No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S1720GFR, S2700, S5700, and S6720 V200R010C00 Web-based Configuration Guide

This document describes the configuration and maintenance of device through the web network management system. The web network management system provides the functions of viewing device information and managing the entire system, interfaces, services, ACL, QoS, routes, security, and tools.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Ethernet

Ethernet

Configure these interfaces as required.

Basic Attributes

You can configure and query the basic attributes of Ethernet interfaces.

Context

To identify an interface, you can set the description of the interface. You can query and configure Ethernet interfaces as required.

Procedure

  • Query basic attributes.
    1. Choose Interface Management > Ethernet > Basic Attributes in the navigation tree to open the Basic Attributes page.
    2. Select an interface type from the drop-down list box.
    3. Enter the interface number, for example, 0/0/1 (slot ID/subcard ID/interface number).
    4. Click Query to display all matching records.
  • Configure basic attributes.
    1. Choose Interface Management > Ethernet > Basic Attributes in the navigation tree to open the Basic Attributes page.
    2. Select a record and click Configure. The Configure Basic Attributes page is displayed, as shown in Figure 2-95.

      Figure 2-95  Configure Basic Attributes

      Table 2-51 describes the parameters on the Configure Basic Attributes page.

      Table 2-51  Configure basic attributes

      Parameter

      Description

      Interface name

      Indicates the name of an interface. The interface name cannot be modified. You can select multiple interfaces each time.
      NOTE:

      If only one interface is selected, the configuration of the interface is displayed on the Configure Basic Attributes page. If multiple interfaces are selected, the default settings of the interfaces are displayed. You can select only interfaces of the same type.

      PVID

      Indicates the default VLAN of the interface. This parameter cannot be modified.

      Status

      Indicates the status of the interface, which can be enabled or disabled. By default, the status of an interface is enabled. This parameter is mandatory.

      Link type

      The value cannot be changed.

      Auto-negotiation

      Indicates whether auto-negotiation is enabled. This parameter is mandatory. By default, auto-negotiation is enabled, and the duplex mode or interface rate cannot be configured. If auto-negotiation is disabled, the Duplex and Rate parameters can be configured.

      Duplex

      Indicates the duplex mode of the interface, including full duplex and half duplex. By default, the full duplex mode is enabled on interfaces. This parameter is mandatory.

      To enable an interface to send and receive packets at the same time, enable the full duplex mode on the interface. To disable an interface from sending and receiving packets at the same time, enable the half duplex mode on the interface.
      NOTE:

      A GE electrical interface can work in full duplex, half duplex, or auto-negotiation mode. However, if the speed is set to 1000 Mbit/s, the duplex mode must be full duplex or auto-negotiation. A GE optical interface operates in full duplex mode by default. You can configure it to operate in full duplex mode or auto-negotiation mode.

      Rate

      Indicates the interface speed. This parameter is mandatory.
      NOTE:

      The speed on a GE electrical interface can be 10 Mbit/s, 100 Mbit/s, or 1000 Mbit/s. If the duplex mode is set to half duplex, the interface speed cannot be 1000 Mbit/s. The speed on a GE optical interface can be 100 Mbit/s, 1000 Mbit/s. You can set the speed to 100 Mbit/s, 1000 Mbit/s or enable auto-negotiation.

      Jumbo

      Indicates the length of a jumbo frame. This parameter is optional.

      Combo type

      When the selected interface is set to Combo interface, the Combo type can be configured. The Combo types are classified into auto, copper, and fiber. The default type is auto.

      Description

      Indicates the description of the interface. This parameter is mandatory.

    3. Set parameters.
    4. Click OK.

Interface Statistics

You can view traffic statistics on interfaces, update the statistics, or clear the statistics.

Context

The cleared traffic statistics cannot be restored; therefore, confirm the operation before clearing the traffic statistics.

Procedure

  1. Choose Interface Management > Ethernet > Interface Statistics in the navigation tree to open the Interface Statistics page, as shown in Figure 2-96.

    Figure 2-96  Interface Statistics

  2. Click Refresh to obtain latest traffic statistics.
  3. Select a record and click Clear to clear traffic statistics on a specified interface and refresh the page.
  4. Click Clear All to clear traffic statistics on all interfaces and refresh the page.
  5. Select a record and click Details to view details about the record.

    On the Details page, you can refresh, clear, and close the traffic statistics.

Translation
Download
Updated: 2019-04-18

Document ID: EDOC1000114003

Views: 38389

Downloads: 995

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next