function

The display ap-region command displays the configuration of an AP region.

Format

display ap-region { default | all | id region-id }

Parameters

Parameter

Description

Value

default

Displays the configuration of the default AP region.

-

all

Displays configurations of AP regions.

-

id region-id

Displays the configuration of a specified AP region.

The value is an integer that ranges from 0 to 15.

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

  • If default is specified, the ID of the default AP region is displayed.
  • If an AP region is specified, the ID and name of the AP region, AP deployment mode in the region, and number of APs in the region are displayed.
  • If all is specified, the ID and name of reach AP region, number of APs in each AP region, and number of AP regions are displayed.

Example

# Display information about the default AP region.

<Huawei> display ap-region default
  Default AP region ID: 0  

# Display information about AP region 10.

<Huawei> display ap-region id 10
  AP region 10 detail information:                                              
  ----------------------------------------------------------------------------  
  Name: ap-region-10                                                            
  Deploy-mode: normal-deploy                                                    
  Total AP number: 0                                                            
  ----------------------------------------------------------------------------  

# Display information about all AP regions.

<Huawei> display ap-region all 
  All AP regions information:                                                   
  ----------------------------------------------------------------------------  
  ID     Name                              Total AP number                      
  ----------------------------------------------------------------------------  
  0      ap-region-0                       2                                    
  10     ap-region-10                      0                                    
  ----------------------------------------------------------------------------  
  Total number: 2   
Table 12-20  Description of the display ap-region command output

Item

Description

Default AP region ID

ID of the default AP region.

Name

Name of an AP region.

Deploy-mode

AP deployment mode in an AP region.

Total AP number

Number of APs in an AP region.

display ap-run-info (for AC)

Function

The display ap-run-info command displays the running status of an AP. You can run this command to monitor an AP in real time.

Format

display ap-run-info id ap-id

Parameters

Parameter

Description

Value

id ap-id

Specifies the AP ID.

The value is an integer that ranges from 0 to 15.

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

Usage Scenario

This command displays AP running status.

Prerequisites

The AP works properly.

Example

# Display the running status of AP 0.

<Huawei> display ap-run-info id 0  
  AP 0 run information:                                                         
  ------------------------------------------------------------------------------
  Software version: V200R005C10                                           
  Hardware version: Ver.C                                                       
  BIOS version: 219                                                             
  Country code: CN                                                              
  CPU type: AR9344                                                              
  CPU frequency: 480 MHZ                                                        
  Memory type: H5PS5162GFR-S6C&1                                                
  AP system software description: AP6310SN-GN:V200R005C10SPC200                 
  AP system hardware description: AP6310SN-GN:Ver.C                             
  AP manufacture: Huawei Technologies Co., Ltd.                                 
  AP software name: Huawei Access Point Software                                
  AP software vendor: Huawei Technologies Co., Ltd.                             
  AP online time: 42 S                                                          
  AP bom code: 000                                                              
  Ip address: 192.168.101.254                                                   
  Ip mask: 255.255.255.0                                                        
  Gateway ip: 192.168.101.1                                                     
  DNS server: 0.0.0.0                                                           
  Memory size: 128 MB                                                           
  Flash size: 32 MB                                                             
  Run time: 154 S                                                               
  GigabitEthernet port number : 0                                               
    Port speed: 100 Mbps                                                        
    Port speed mode: auto                                                       
    Port duplex: full                                                           
    Port duplex mode: auto                                                      
    Port state: up                                                              
  ------------------------------------------------------------------------------
Table 12-21  Description of the display ap-run-info command output

Item

Description

Software version

Software version of an AP.

Hardware version

Hardware version of an AP.

BIOS version

BIOS version of an AP.

Country code

Country code.

CPU type

CPU type of an AP.

CPU frequency

CPU frequency of an AP.

Memory type

Memory type of an AP.

AP system software description

System software description of an AP.

AP System hardware description

System hardware description of an AP.

AP manufacture

Manufacturer of an AP.

AP software name

Software name of an AP.

AP software vendor

AP software manufacturer.

AP online time

AP online duration, in seconds.

AP bom code

BOM code of an AP.

Ip address

IP address of an AP.

Ip mask

Mask of an AP.

Gateway ip

Gateway IP address of an AP.

DNS server

IP address of the DNS server.

Memory size

Memory size of an AP, in MB.

Flash size

Flash memory size of an AP, in MB.

Run time

Running duration of an AP, in seconds.

GigabitEthernet port number

ID of the AP's Ethernet interface.

Port speed

Rate on the upstream Ethernet interface, in Mbit/s.

Port speed mode

Rate mode of the upstream Ethernet interface, including automatic and non-automatic negotiation modes.

Port duplex

Duplex type of the upstream Ethernet interface, including full duplex and half duplex.

Port duplex mode

Duplex mode of the upstream Ethernet interface, including automatic and non-automatic negotiation modes.

Port state

AP interface status.

  • down: indicates that the interface is disabled.
  • up: indicates that the interface is enabled.

display ap-type

Function

The display ap-type command displays AP type information.

Format

display ap-type { all | id type-id | type ap-type }

Parameters

Parameter

Description

Value

all

Displays all supported AP types.

-

id type-id

Specifies the AP type ID.

The value is an integer that ranges from 0 to 255.

type ap-type

Specifies the AP type.

The value is a string of 1 to 31 characters. The value cannot contain question marks (?) or spaces and cannot start or end with double quotation marks (" "). The value must start with Ap, aP or ap.

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

  • If an AP type is specified, the AP type ID, AP type, AP type description, number of radios, radio type, maximum number of users, number of VAPs, and antenna gain are displayed.
  • If all is specified, all AP type IDs, AP types, and number of AP types are displayed.

Example

# Display information about AP type 17.

<Huawei> display ap-type id 17 
  AP type 17 detail information:                                                
  ------------------------------------------------------------------------------
  Type: AP6010SN-GN                                                             
  Description: ap-type-17                                                       
  Lineate port number: 1                                                        
  Lineate port 0 type: GE
  Radio number: 1                                                               
  Radio 0 type: 802.11bgn                                                       
  Radio 0 maximal spatial streams: 2                                            
  Radio 0 maximal antenna number: 2                                             
  Radio 0 maximal VAP number: 16                                                
  Radio 0 antenna gain: 4                                                       
  Maximum station number: 128                                                   
  ------------------------------------------------------------------------------
Table 12-22  Description of the display ap-type id command output

Item

Description

Type

AP type.

Description

Description of the AP type.

Lineate port number

Number of wired interfaces.

Lineate port 0 type

Type of wired interfaces.

Radio number

Number of radios.

Radio 0 type

Type of the radio. The value 0 indicates the radio ID.

Radio 0 maximal spatial streams

Maximum number of spatial streams on the radio.

Radio 0 maximal antenna number

Maximum number of antennas on the radio.

Radio 0 maximal VAP number

Maximum number of VAPs of the radio.

Radio 0 antenna gain

Antenna gain of the radio, in dB.

Maximum station number

Maximum number of STAs supported by the AP type.

# Display all AP types.

<Huawei> display ap-type all 
  All AP types information:                                                     
  ------------------------------------------------------------------------------
  ID     Type                                                                   
  ------------------------------------------------------------------------------
  17     AP6010SN-GN                                                            
  19     AP6010DN-AGN                                                           
  21     AP6310SN-GN                                                            
  23     AP6510DN-AGN                                                           
  25     AP6610DN-AGN                                                           
  27     AP7110SN-GN                                                            
  28     AP7110DN-AGN                                                           
  29     AP5010SN-GN                                                            
  30     AP5010DN-AGN                                                           
  31     AP3010DN-AGN                                                           
  33     AP6510DN-AGN-US                                                        
  34     AP6610DN-AGN-US                                                        
  35     AP5030DN                                                               
  36     AP5130DN                                                               
  37     AP7030DE                                                               
  38     AP2010DN                                                               
  39     AP8130DN                                                               
  40     AP8030DN                                                               
  43     AP4030DN                                                               
  44     AP4130DN                                                               
  45     AP3030DN                                                               
  46     AP2030DN                                                               
  ------------------------------------------------------------------------------
  Total number: 22                   
Table 12-23  Description of the display ap-type all command output

Item

Description

ID

ID of an AP.

Type

Type of an AP.

display ap-common-info

Function

The display ap-common-info command displays common information about APs.

Format

display ap-common-info { all | ap-id ap-id | ap-mac ap-mac }

Parameters

Parameter

Description

Value

all

Displays common information about all APs.

-

ap-id ap-id

Specifies an AP ID.

The value is an integer that ranges from 0 to 15.

ap-mac ap-mac

Specifies the MAC address of an AP.

The value is in H-H-H format. An H is a hexadecimal number of four digits.

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

This command is applicable to the following scenarios:
  • If an AP has been associated with an AC, you can run this command to view common information about the AP, including the AP ID, MAC address, software version, status, and IP address.
  • If an AP has been disconnected from an AC, you can run this command to view only the AP ID, MAC address, and status.
NOTE:

If an AP has not been connected to an AC, for example, an AP is added offline, no information about the AP software version or IP address is displayed when you run this command.

Example

# Display common information about all APs.

<Huawei> display ap-common-info all
  ------------------------------------------------------------------------------
  AP-ID    AP-MAC        Software-version    AP-state            IP-address     
  1     1047-80b1-56a0   V200R003C00         normal              192.168.40.253 
                                                                                
  Radio-ID        Ess-ID          STA-number                                    
  0               0               0
 ------------------------------------------------------------------------------
  Total number: 1

# Display common information about AP 1.

<Huawei> display ap-common-info ap-id 1
  ------------------------------------------------------------------------------
  AP-ID    AP-MAC        Software-version    AP-state            IP-address     
  5     1047-80b1-56a0   V200R003C00         normal              192.168.40.253 
  ------------------------------------------------------------------------------
Table 12-24  Description of the display ap-common-info command output

Item

Description

AP-ID

ID of the AP.

AP-MAC

MAC address of the AP.

Software-version

Software version of the AP.

AP-state

Running status of the AP.

IP-address

IP address of the AP.

Radio-ID

Radio ID.

Ess-ID

ESS ID

STA-number

Number of connected STAs.

display ap-update ftp-server

Function

The display ap-update ftp-server command displays the FTP configuration for AP upgrade.

Format

display ap-update ftp-server

Parameters

None

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

You can run this command to check FTP server configurations during AP version upgrade.

Example

# Display the FTP configuration used for AP upgrade.

<Huawei> display ap-update ftp-server
  FTP IP               : -
  FTP username         : anonymous                                              
  FTP password         : ******                                                 
Table 12-25  Description of the display ap-update ftp-server command output

Item

Description

FTP IP

IP address of the FTP server.

FTP username

User name for logging in to the FTP server.

FTP password

Password for logging in to the FTP server.

display ap-update update-filename

Function

The display ap-update update-filename command displays the name of the upgrade version file for a specified AP type.

Format

display ap-update update-filename ap-type type-id

Parameters

Parameter

Description

Value

ap-type type-id

Specifies the AP type ID.

The value is an integer that ranges from 0 to 255.

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

You can run this command to view the name of the upgrade version file for a specified AP type.

Example

# Display the name of the upgrade version file for a specified AP type.

<Huawei> display ap-update update-filename ap-type 19
  AP update filename : FitAP6X10XN_V200R003C00.bin   

Table 12-26  Description of the display ap-update update-filename command output

Item

Description

AP update filename

Name of the upgrade version file for a specified AP type.

display bssid-decode

Function

The display bssid-decode command displays VAP information.

Format

display bssid-decode bssid

Parameters

Parameter

Description

Value

bssid

Specifies the BSSID of the VAP. You can run the display vap command to check VAP BSSIDs.

The value is in H-H-H format. An H is a hexadecimal number of 4 digits.

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

This command displays information about the VAP with the specified BSSID. You can compare the carrier ID and AC ID in the command output with those on the AC. If they are consistent, the VAP belongs to the current AC.

Example

# Display information about the VAP with BSSID 60DE-4474-9640.

<Huawei> display bssid-decode 60DE-4474-9640
  ----------------------------------------------------------------------------- 
  Carrier ID  AC ID  AP ID  Radio ID  WLAN ID                                   
  other       1      1      0         1                                         
  ----------------------------------------------------------------------------- 
  Current carrier ID:other                                                      
  Current AC ID     :1  
Table 12-27  Description of the display bssid-decode command output

Item

Description

Carrier ID

Carrier ID of the VAP.

AC ID

AC ID of the VAP.

AP ID

AP ID of the VAP.

Radio ID

Radio ID bound to the VAP.

WLAN ID

Identifier of the VAP on the radio.

Current carrier ID

Carrier ID of the current device.

Current AC ID

AC ID of the current device.
Related Topics

display ap-whitelist

Function

The display ap-whitelist command displays information about the AP whitelist.

Format

display ap-whitelist { mac | sn }

Parameters

Parameter

Description

Value

sn

Displays serial numbers (SNs) in the AP whitelist.

-

mac

Displays MAC addresses in the AP whitelist.

-

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

When the AP authentication mode is set to MAC authentication or SN authentication using the ap-auth-mode command, you can run the ap-whitelist mac or ap-whitelist sn command to configure an AP whitelist. Only APs on the whitelist are allowed to go online. To check information about APs in the whitelist, run the display ap-whitelist command.

Example

# Display MAC addresses in the AP whitelist.

<Huawei> display ap-whitelist mac
 AP mac white list information:
  ----------------------------------------------------------------------------
  ID     MAC
  ----------------------------------------------------------------------------
  0      0025-9e07-7fe0
  1      0025-9e27-3290
  ----------------------------------------------------------------------------
  Total number: 2
Table 12-28  Description of the display ap-whitelist mac command output

Item

Description

ID

ID of an AP.

MAC

MAC address of an AP.

To add a MAC address to the AP whitelist, run the ap-whitelist mac command.

# Display SNs in the AP whitelist.

<Huawei> display ap-whitelist sn
  AP SN white list information:                                                 
  ------------------------------------------------------------------------------
  ID     SN                                                                     
  ------------------------------------------------------------------------------
  0      210235419610CB000473                                            
  1      210235419610CB000564                                                   
  ------------------------------------------------------------------------------
  Total number: 2
Table 12-29  Description of the display ap-whitelist sn command output

Item

Description

ID

ID of an AP.

SN

SN of an AP.

To add an SN to the AP whitelist, run the ap-whitelist sn command.

display binding radio-profile (for AC)

Function

The display binding radio-profile command displays radios to which a specified radio profile is bound.

Format

display binding radio-profile { id profile-id | name profile-name }

Parameters

Parameter

Description

Value

id profile-id

Specifies the radio profile ID.

The radio profile ID must exist.

name profile-name

Specifies the name of a radio profile.

The radio profile name must exist.

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

Usage Scenario

You can run this command to view the radios to which a specified radio profile is bound.

Prerequisites

When using this command, ensure that the specified radio profile exists.

Example

# Display the radios to which radio profile 0 is bound.

<Huawei> display binding radio-profile id 0
  ----------------------------------------------------                          
   AP  RADIO                                                                    
  ----------------------------------------------------                          
   1    0                                                                       
   0    0                                                                       
  ----------------------------------------------------                          
   Total: 2  
Table 12-30  Description of the display binding radio-profile command output

Item

Description

AP

ID of an AP.

RADIO

Radio ID.

display capwap configuration

Function

The display capwap configuration command displays the CAPWAP configuration.

Format

display capwap configuration

Parameters

None

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

You can run this command to view the interval for sending Keepalive packets, number of times for sending Keepalive packets, and priority of CAPWAP management packets.

Example

# Display the CAPWAP configuration.

<Huawei> display capwap configuration
CAPWAP config:                                     
  ------------------------------------------------------------                  
  Capwap source interface             : vlanif100                               
  Capwap source ip-address            : -                                       
  Keep-alive interval(seconds)        : 25                                      
  Keep-alive times                    : 6                                       
  Capwap control priority(AC to AP)   : 7                                       
  Capwap control priority(AP to AC)   : 7                                       
  Control-link dtls switch state      : disable                                 
  Dtls psk value                      : ******                                  
  Dtls default key switch             : enable                                  
  ------------------------------------------------------------   
Table 12-31  Description of the display capwap configuration command output

Item

Description

Capwap source interface

AC's source interface.

To configure the parameter, run the capwap source interface command.

Capwap source ip-address

AC's source address.

To configure the parameter, run the capwap source ip-address command.

Keep-alive interval(seconds)

CAPWAP heartbeat detection interval, that is, the interval at which two detection packets are sent.

To configure the parameter, run the capwap keep-alive interval command.

Keep-alive times

Number of CAPWAP heartbeat detections. If no response is received after the specified number of times, the link is considered disconnected.

To configure the parameter, run the capwap keep-alive times command.

Capwap control priority(AC to AP)

Priority of CAPWAP management packets from an AC to an AP.

To configure the priority of CAPWAP management packets from an AC to an AP, run the capwap control-link-priority local priority-value command.

Capwap control priority(AP to AC)

Priority of CAPWAP management packets from an AP to an AC.

To configure the priority of CAPWAP management packets from an AP to an AC, run the capwap control-link-priority remote priority-value command.

Dtls psk value

Pre-shared key for DTLS encryption.

To configure the pre-shared key for DTLS encryption, run the capwap dtls psk command.

Control-link dtls switch state

Whether CAPWAP control tunnel using DTLS is enabled.

Dtls default key switch

Whether an AP is enabled to perform DTLS sessions with the AC using the default pre-shared key.

display channel country-code(for AC)

Function

The display channel country-code command displays 2.4 GHz and 5 GHz channels corresponding to a specified country code.

Format

display channel country-code country-code

Parameters

Parameter

Description

Value

country-code

Specifies the AC country code.

The value is a string of characters. For specific values, see Table 12-32.

Table 12-32  Country codes supported by ACs

Country Code

Country/Region

AE

UNITED ARAB EMIRATES

AM

ARMENIA

AR

ARGENTINA

AT

AUSTRIA

AU

AUSTRALIA

AZ

AZERBAIJAN

BE

BELGIUM

BG

BULGARIA

BH

BAHRAIN

BN

BRUNEI DARUSSALAM

BO

BOLIVIA

BR

BRAZIL

BY

BELARUS

BZ

BELIZE

CA

CANADA

CH

SWITZERLAND

CL

CHILE

CN

CHINA (Default)

CO

COLOMBIA

CR

COSTA RICA

CY

CYPRUS

CZ

CZECH REPUBLIC

DE

GERMANY

DK

DENMARK

DO

DOMINICAN REPUBLIC

EC

ECUADOR

EE

ESTONIA

EG

EGYPT

ES

SPAIN

FI

FINLAND

FR

FRANCE

GB

UNITED KINGDOM

GE

GEORGIA

GR

GREECE

GT

GUATEMALA

HK

HONG KONG,SPECIAL ADMINISTRATIVE REGION OF CHINA

HN

HONDURAS

HR

CROATIA

HU

HUNGARY

ID

INDONESIA

IE

IRELAND

IL

ISRAEL

IN

INDIA

IQ

IRAQ

IR

IRAN

IS

ICELAND

IT

ITALY

JO

JORDAN

JP

JAPAN

KP

DEMOCRATIC PEOPLE'S REPUBLIC OF KOREA

KR

REPUBLIC OF KOREA

KW

KUWAIT

KZ

KAZAKHSTAN

LB

LEBANON

LI

LIECHTENSTEIN

LK

SRI LANKA

LT

LITHUANIA

LU

LUXEMBOURG

LV

LATVIA

MA

MOROCCO

MC

MONACO

MK

MACEDONIA

MO

MACAU,SPECIAL ADMINISTRATIVE REGION OF CHINA

MT

MALTA

MX

MEXICO

MY

MALAYSIA

NG

NIGERIA

NL

NETHERLANDS

NO

NORWAY

NZ

NEW ZEALAND

OM

OMAN

PA

PANAMA

PE

PERU

PH

PHILIPPINES

PK

PAKISTAN

PL

POLAND

PR

PUERTO RICO

PT

PORTUGAL

QA

QATAR

RO

ROMANIA

RU

RUSSIA

SA

SAUDI ARABIA

SE

SWEDEN

SG

SINGAPORE

SI

SLOVENIA

SK

SLOVAKIA

SV

EL SALVADOR

SY

SYRIA

TH

THAILAND

TN

TUNISIA

TR

TURKEY

TT

TRINIDAD & TOBAGO

TW

TAIWAN,PROVINCE OF CHINA

UA

UKRAINE

US

UNITED STATES

UY

URUGUAY

UZ

UZBEKISTAN

VE

VENEZUELA

VN

VIET NAM

YE

YEMEN

ZA

SOUTH AFRICA

ZW

ZIMBABWE

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

You can run the display channel country-code command to view 2.4 GHz and 5 GHz channels corresponding to a specified country code.

Example

# Display 2.4 GHz and 5 GHz channels corresponding to the country code CN.

<Huawei> display channel country-code CN
  2.4G 20M : 1,2,3,4,5,6,7,8,9,10,11,12,13.                                     
  2.4G 40M+: 1,2,3,4,5,6,7.                                                     
  2.4G 40M-: 5,6,7,8,9,10,11.                                                   
  5G   20M : 36,40,44,48,52,56,60,64,149,153,157,161,165.                       
  5G   40M+: 36,44,52,60,149,157.                                               
  5G   40M-: 40,48,56,64,153,161.                                               
  5G   80M : 36,40,44,48,52,56,60,64,149,153,157,161. 
Table 12-33  Description of the display channel country-code command output

Parameter

Description

2.4G 20M : 1,2,3,4,5,6,7,8,9,10,11,12,13

NOTE:

Description is only provided for the first line of the command output. The description about the rest lines is similar.

2.4G indicates the frequency band of a radio; 20M indicates the channel bandwidth; 1,2,3,4,5,6,7,8,9,10,11,12,13 are IDs of channels at the 2.4 GHz frequency band.

See Country Code & Channel Compliance Table for the relationship between the channel IDs and frequency band.

display interface wlan-ess

Function

The display interface wlan-ess command displays the running status of and statistics on a WLAN-ESS interface.

Format

display interface wlan-ess [ wlan-ess-number ]

Parameters

Parameter

Description

Value

wlan-ess-number

Specifies the number of a WLAN-ESS interface.

The value is an integer that ranges from 0 to 15.

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

Usage Scenario

To monitor the interface status or locate faults on an interface, run this command to obtain status of the interface. You can collect traffic statistics and locate faults on the interface according to the command output.

Prerequisites

When using this command, ensure that the wlan-ess interface exists.

Example

# Display the status of and statistics on the wlan-ess 1 interface.

<Huawei> display interface wlan-ess 1
Wlan-Ess1 current state : UP
Line protocol current state : UP
Description:HUAWEI, AR Series, Wlan-Ess1 Interface
Switch Port, TPID : 8100(Hex), The Maximum Transmit Unit is 1500
IP Sending Frames' Format is PKTFMT_ETHNT_2, Hardware address is 5489-98f3-628d
Current system time: 2013-04-12 15:53:21
-----------------------------------------------------
PortName                Status
-----------------------------------------------------
Wlan-Dbss1:0            UP
Table 12-34  Description of the display interface wlan-ess command output

Item

Description

Wlan-Ess1 current state Status of the Wlan-Ess1 interface.
Line protocol current state Current status of the link-layer protocol.
Description Interface description.
Switch Port Layer 2 interface.
TPID Default VLAN.
IP Sending Frames' Format Format of the frame contained in a sent IP packet.
Current system time Current system time.
PortName WLAN-DBSS interface name.
Status WLAN-DBSS interface status.
Related Topics

display lldp ap-neighbor

Function

The display lldp ap-neighbor command displays LLDP neighbor information on a specified AP.

Format

display lldp ap-neighbor [ ap-id [ port port-number ] ]

Parameters

Parameter

Description

Value

ap-id

Specifies an AP ID.

The value is an integer that ranges from 0 to 15.

port-number

Specifies an interface number.

The value is an integer that ranges from 0 to 7.

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

You can run this command to view LLDP neighbor information on a specified AP, including the number of LLDP neighbors, device ID, interface ID, system name system description, and management address of each neighbor. The LLDP neighbor information is reported by an AP to the connected AC.

Example

# Display LLDP neighbor information on port 0 of AP 0.

<Huawei> display lldp ap-neighbor 0 port 0
  ------------------------------------------------------------------------------                                                    
  AP 0 Port 0 has 1 neighbor(s):                                                                                                    
                                                                                                                                    
  Neighbor index: 1                                                                                                                 
  Chassis ID type: macAddress                                                                                                       
  Chassis ID: 00e0-fc03-0201                                                                                                        
  Port ID type: interfaceName                                                                                                       
  Port ID: Ethernet2/0/0                                                                                                            
  Time To Live: 120s                                                                                                                
  Port Description: HUAWEI, AR Series, Ethernet2/0/0 Interface                             
  System name: Huawei                                                                                                               
  System description: Huawei  
   Huawei Versatile Routing Platform Software  
   VRP (R) software,Version 5.120 ( V200R003C00) 
   Copyright (C) 2000-2011 Huawei Technologies Co., Ltd                                                                          
  System capabilities supported: bridge                                                                                             
  System capabilities enabled: bridge                                                                                               
  Management address type: ipV4                                                                                                     
  Management address: 10.2.2.2                                                                                                       
  ------------------------------------------------------------------------------  
Table 12-35  Description of the display lldp ap-neighbor command output

Item

Description

Neighbor index

Index of a neighbor.

Chassis ID type

ID subtype of a neighbor device.
  • chassisComponent: chassis alias
  • interfaceAlias: interface alias
  • portComponent: interface or backplane alias
  • macAddress: MAC address
  • networkAddress: network address
  • interfaceName: name of the interface
  • local: name of the local device

Chassis ID

ID of the neighbor device.
  • A MAC address is displayed when the neighbor device ID subtype is macAddress.
  • An IP address is displayed when the neighbor device ID subtype is networkAddress.
  • A character string is displayed when the neighbor device ID subtype is neither macAddress nor networkAddress.

Port ID type

ID subtype of the neighbor interface.
  • interfaceAlias: interface alias
  • portComponent: interface or backplane alias
  • macAddress: MAC address
  • networkAddress: network address
  • interfaceName: name of the interface
  • agentCircuitID: loopback interface ID of the DHCP relay
  • local: name of the local device

Port ID

ID of the neighbor interface.
  • A MAC address is displayed when the neighbor interface ID subtype is macAddress.
  • An IP address is displayed when the neighbor interface ID subtype is networkAddress.
  • A character string is displayed when the neighbor interface ID subtype is neither macAddress nor networkAddress.

Time To Live

Time to live (TTL) of the local device information stored on the neighbor device.

Port Description

Description of the neighbor interface.

System name

System name.

System description

System description of the neighbor.

System capabilities supported

Capabilities of the neighbor device.
  • other: other capabilities
  • repeater: repeater
  • bridge: bridge device
  • wlanAccessPoint: wireless access point
  • router: router
  • telephone: wireless device
  • docsisCableDevice: management station
  • stationOnly: base station

System capabilities enabled

Capabilities enabled on the neighbor device.
  • other: other capabilities
  • repeater: repeater
  • bridge: bridge device
  • wlanAccessPoint: wireless access point
  • router: router
  • telephone: wireless device
  • docsisCableDevice: management station
  • stationOnly: base station

Management address type

Management address type of the neighbor.

Management address

Management address of the neighbor.

Related Topics

display optical-info

Function

The display optical-info command displays optical module information on a specified AP.

Format

display optical-info ap-id ap-id

Parameters

Parameter

Description

Value

ap-id ap-id

Displays optical module information on a specified AP.

The value is an integer that ranges from 0 to 15.

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

Usage Scenario

You can run this command to view optical module information on a specified AP, including the optical module type, transmit optical power, and receive optical power.

Prerequisites

The AP has been online. You can run the display ap command to check the AP status.

The AP supports optical modules. You can run the display ap-type command to view the AP model.
NOTE:

Currently, only the AP6610DN-AGN and AP6610DN-AGN-US support optical modules.

Example

# Display optical module information on AP 1.

<Huawei> display optical-info ap-id 1
----------------------------------------------------------------
 Nominal bit rate                    :1200 MBit/s
 Length(9um)-km                      : 10 km
 Length(50um)                        : 550 m
 Length(62.5um)                      : 550 m
 Length(Copper)                      : 0 m
 Connector                           : LC
 Supply voltage(V)                   : 3
 TX bias current(mA)                 : -
 TX power(dBm)                       : -
 RX power(dBm)                       : -
 Temperature(C)                      : 50
 Vendor OUI                          : 5994
 Vendor name                         : HW
 Vendor PN                           : HFCT-5710L
 Vendor rev                          : ABC
 Vendor sn                           : AB07263947
----------------------------------------------------------------
Table 12-36  Description of the display optical-info command output

Item

Description

Nominal bit rate Bit rate of the optical module, in Mbit/s.
Length(9um)-km Transmission distance of the standard single-mode optical fiber, in kilometers.
Length(50um) Length of the multi-mode optical fiber (with diameter 50 or 125 um), in meters.
Length(62.5um) Length of the multi-mode optical fiber (with diameter 62.5 or 125 um), in meters.
Length(Copper) Length of the copper cable, in meters.
Connector Connector of the optical module.
Supply voltage(V) Voltage of the optical module, in volts.
TX bias current(mA) Bias current of the optical module, in mA.
TX power(dBm) Transmit optical power, in dBm.
RX power(dBm) Receive optical power, in dBm.
Temperature(C) Temperature of the optical module, in °C.
Vendor OUI Unique identifier of a vendor, which is allocated by the IEEE.
Vendor name Name of the vendor.
Vendor PN Product code provided by the vendor.
Vendor rev Version number provided by the vendor.
Vendor sn Product serial number provided by the vendor.

display power-level (for AC)

Function

The display power-level command displays the radio power level and corresponding power.

Format

display power-level ap-id ap-id radio-id radio-id

Parameters

Parameter

Description

Value

ap-id ap-id

Specifies an AP ID. The AP ID and radio ID identify a radio. To specify the AP ID, run the command.

The value is an integer that ranges from 0 to 15.

radio-id radio-id

Specifies the radio ID. The radio ID and AP ID identify a radio.

The value is an integer that ranges from 0 to 3.

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

The display power-level command displays the radio power level and corresponding power. The radio power level and corresponding power vary according to AP radios.

The power in the command output is the sum of the maximum transmit power of the radio interface and the antenna gain. If MIMO is supported, the MIMO gain should also be added. The maximum power displayed should comply with laws and regulations corresponding to the country code.

Example

# Display the power level and corresponding power of radio0/0.

<Huawei> display power-level ap-id 0 radio-id 0 
 power-level num: 20                                                            
 level 0: 20.00 dBm                                                             
 level 1: 19.00 dBm                                                             
 level 2: 18.00 dBm                                                             
 level 3: 17.00 dBm                                                             
 level 4: 16.00 dBm                                                             
 level 5: 15.00 dBm                                                             
 level 6: 14.00 dBm                                                             
 level 7: 13.00 dBm                                                             
 level 8: 12.00 dBm                                                             
 level 9: 11.00 dBm                                                             
 level 10: 10.00 dBm                                                            
 level 11: 9.00 dBm                                                             
 level 12: 8.00 dBm                                                             
 level 13: 7.00 dBm                                                             
 level 14: 6.00 dBm                                                             
 level 15: 5.00 dBm                                                             
 level 16: 5.00 dBm                                                             
 level 17: 5.00 dBm                                                             
 level 18: 5.00 dBm                                                             
 level 19: 5.00 dBm           
NOTE:

The displayed information is for reference only and varies according to the actual device.

Table 12-37  Description of the display power-level command output

Item

Description

power-level num

Radio power level.

level 0: 20.00 dBm

Power corresponding to power level 0.

display radio config

Function

The display radio config command displays current configurations of an AP radio.

Format

display radio config ap-id ap-id radio-id radio-id

Parameters

Parameter

Description

Value

ap-id ap-id

Specifies an AP ID.

The value is an integer that ranges from 0 to 15.

radio-id radio-id

Specifies the radio ID.

The value is an integer that ranges from 0 to 3.

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

You can run this command to view the radio profile bound to a radio, and the radio parameters, administrative status, channel, and power specified in the radio profile.

Example

# Display the configuration of radio 0/0.

<Huawei> display radio config ap-id 0 radio-id 0 
  -----------------------------------------------------------------------       
  Administrate status                    :enable                                
  Channel                                :1                                     
  Channel bandwidth                      :20MHz                                 
  Power level                            :0                                     
  Power(dBm)                             :30                                    
  Available antenna number               :all                                   
  Join load-balance-group                :-                                     
  Attack Detect                          :-                                     
  Bridge switch                          :disable                               
  Bridge mode                            :-                                     
  Bridge whitelist switch                :disable                               
  Bind bridge whitelist ID               :-                                     
  Bind bridge whitelist name             :-                                     
  Bridge stp switch                      :disable                               
  Antenna gain(dbi)                      :3                                     
  Profile ID                             :0                                     
  Profile name                           :radio                                 
  Channel mode                           :auto                                  
  Power mode                             :auto                                  
  Calibrate interval(min)                :5                                     
  PER threshold(%)                       :30                                    
  Conflict rate threshold(%)             :60                                    
  RTS/CTS threshold(Byte)                :2347                                  
  Fragmentation threshold(Byte)          :2346                                  
  Short retry number limit               :7                                     
  Long retry number limit                :4                                     
  Support short preamble                 :support                               
  DTIM interval (Beacon interval numbers):1                                     
  Beacon interval(ms)                    :100                                   
  WMM profile ID                         :0                                     
  WMM profile name                       :wmm                                   
  Interference detect switch             :disable                               
  Calibrate switch                       :enable                                
  Calibrate scan-cycle(s)                :60                                    
  RTS/CTS mode                           :CTS-TO-SELF                           
  Wifi-light mode                        :signal-strength                       
  802.11n guard interval mode            :normal                                
  802.11n A-MPDU length limit            :3                                     
  Channel scan-frequency(ms)             :10000                                 
  Channel scan-time(ms)                  :60                                    
  802.11ac guard interval mode           :normal                                
  802.11ac A-MPDU length limit           :7                                     
  Legacy station access                  :enable                                
  80211bg basic rate                     :1 2                                   
  80211bg support rate                   :1 2 5 6 9 11 12 18 24 36 48 54        
  80211a basic rate                      :6 12 24                               
  80211a support rate                    :6 9 12 18 24 36 48 54                 
  80211ac mcs                            :9 9 9                                 
  Multicast rate 2g                      :11                                    
  Multicast rate 5g                      :6                                     
  A-MSDU send switch                     :disable                               
  A-MSDU send max-subframes              :2                                     
  --------------------------------------------------------------
Table 12-38  Description of the display radio config command output

Item

Description

Administrate status

Management status.

Channel

Channel.

Channel bandwidth

Bandwidth of a channel.

Power level

Power level of a radio.

Power(dBm)

Power of a radio, in dBm.

Available antenna number

Number of available antennas.

Join load-balance-group

Balancing group that a radio has joined.

Radio device detect function

Whether the radio device detection function is enabled.

Attack Detect

Attack detection mode.

Bridge switch

Whether the bridge function is enabled.

Bridge mode

Bridge mode.

Bridge whitelist switch

Whether the bridge whitelist is enabled.

Bind bridge whitelist ID

Whitelist ID bound to a radio.

Bind bridge whitelist name

Whitelist name bound to a radio.

Bridge stp switch

Whether STP is enabled for the bridge.

Antenna gain(dbi)

Antenna gain, in dBi.

Profile ID

ID of a radio profile.

Profile name

Name of a radio profile.

Channel mode

Channel mode.

Power mode

Power mode.

Calibrate interval(min)

Radio calibration interval, in minutes.

PER threshold(%)

Packet error rate (PER) threshold of the radio, in percentage (%).

Conflict rate threshold(%)

Collision rate threshold of the radio, in percentage (%).

RTS/CTS threshold(Byte)

RTS/CTS threshold, in bytes.

Fragmentation threshold(Byte)

Packet fragmentation threshold of the radio, in bytes.

Short retry number limit

Number of retransmissions of a small frame.

Long retry number limit

Number of retransmissions of a large frame.

Support short preamble

Whether short preamble is supported.

DTIM interval (Beacon interval numbers)

Delivery traffic indication message (DTIM) interval, which is the number of Beacon intervals.

Beacon interval (ms)

Beacon interval, in ms.

WMM profile ID

ID of the Wi-Fi Multimedia (WMM) profile.

WMM profile name

Name of a WMM profile.

Interference detect switch

Whether interference detection is enabled.

Calibrate switch

Whether radio calibration is enabled.

Calibrate scan-cycle(s)

The probe interval for radio calibration.

Common frequency disturb threshold(%)

Threshold for co-channel interference, in percentage (%).

Adjacent frequency disturb threshold(%)

Threshold for adjacent-channel interference, in percentage (%).

Radio device report duration(second)

Report interval of radio devices, in seconds.

RTS/CTS mode

RTS/CTS working mode.

Wifi-light mode

Wireless LED working mode.

802.11n guard interval mode

Guard interval (GI) mode

802.11n A-MPDU length limit

The maximum length of an aggregated MPDU
Channel scan-frequency(ms) Channel scanning interval.
Channel scan-time(ms) Channel scanning duration.

802.11ac guard interval mode

GI mode for 802.11ac radios.

To set this parameter, run the guard-interval-mode (for AC) command.

802.11ac A-MPDU length limit

Maximum length of the A-MPDU for 802.11ac radios.

To set this parameter, run the 80211ac a-mpdu command.

Legacy station access

Whether to permit access of legacy terminals.

To set this parameter, run the legacy-station enable (for AC) command.

80211bg basic rate

802.11bg basic rate set.

To set this parameter, run the 80211bg basic-rate (for AC) command.

80211bg support rate

802.11bg supported rate set.

To set this parameter, run the 80211bg supported-rate (for AC) command.

80211a basic rate

802.11a basic rate set.

To set this parameter, run the 80211a basic-rate command.

80211a support rate

802.11a supported rate set.

To set this parameter, run the 80211a supported-rate command.

80211ac mcs

MCS value for 802.11ac radios.

To set this parameter, run the 80211ac supported-mcs command.

Multicast rate 2g

Multicast rate of wireless packets on the 2.4 GHz radio.

To set this parameter, run the multicast-rate 2g command.

Multicast rate 5g

Multicast rate of wireless packets on the 5 GHz radio.

To set this parameter, run the multicast-rate 5g command.

A-MSDU send switch

Whether to enable the function of sending 802.11 packets in A-MSDU mode.

A-MSDU send max-subframes

Maximum number of subframes that can be aggregated into an A-MSDU.

display radio-profile (for AC)

Function

The display radio-profile command displays the configuration of a radio profile.

Format

display radio-profile { all | id profile-id | name profile-name }

Parameters

Parameter

Description

Value

all

Displays configurations of all radio profiles.

-

id profile-id

Specifies the radio profile ID.

The radio profile ID must exist.

name profile-name

Specifies the radio profile name.

The radio profile name must exist.

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

None

Example

# Display the configuration of radio profile named huawei.

<Huawei> display radio-profile name huawei
  Profile ID                             :0                                     
  Profile name                           :huawei                                 
  Channel mode                           :auto                                  
  Power mode                             :auto                                  
  Calibrate interval(min)                :5                                     
  PER threshold(%)                       :30                                    
  Conflict rate threshold(%)             :60                                    
  RTS/CTS threshold(Byte)                :2347                                  
  Fragmentation threshold(Byte)          :2346                                  
  Short retry number limit               :7                                     
  Long retry number limit                :4                                     
  Support short preamble                 :support                               
  DTIM interval (Beacon interval numbers):1                                     
  Beacon interval(ms)                    :100                                   
  WMM profile ID                         :0                                     
  WMM profile name                       :wmm                                   
  Interference detect switch             :disable                               
  Calibrate switch                       :enable                                
  Calibrate scan-cycle(s)                :60                                    
  RTS/CTS mode                           :CTS-TO-SELF                           
  Wifi-light mode                        :signal-strength                       
  802.11n guard interval mode            :normal                                
  802.11n A-MPDU length limit            :3                                     
  Channel scan-frequency(ms)             :10000                                 
  Channel scan-time(ms)                  :60                                    
  802.11ac guard interval mode           :normal                                
  802.11ac A-MPDU length limit           :7                                     
  Legacy station access                  :enable                                
  80211bg basic rate                     :1 2                                   
  80211bg support rate                   :1 2 5 6 9 11 12 18 24 36 48 54        
  80211a basic rate                      :6 12 24                               
  80211a support rate                    :6 9 12 18 24 36 48 54                 
  80211ac mcs                            :9 9 9                                 
  Multicast rate 2g                      :11                                    
  Multicast rate 5g                      :6                                     
  A-MSDU send switch                     :disable                               
  A-MSDU send max-subframes              :2                                     
  -----------------------------------------------------------------------  

# Display configurations of all radio profiles.

<Huawei> display radio-profile all
  ----------------------------------------------------                          
   ID     Name                                                                  
  ----------------------------------------------------                          
   0      lw                                                                    
   1      t                                                                     
  ----------------------------------------------------                          
   Total: 2   
Table 12-39  Description of the display radio-profile command output

Item

Description

Profile ID

Profile ID.

Profile name

Profile name.

Channel mode

Channel mode.

Power mode

Power mode.

Calibrate interval(min)

Radio calibration interval, in minutes.

PER threshold(%)

Packet error rate threshold, in percentage (%).

Conflict rate threshold(%)

Collision rate threshold, in percentage (%).

RTS/CTS threshold(Byte)

Request To Send/Clear To Send (RTS/CTS) threshold.

Fragmentation threshold(Byte)

Packet fragmentation threshold.

NOTE:
V200R007C00 does not support fragmentation threshold.

Short retry number limit

Number of retransmissions of a small frame.

Long retry number limit

Number of retransmissions of a large frame.

Support short preamble

Whether short preamble is supported.

DTIM interval (Beacon interval numbers)

DTIM interval.

Beacon interval(ms)

Interval for sending Beacon frames.

WMM profile ID

ID of the Wi-Fi Multimedia (WMM) profile bound to the radio profile.

WMM profile name

Name of the WMM profile bound to the radio profile.

Interference detect switch

Whether interference detection is enabled.
  • enable: Interference detection is enabled.
  • disable: Interference detection is disabled.

To enable interference detection, run the interference detect enable command.

Calibrate switch

Whether radio calibration is enabled.
  • enable: Local radio calibration is enabled.
  • disable: Local radio calibration is disabled.

Calibrate scan-cycle(s)

The channel probe interval for radio calibration

Common frequency disturb threshold(%)

Common frequency disturb threshold, in percentage (%).

To set the common frequency disturb threshold, run the set ap common-frequency interference threshold command.

Adjacent frequency disturb threshold(%)

Adjacent frequency disturb threshold, in percentage (%).

To set the adjacent frequency disturb threshold, run the set ap adjacent-frequency interference threshold command.

Station disturb threshold

STA disturb threshold, in percentage (%).

To set the STA disturb threshold, run the set station interference threshold command.

RTS/CTS mode

RTS/CTS working mode.

Wifi-light mode

Light mode.

802.11n guard interval mode

Guard-interval Mode.

802.11n A-MPDU length limit

Maximum length of an A-MPDU.

Channel scan-frequency(s) Channel scanning interval.
Channel scan-time(ms) Channel scanning duration.

ID

Profile ID.

Name

Profile name.

Total

Number of profiles.

802.11ac guard interval mode

GI mode for 802.11ac radios.

To set this parameter, run the guard-interval-mode (for AC) command.

Legacy station access

Whether to permit access of legacy terminals.

To set this parameter, run the legacy-station enable (for AC) command.

80211bg basic rate

802.11bg basic rate set.

To set this parameter, run the 80211bg basic-rate (for AC) command.

80211bg support rate

802.11bg supported rate set.

To set this parameter, run the 80211bg supported-rate (for AC) command.

80211a basic rate

802.11a basic rate set.

To set this parameter, run the 80211a basic-rate command.

80211a support rate

802.11a supported rate set.

To set this parameter, run the 80211a supported-rate command.

80211ac mcs

MCS value for 802.11ac radios.

To set this parameter, run the 80211ac supported-mcs command.

Multicast rate 2g

Multicast rate of wireless packets on the 2.4 GHz radio.

To set this parameter, run the multicast-rate 2g command.

Multicast rate 5g

Multicast rate of wireless packets on the 5 GHz radio.

To set this parameter, run the multicast-rate 5g command.

A-MSDU send switch

Whether to enable the function of sending 802.11 packets in A-MSDU mode.

A-MSDU send max-subframes

Maximum number of subframes that can be aggregated into an A-MSDU.

display radio status (for AC)

Function

The display radio status command displays status of a specified AP radio.

Format

display radio status ap-id ap-id radio-id radio-id

Parameters

Parameter

Description

Value

ap-id ap-id

Specifies an AP ID.

The AP ID must exist.

radio-id radio-id

Specifies radio ID of an AP.

The radio ID must exist.

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

The display radio status command can display status of specified AP radios, which facilitates AP radio management.

Example

# Display the status of AP 0's radio 0.

<Huawei> display radio status ap-id 0 radio-id 0
   Radio status                                                                 
  -----------------------------------------------------------------------       
   Radio status: on                                                             
  -----------------------------------------------------------------------       
Table 12-40  Description of the display radio status command output

Item

Description

radio-status

Radio status.
  • on: enabled
  • off: disabled

display service-batch

Function

The display service-batch command displays the service configurations of a specified radio on APs of a specified type.

Format

display service-batch ap-type { id ap-type-id | name ap-type-value } radio radio-id

Parameters

Parameter

Description

Value

ap-type id ap-type-id

Specifies the ID of an AP type.

The value is an integer that ranges from 0 to 255.

ap-type name ap-type-value

Specifies the AP type.

The AP type must exist.

You can run the display ap-type all command to view types of all APs.

radio radio-id

Specifies the radio ID.

The value is an integer that ranges from 0 to 3.

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

This command displays the radio profile and service set bound to a specified radio on APs of a specified type that are configured using the service-batch or service-batch modify command.

Example

# Display the batch service configuration of radio 0 on AP6010SN-GN APs.

<Huawei> display service-batch ap-type name ap6010sn-gn radio 0
  ----------------------------------------------------------------              
  AP type: ap6010sn-gn                                                          
  AP type ID: 17                                                                
  Radio ID: 0                                                                   
  Radio profile name: rp01                                                   
  Service-set ID list: 1                                                        
  ---------------------------------------------------------------- 
Table 12-41  Description of the display service-batch command output

Item

Description

AP type

AP type.

AP type ID

ID of an AP type.

Radio ID

Radio ID.

Radio profile name

Name of a radio profile.

Service-set ID list

List of service set IDs.

display service-set (for AC)

Function

The display service-set command displays service set information.

Format

display service-set { all | id service-set-id | name service-set-name | ssid ssid }

Parameters

Parameter

Description

Value

all

Displays information about all service sets.

-

id service-set-id

Specifies the ID of a service set.

The value must be an existing service set ID.

name service-set-name

Specifies the name of a service set.

The value must be an existing service set name.

ssid ssid

Specifies the SSID of a service set.

The value must be an existing SSID.

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

You can run this command to view information service set information.

Example

# Display information about all service sets.

<Huawei> display service-set all 
  ----------------------------------------------------------------------------  
  ID      Name                            SSID                                  
  0       lw                              abc                        
  1       lw2                             abcd                       
  ----------------------------------------------------------------------------  
  Total: 2   

# Display information about service set 1.

<Huawei> display service-set id 1
 ----------------------------------------------------------------------------  
  Service-set ID                   : 0                                          
  Service-Set name                 : test                                       
  SSID                             : apple_ac_10310227                          
  Hide SSID                        : disable                                    
  User isolate                     : disable                                    
  Type                             : service                                    
  Maximum number of user           : 32                                         
  Association timeout(min)         : 5                                          
  Traffic profile name             : traffic                                    
  Security profile name            : security0                                  
  Wlan-ess interface               : Wlan-ess0                                  
  Igmp mode                        : off                                        
  Service-vlan                     : 200                                        
  IPSG switch                      : disable                                    
  DHCP trust port                  : disable                                    
  DAI switch                       : disable                                    
  Temporary-management switch      : disable                                    
  Learn client ip-address          : enable                                     
  ----------------------------------------------------------------------------  

# Display information about service set with the SSID of abcd.

<Huawei> display service-set ssid abcd
  Service-set List:                                                             
  ----------------------------------------------------------------------------  
  ID      Name                                                                  
  1       abcd                                                                  
  ----------------------------------------------------------------------------  
  Total: 1 
Table 12-42  Description of the display service-set command output

Item

Description

ID

ID of a service set.

Name

Specifies the name of a service set.

SSID

Specifies the SSID of a service set.

Service-set ID

ID of a service set.

Service-Set name

Specifies the name of a service set.

Hide SSID

Whether the SSID is hidden.

User isolate

Whether Layer 2 user isolation is enabled.

Type

Type of a service set, which can be service, ac-management, or ap-management.

Maximum number of user

Maximum number of users.

Association timeout(min)

Association timeout period.

Traffic profile name

Name of a traffic profile.

Security profile name

Name of a security profile.

Wlan-ess interface

Number of a WLAN-ESS interface.

Igmp mode

IGMP mode, which can be proxy, snooping, or off.

Service-vlan

Service VLAN.

IPSG switch

Status of IPSG.
  • disable: disables IPSG.
  • enable: Enables IPSG.

DHCP trust port

DHCP trusted interface enabled.

DAI switch

Whether DAI is enabled.

Temporary-management switch

Whether to enable management VAP and antenna alignment VAP for offline APs.

Learn client ip-address STA address learning.

display station assoc-info (for AC)

Function

The display station assoc-info command displays information about associated STAs.

Format

display station assoc-info { sta mac-address | ap ap-id [ radio radio-id [ service-set service-set-id ] ] | all }

Parameters

Parameter

Description

Value

sta mac-address

Displays information about an associated STA with a specified MAC address.

The value is in H-H-H format. An H is a hexadecimal number of four digits.

ap ap-id

Displays information about a STA associated with a specified AP.

The value is an integer that ranges from 0 to 15.

radio radio-id

Displays information about associated STAs on a specified radio.

The value is an integer that ranges from 0 to 3.

service-set service-set-id

Displays information about STAs in a specified service set.

The value is an integer that ranges from 0 to 15.

all

Displays access information about all STAs.

-

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

You can run this command to view information about associated STAs.
  • To view information about a specified STA, ensure that the STA has been associated with an AP.
  • To view information about all STAs associated with a specified AP, ensure that the AP has been added to the AC and is in normal state.
  • To view information about all STAs associated with a specified AP and radio, ensure that the AP has been added to the AC, is in normal state, and support the radio.
  • To view information about all STAs associated with a specified AP, radio, and service set, ensure that the AP has been added to the AC, is in normal state, and support the radio, and the service set has been bound to the radio on the AP.

Example

# Display information about an associated STA with MAC address 4016-9f14-f25d.

<Huawei> display station assoc-info sta 4016-9f14-f25d
  ------------------------------------------------------------------------------
  Station mac-address                       : 4016-9f14-f25d                    
  Station ip-address                        : 0.0.0.0                           
  Station gateway                           : 0.0.0.0                           
  Associated SSID                           : lx209762                          
  Station online time(ddd:hh:mm:ss)         : 000:00:04:20                      
  The upstream SNR(dB)                      : 30.0                              
  Station connect rate(Mbps)                : 23                                
  Station connect channel                   : 1                                 
  Station inactivity time(ddd:hh:mm:ss)     : 000:00:00:00                      
  Station current state                                                         
    Authorized for data transfer            : YES                               
    Qos enabled                             : YES                               
    ERP enabled                             : YES                               
    HT rates enabled                        : No                                
    Power save mode enabled                 : YES                               
    Auth reference held                     : No                                
    UAPSD enabled                           : No                                
    UAPSD triggerable                       : No                                
    UAPSD SP in progress                    : No                                
    This is an ATH node                     : No                                
    WDS workaround req                      : No                                
    WDS link                                : No                                
  Station's HT capability                   : WPM                                 
  Station ERP element                       : 0                                 
  Station capabilities                      : ESs                               
  Station's RSSI(dBm)                        : -66                       
  Station's Noise(dBm)                      : -109                              
  Station's radio mode                      : 11b                               
  Station's AP ID                           : 6                                 
  Station's Radio ID                        : 0                                 
  Station's Authentication Method           : OPEN                              
  Station's Cipher Type                     : NO CIPHER                         
  Station's User Name                       : d4206df4f37e                      
  Station's Vlan ID                         : 28                                
  Station's Channel Band-width              : 20MHz                             
  Station's asso BSSID                      : dcd2-fc9a-2110                    
  Station's state                           : Asso with auth                    
  Station's Qos Mode                        : NULL                              
  Station's HT Mode                         : -                                 
  Station's MCS value                       : 0                                 
  Station's NSS value                       : 0                                 
  Station's Short GI                        : support                           
  Station's roam state                      : No
  ------------------------------------------------------------------------------
# Display information about the STAs associated with AP 1.
<Huawei> display station assoc-info ap 1
  AP/Rf/WLAN: AP ID/Radio ID/WLAN ID            
  Rx/Tx: link receive rate/link transmit rate(Mbps)                             
  ------------------------------------------------------------------------------
  STA MAC         AP/Rf/WLAN Rx/Tx     Mode  RSSI   IP address                  
  SSID                                                                          
  ------------------------------------------------------------------------------
  14cf-9208-9abf  1/0/1      3/41      11n   -72    10.1.1.254                  
  deng                                                                       
  ------------------------------------------------------------------------------
  Total stations: 1
# Display information about the associated STAs on radio 0 of AP 1.
<Huawei> display station assoc-info ap 1 radio 0
  AP/Rf/WLAN: AP ID/Radio ID/WLAN ID                                            
  Rx/Tx: link receive rate/link transmit rate(Mbps)                             
  ------------------------------------------------------------------------------
  STA MAC         AP/Rf/WLAN Rx/Tx     Mode  RSSI   IP address                  
  SSID                                                                          
  ------------------------------------------------------------------------------
  14cf-9208-9abf  1/0/1      4/43      11n   -70    10.1.1.254                  
  deng                                                                       
  ------------------------------------------------------------------------------
  Total stations: 1 
# Display information about the STAs associated with service-set 0 bound to radio 0 on AP 1.
<Huawei> display station assoc-info ap 1 radio 0 service-set 0
  AP/Rf/WLAN: AP ID/Radio ID/WLAN ID                                            
  Rx/Tx: link receive rate/link transmit rate(Mbps)                             
  ------------------------------------------------------------------------------
  STA MAC         AP/Rf/WLAN Rx/Tx     Mode  RSSI   IP address                  
  SSID                                                                          
  ------------------------------------------------------------------------------
  14cf-9208-9abf  1/0/1      4/43      11n   -70    10.1.1.254                  
  deng                                                                       
  ------------------------------------------------------------------------------
  Total stations: 1 
Table 12-43  Description of the display station assoc-info command output

Item

Description

STA MAC

MAC address of the STA.

AP ID

AP with the STA is associated.

RADIO ID

Radio with which the STA is associated.

AP/Rf/WLAN

ID of the AP/radio/VAP to which the STA connects.

Rx/Tx

Rates at which an AP receives packets from and sends packets to STAs.

Mode

Radio mode of the STA.

RSSI

RSSI of the STA.

IP address

IP address of the STA.

SSID

SSID with which the STA is associated.

Total stations

Total number of STAs.

Station mac-address MAC address of a STA.
Station ip-address IP address of a STA.

Station gateway

Gateway address of a STA.
NOTE:

If the device obtains the STA's gateway address through DHCP, the parameter displays as the obtained gateway address; otherwise, the parameter displays as 0.0.0.0.

Associated SSID SSID of a service set with which a STA is associated.
Station online time(ddd:hh:mm:ss) Online duration of a STA, in the format of ddd:hh:mm:ss.
The upstream SNR(dB) Upstream signal noise ratio of a STA, in dB.
The upstream aggregate receive power(dBm) Upstream receive power of a STA, in dBm.
Station connect rate(Mbps) Connection rate of a STA, in Mbit/s.
Station connect channel Channel used by a STA.
Station inactivity time(ddd:hh:mm:ss) Idle duration of a STA, in the format of ddd:hh:mm:ss.
Station current state Current status of a STA.
Authorized for data transfer Whether a STA is authenticated.
Qos enabled Whether QoS is enabled on a STA.
ERP enabled Whether Effective radiated power (ERP) is enabled on a STA to increase the physical-layer transmission speed.
HT rates enabled Whether 802.11n is enabled on a STA.
Power save mode enabled Whether the power saving mode is enabled on a STA.
Auth reference held Whether the authentication reference flag is set.
UAPSD enabled Whether UAPSD is enabled.
UAPSD triggerable UAPSD can be triggered, waiting for a STA to send a trigger frame to the AP.
UAPSD SP in progress Whether the UAPSD mode is in the service period (SP).
This is an ATH node Whether the wireless network adapter uses the atheros chip.
WDS workaround req Whether a patch is used to fix bugs of atheros owl series chips in WDS scenarios.
WDS link STA that is a node on the WDS link.
Station's HT capability HT capability of a STA.
Station ERP element ERP of a STA, in dBm.
Station capabilities Capabilities of a STA.
Station's RSSI(dBm) Received signal strength indicator (RSSI) of a STA, in dBm.

Station's Noise(dBm)

Interference signal strength of a STA, in dBm.

Station's radio mode Radio mode of a STA.
Station's AP ID ID of the AP that a STA associates with.
Station's Radio ID Radio ID of a STA.
Station's Authentication Method Authentication mode of a STA.
Station's Cipher Type Encryption mode of a STA.
Station's User Name User name of a STA.
Station's Vlan ID VLAN ID of a STA.
Station's Channel Band-width Channel bandwidth of a STA.
Station's asso BSSID BSSID that the STA associates with.
Station's state Status of the STA.
Station's Qos Mode QoS mode of the STA.
Station's HT Mode HT mode of the STA.
  • 1: HT20
  • 2: HT40
  • 3: VHT80
  • -: The STA does not support the HT mode.
Station's MCS value MCS value of the STA.
Station's Short GI Whether the STA supports the short GI.
Station's roam state Roaming status of the STA.

display station assoc-num (for AC)

Function

The display station assoc-num command displays the number of STAs associated with a specified service set or AP.

Format

display station assoc-num [ service-set service-set-id | ap ap-id [ radio radio-id ] | 2.4g | 5g ]

Parameters

Parameter

Description

Value

ap ap-id

Displays the number of STAs associated with a specified AP.

The value is an integer that ranges from 0 to 15.

radio radio-id

Displays the number of STAs associated with a specified radio.

The value is an integer that ranges from 0 to 3.

service-set service-set-id

Displays the number of STAs associated with a specified service set.

The value is an integer that ranges from 0 to 15.

2.4g

Displays the number of STAs associated with the 2.4 GHz radio.

-
5g

Displays the number of STAs associated with the 5 GHz radio.

-

Views

All views

Default Level

1: Monitoring level

Usage Guidelines

  • To view the number of STAs associated with a specified service set, ensure that the service set has been created using the service-set (for AC) { name service-set-name | id service-set-id } * command.
  • To view the number of STAs associated with a specified AP, ensure that the AP has been added to the AC and is in normal state.

Example

# Display the number of STAs associated with service set 0.

<Huawei> display station assoc-num service-set 0
  Number of station: 1
# Display the number of STAs associated with AP 1.
<Huawei> display station assoc-num ap 1
  Number of station: 1
# Display the number of STAs associated with radio 0 on AP 1.
<Huawei> display station assoc-num ap 1 radio 0
  Number of station: 1
# Display the number of STAs associated with the 2.4 GHz radio.
<Huawei> display station assoc-num 2.4g
  2.4g associated stations number: 0
# Display the number of STAs associated with the 5 GHz radio.
<Huawei> display station assoc-num 5g
  5g associated stations number: 0 
Table 12-44  Description of the display station assoc-num command output