No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

ES3000 V3 NVMe PCIe SSD User Guide 20

This document provides the product information about the Huawei ES3000 V3 PCIe SSD (ES3000 V3 for short) and describes how to install, configure, operate, and maintain the ES3000 V3.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Installing ES3000 V3

Installing ES3000 V3

This topic describes how to install the ES3000 V3.

Operation Scenario

Preparations

  • Stop all services on the server and back up data.
  • Unpack and inspect the devices.

    Check that the items shipped are complete and intact based on the following list:

    • ES3000 V3
    • Quick Start Guide
    • Warranty card
  • Tools

    • ESD gloves

      Used to prevent ESD damage when you insert, remove, or hold the ES3000 V3 or a precision device.

Pay attention to the following in Linux:

  • Do not perform direct read or write operations on a raw SSD to avoid processing the wrong SSD due to a changed drive letter. Restarting the server, installing or uninstalling the SSD driver, inserting and removing the SSD may change the SSD drive letter.
  • If you have to perform direct read or write operations on a raw SSD, use the hioadm info command to check the SSD information and confirm the drive letter through the SSD SN.
  • It is recommended that you use the mount command to mount the SSD partitions to a specified path before performing read and write operations. To ensure normal release of system resources, use the unmount command to cancel the mounted SSD partitions before installing or uninstalling the driver, and inserting or removing the SSD.
  • You can also add information to the /etc/fstab file so that SSD partitions are automatically mounted during system startup, driver installation and uninstallation, and SSD insertion and removal. For details, run the man fstab command to view help information. After enabling the automatic mounting of SSD partitions, you do not need to run the umount command before installing or uninstalling the driver, and inserting or removing the SSD.

Procedure

  • Install the ES3000 V3 NVMe PCIe SSD.
    1. Wear ESD gloves.
    2. Take the ES3000 V3 out of the ESD bag. Check whether a 2.5-inch or 3.5-inch hard disk tray is used.

      • For a 2.5-inch hard disk tray, go to 3.
      • For a 3.5-inch hard disk tray, go to 5.

    3. Place the ES3000 V3 into the hard disk tray. See step (1) in Figure 3-2.
    4. Use four screws to secure the ES3000 V3 to the hard disk tray. See step (2) in Figure 3-2. Then go to 8.

      Figure 3-2  Placing the ES3000 V3 into the hard disk tray

    5. Place the ES3000 V3 to the converter. See step (1) in Figure 3-3.
    6. Use two screws to secure the ES3000 V3 to the converter. See step (2) in Figure 3-3.

      Figure 3-3  Securing the ES3000 V3 to the converter

    7. Use four screws to secure the ES3000 V3 to the hard disk tray. See step (3) in Figure 3-4 and (4) in Figure 3-5.

      Figure 3-4  Securing the ES3000 V3 to the hard disk tray (1)
      Figure 3-5  Securing the ES3000 V3 to the hard disk tray (2)

    8. Open the ejector lever and push the ES3000 V3 into the server until it does not move. See step (1) in Figure 3-6.
    9. Close the ejector lever to push the ES3000 V3 into place. See step (2) in Figure 3-6.

      Figure 3-6  Installing the ES3000 V3

  • Install the ES3000 V3 NVMe PCIe SSD card on a riser card.
    1. Wear ESD gloves.
    2. Turn off the power to the server and remove the chassis cover.
    3. Take the ES3000 V3 out of the ESD bag.
    4. Hold the upper edge of the ES3000 V3, align its connecting part with a PCIe slot on the riser card, and insert the ES3000 V3 slowly into the PCIe slot. See Figure 3-7.

      Figure 3-7  Installing the ES3000 V3 on a riser card

    5. Install the riser card in the server. For details, see related server manuals.
    6. Turn on the power to the server.
  • Install the ES3000 V3 NVMe PCIe SSD card on the mainboard.
    1. Wear ESD gloves.
    2. Turn off the power to the server and remove the chassis cover.
    3. Hold the upper edge of the ES3000 V3, align its connecting part with the PCIe slot, and vertically insert the ES3000 V3 downwards into the PCIe slot. See Figure 3-2.

      Figure 3-8  Installing the ES3000 V3 on the mainboard

    4. Turn on the power to the server.

Follow-up Procedure

After the ES3000 V3 is connected to power, the startup process takes about 30 seconds.

If the active indicator associated with the ES3000 V3 NVMe PCIe SSD is on and the fault indicator is off, the SSD hardware is installed successfully.

If the green indicator (active indicator) on the ES3000 V3 NVMe PCIe SSD is on and the orange indicator (fault indicator) is off, the SSD hardware is installed successfully.

Translation
Download
Updated: 2019-03-12

Document ID: EDOC1000101091

Views: 64920

Downloads: 1259

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next