No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search


To have a better experience, please upgrade your IE browser.


OceanStor 2200 V3 and 2600 V3 Storage System V300R005 Command Reference 06

"Based on the CLI provided by the DeviceManager, this document describes how to use variouscommands classified by functions and how to set the CLI and manage the storage system throughthese commands."
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
show hyper_metro_pair general

show hyper_metro_pair general


The show hyper_metro_pair general command is used to query HyperCluter pairs.


show hyper_metro_pair general pair_id=?





pair_id=? ID of the HyperMetro pair.

Run the "show hyper_metro_pair general" command to obtain the value.



Usage Guidelines

OceanStor 2200 V3 storage system do not support this command.


  • To query all HyperCluter pairs in the device, run the following command.

    admin:/>show hyper_metro_pair general
    ID Health Status Running Status Domain Name Type Size Role Local Name Remote Name
    ---------------- ------------- -------------- ------ ----- ------------ ------------------ - -------------------- --------
    200bc79b99520000 Normal Normal HCD001 LUN 100.000GB Preferred LUN001 extLun001
    200bc79b99520002 Normal Normal HCD002 FS 10.000GB Non-preferred FS001 extFS001
  • To query HyperMetro pair "200bc79b99520000", run the following command.

    admin:/>show hyper_metro_pair general pair_id=200bc79b99520000
    ID : 200bc79b99520000
    Health Status : Normal
    Running Status : Normal
    Link Status : Linkup
    Domain ID : 1
    Domain Name : HCD001
    Type : LUN
    Size : 100.000GB
    WWN : 200bc78945612300
    IP(s) : --
    Role : Preferred
    Local ID : 5
    Local Name : LUN005
    Local Data Status : Consistent
    Local Access Status : Read And Write
    Remote ID : 5
    Remote Name : extLUN005
    Remote Data Status : Consistent
    Remote Access Status : Read And Write
    Recovery Policy : Automatic
    Sync Progress(%) : --
    Sync Direction : --
    Sync Rate : Middle
    Start Time : 2013-12-22/17:18:32 UTC+08:00
    End Time : 2013-12-22/17:18:32 UTC+08:00
    Consistency Group ID : 1
    Consistency Group Name : cg001

System Response

The following table describes the parameter meanings.




ID of the HyperMetro pair,64bits.

Health Status

Health status: Normal or Fault.

Running Status

Running status: Normal, Synchronizing, To Be Synchronized, Pause, Forced Start or Invalid.

Link Status

Link status: Linkup or Linkdown.

Domain ID

ID of the HyperMetro domain.

Domain Name

Name of the HyperMetro domain.


Resource type: LUN or FS.


Resource size.




IP address of the FS share service.


Primary or Secondary/Preferred or Non-preferred. A/P indicates active/passive, and A/A indicates arbitration is required.

Local ID

ID of the local resource.

Local Name

Name of the local resource.

Local Data Status

Local data status: Consistent or Inconsistent.

Local Access Status

Local host access status:No Access or Read and Write.

Remote ID

ID of the remote resource.

Remote Name

Name of the remote resource.

Remote Data Status

Remote data status:Consistent or Inconsistent.

Remote Access Status

Remote host access status:No Access, Read Only or Read and Write.

Recovery Policy

Recovery policy:Automatic or Manual.

Sync Progress(%)

Synchronization progress (%): 0 to100 (valid for LUNs only).

Sync Direction

Synchronization direction: Local to Remote or Remote to Local.

Sync Rate

Synchronization rate: Highest, High, Middle, Low.

Start Time

Start time of the last synchronization.

End Time

End time of the last synchronization.

Consistency Group ID


Consistency Group Name

CG name.

Updated: 2019-07-22

Document ID: EDOC1000106139

Views: 319472

Downloads: 210

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Previous Next