No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

KunLun 9016 V100R001 User Guide 12

This document describes the appearance, specifications, parameters, and structure of the KunLun 9016, and how to install an OS, replace parts, and install, remove, configure, and troubleshoot the server.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Using the Local KVM

Using the Local KVM

Scenarios

Connect the 9016 to the local KVM for local management and maintenance of the server.

With the local KVM, you can log in to the central management console (CMC) CLI, log in to the operating system (OS) of a basic partition unit (BPU), mount a DVD drive to a BPU, and connect to a BPU or a serial port using Serial over LAN (SOL).

Prerequisites

Conditions

You have logged in to the CMC CLI.

Data

You have obtained the following data:

  • User name and password for logging in to the CMC
  • User name and password for logging in to the BPU to be connected

Procedure

  1. Connect a mouse and a keyboard to two USB ports on the central management enclosure (CME) respectively.
  2. Connect a monitor to the video graphics array (VGA) port on the CME by using a VGA cable.

    The main screen of the KVM is displayed, as shown in Figure 9-9.

    Figure 9-9 Main screen

    On the main screen:

    • Press , , , or to select of a BPU, and press Enter to access the OS of the BPU.
    • Press , , , or to select of a BPU, and press Enter to mount the DVD drive in the CME to the BPU. It takes 5 to 6 seconds to mount the DVD drive to a BPU. During the mounting process, do not press Enter again. The color of the DVD drive indicates its status:
      • indicates that the DVD drive is detected.
      • indicates that the DVD drive is working.
    • After finishing using the DVD drive, press , , , or to select, press Enter, and press Y when prompted to disconnect the DVD drive. After the DVD drive is in the Ready state, take out the DVD drive. Do not take out the DVD drive when it is in the Work state.
    NOTE:
    • If the remote DVD drive is mounted on the CMC WebUI, the local DVD drive cannot be mounted. To use the local DVD drive, unmount the remote DVD drive first.
    • After mouse acceleration is enabled on the remote KVM, the local KVM does not support mouse scroll wheel operations. If scroll wheel operations are required, disable mouse acceleration on the remote KVM.
    • An image or folder can be mounted on the remote KVM only after the local DVD drive is disconnected and the DVD drive is in the Ready state.
    • The local KVM can be used only after KVM VMM encryption is disabled on the CMC WebUI.

  3. Perform an operation on the menu based on service requirements. For example, press Ctrl+S.

    The SOL screen is displayed, showing the following information:

    *=====================================================================* 
    *             Welcome to SMM SOL Server                               * 
    *     Please log in with SMM account and password.                    * 
    *=====================================================================* 
     
     
    user name:
    NOTE:

    To return to the previous screen, press Ctrl+R. To return to the main screen of the KVM, press Ctrl+Shift+Alt.

  4. Enter the user name and password for logging in to the CMC.

    The screen for selecting a BPU number is displayed.

    Log in Success! 
     
    *=============================================================================== 
          please input the SOL Node1~Node8(1 ~ 8) and COM#(n) 
          Node: 1:SCE1-BPUB                       2:SCE1-BPUA 
                3:SCE2-BPUB                       4:SCE2-BPUA 
          press Ctrl+R to return                              
    *=============================================================================== 
     
     
    Node1~Node8(1 ~ 4) 
    Please input your choice:

    The numbers on the screen are described as follows:

    1 to 4 indicate BPUs 1 to 4 respectively.

  5. Enter the number of the BPU to be connected (for example, enter 1), and press Enter.

    All serial ports to be connected are displayed.

    Please input your choice:1 
    1 SYS COM 
    2 BMC COM 
    COM#(1 ~ 2):

  6. Enter the number of the serial port to be connected (for example, enter 1), and press Enter.

    The serial port screen is displayed.

  7. Enter the user name and password for logging in to the BPU.

    On the serial port screen, you can configure and query data.

Translation
Download
Updated: 2019-05-20

Document ID: EDOC1000111827

Views: 104098

Downloads: 250

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next