LST3X08BX6E0 (03033GGR/03033GGR-001/03033GGR-002: 8-Port 10GE SFP+ Interface and 24-Port GE SFP Interface Card (X6E, SFP+))

S9300X Series Switches Hardware Description

Rate and give feedback:

Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).

Version Mapping

Table 7-512 Switch chassis and software versions matching the card

Card Name	Part Number	S9300X Chassis
LST3X08BX6E0	03033GGR	S9310X chassis: not supported S9300X-4, S9300X-8, and S9300X-12 chassis: supported in V200R019C00 and later versions NOTE: As for cards manufactured since June 2021: If they are used in V200R019C00, load V200R019SPH029 or a later patch, and load S9300X_V200R019C00SPC500_BOARD_MOD002.mod or a later mod file.
03033GGR-001	S9310X chassis: not supported S9300X-4, S9300X-8, and S9300X-12 chassis: supported in V200R021C10SPC500 and later versions NOTE: If the card is used in V200R019C10SPC500, install V200R019SPH058 or a later patch and S9300X_V200R019C10SPC500_BOARD_MOD003.mod or a later mod file. If the card is used in V200R021C00SPC100 or V200R021C01, install V200R021SPH011 or a later patch.
03033GGR-002	S9310X chassis: not supported S9300X-4, S9300X-8, and S9300X-12 chassis: supported in V200R021C10SPC600 and later versions NOTE: If the card is used in V200R019C10SPC500, install V200R019SPH380 or a later patch and S9300X_V200R019C10SPC500_BOARD_MOD005.mod or a later mod file. If the card is used in V200R021C00SPC100 or V200R021C01, install V200R021SPH180 or a later patch.

Card Name

Part Number

S9300X Chassis

LST3X08BX6E0

03033GGR

S9310X chassis: not supported

S9300X-4, S9300X-8, and S9300X-12 chassis: supported in V200R019C00 and later versions

NOTE:

As for cards manufactured since June 2021:

If they are used in V200R019C00, load V200R019SPH029 or a later patch, and load S9300X_V200R019C00SPC500_BOARD_MOD002.mod or a later mod file.

03033GGR-001

S9310X chassis: not supported

S9300X-4, S9300X-8, and S9300X-12 chassis: supported in V200R021C10SPC500 and later versions

NOTE:

If the card is used in V200R019C10SPC500, install V200R019SPH058 or a later patch and S9300X_V200R019C10SPC500_BOARD_MOD003.mod or a later mod file.
If the card is used in V200R021C00SPC100 or V200R021C01, install V200R021SPH011 or a later patch.

03033GGR-002

S9310X chassis: not supported

S9300X-4, S9300X-8, and S9300X-12 chassis: supported in V200R021C10SPC600 and later versions

NOTE:

If the card is used in V200R019C10SPC500, install V200R019SPH380 or a later patch and S9300X_V200R019C10SPC500_BOARD_MOD005.mod or a later mod file.
If the card is used in V200R021C00SPC100 or V200R021C01, install V200R021SPH180 or a later patch.

Introduction

The LST3X08BX6E0 can be installed in:

Slots 01 to 04 in an S9300X-4 chassis.
Slots 01 to 08 in an S9300X-8 chassis.
Slots 01 to 12 in an S9300X-12 chassis.

Figure 7-227 Appearance of the LST3X08BX6E0

Functions

Table 7-513 Functions of the LST3X08BX6E0

Function	Description
Basic functions	Provides eight 10GE optical ports and twenty-four GE optical ports for data transmission and switching.
Distributed forwarding	Performs concurrent data forwarding using a distributed data plane.
Hot swapping	Supported

Indicators and Ports

Figure 7-228 Indicators on the LST3X08BX6E0 panel

Table 7-514 Indicators on the LST3X08BX6E0 panel

Number	Indicator	Color	Description
1	ACT indicator of a lower optical port	Yellow	Blinking: The port is transmitting and receiving data.
2	ACT indicator of an upper optical port	Yellow	Blinking: The port is transmitting and receiving data.
3	LINK indicator of a lower optical port	Green	Steady on: A link has been established on the port.
4	LINK indicator of an upper optical port	Green	Steady on: A link has been established on the port.
5	RUN/ALM: running status indicator	Green	Steady on: The card is powered on. If the indicator is steady green for no more than 30 seconds, the CPU is being started. If the indicator is steady green for more than 30 seconds, the software is not running. Slow blinking: The card software is running properly. Fast blinking: The card software is starting.
		Red	Steady on: The card has failed and the fault requires manual intervention.
		Yellow	Steady on: The card is powered off. (For example, the card has been forcibly powered off using the power off command or is about to start.)

Figure 7-229 Ports on the LST3X08BX6E0 panel

1	Eight 10GBASE SFP+/1000BASE-X ports
2	Twenty-four 1000BASE-X ports

When a lot of cables are connected to a card, the cable management frame for this slot may not have sufficient space. In this case, deploy cables in three layers that do not cross over each other, and then put the three layers through the cable management frame. See Figure 7-230.
It is not recommended to connect copper cables and optical fibers to the same card because copper cables may block the routes of optical fibers. If copper cables and optical fibers are used on the same card, connect the optical fibers to ports near the left side of the card and the copper cables to ports near the right side, as shown in Figure 7-231.

Figure 7-230 Three layers of cables in a cable management frame

Figure 7-231 Optical fibers and SFP+ cables on the same card

10GBASE SFP+/1000BASE-X port

10GBASE SFP+/1000BASE-X ports support 10GE and GE auto sensing.

Table 7-515 Optical port attributes (GE optical module)

Attribute	Description
Connector type	SFP+
Optical port attributes	Depend on the SFP optical module used. For the optical modules supported by the LST3X08BX6E0 and their attributes, see GE eSFP Optical Modules, GE-CWDM eSFP Optical Modules, and GE-DWDM eSFP Optical Modules.
Standards compliance	IEEE802.3z
Frame format	Ethernet_II, Ethernet_SAP, Ethernet_SNAP
Network protocol	IP

Table 7-516 Optical port attributes (10GE optical module, high-speed cable or SFP+ optical cable)

Attribute	Description
Connector type	SFP+
Optical port attributes	Depend on the SFP+ to SFP+ high-speed cable (1 m, 3 m, 5 m, 10 m), QSFP+ to 4*SFP+ high-speed cable (1 m, 3 m, 5 m), SFP+ optical module, or SFP+ optical cable used. For the optical modules supported by the LST3X08BX6E0 and their attributes, see 10GE SFP+ Optical Modules (OSXD22N00 not supported), 10GE-CWDM SFP+ Optical Modules and 10GE-DWDM SFP+ Optical Modules.
Standards compliance	IEEE 802.3ae
Frame format	Ethernet_II, Ethernet_SAP, Ethernet_SNAP
Network protocol	IP

Table 7-517 Optical port attributes (copper module)

Attribute

Description

Connector type

SFP+

Optical port attributes

Depend on the SFP copper module used.

For details on the copper modules supported by the cards and attributes of the copper modules, see GE SFP Copper Modules (100 Mbit/s and 1000 Mbit/s rates).

Applicable cable

SFP copper module and Ethernet cable

1000BASE-X ports

Table 7-518 lists the attributes of a 1000BASE-X port with an optical module installed.

Table 7-518 Optical port attributes (optical module)

Attribute	Description
Connector type	SFP
Optical port attributes	Depend on the SFP optical module used. For details about optical modules supported by the LST3X08BX6E0 and their attributes, see GE eSFP Optical Modules, GE-CWDM eSFP Optical Modules, and GE-DWDM eSFP Optical Modules.
Standards compliance	IEEE 802.3z
Frame format	Ethernet_II, Ethernet_SAP, Ethernet_SNAP
Network protocol	IP

Table 7-519 lists the attributes of a 1000BASE-X port with a copper module installed.

Table 7-519 Optical port attributes (copper module)

Attribute

Description

Connector type

SFP

Optical port attributes

Depend on the SFP copper module used.

For details on the copper modules supported by the cards and attributes of the copper modules, see GE SFP Copper Modules (100 Mbit/s and 1000 Mbit/s rates).

Applicable cable

SFP copper module and Ethernet cable

Specifications

Table 7-520 Specifications of the LST3X08BX6E0

Item	Description
Physical specifications	Dimensions (H x W x D): 35.1 mm x 397.2 mm x 430.4 mm (1.38 in. x 15.64 in. x 16.95 in.) Weight: 3.2 kg (7.05 lb) Maximum power consumption: 138 W

Item

Description

Physical specifications

Dimensions (H x W x D): 35.1 mm x 397.2 mm x 430.4 mm (1.38 in. x 15.64 in. x 16.95 in.)

Weight: 3.2 kg (7.05 lb)
Maximum power consumption: 138 W

Ordering Information

Card ordering information is subject to updates with product version upgrades. The ordering information provided in this manual is for reference only. To obtain the latest ordering information, contact Huawei switch distributors or Huawei local office.

Table 7-521 Ordering information

Part Number	Card Description	Card Model
03033GGR 03033GGR-001 03033GGR-002	8-Port 10GE SFP+ Interface and 24-Port GE SFP Interface Card (X6E, SFP+)	LST3X08BX6E0

Translation

简体中文

Download

Updated: 2023-10-23

Document ID: EDOC1000138177

Downloads: 671

Average rating:

This Document Applies to these Products

Related Version

Digital Signature File

Digital Signature Authentication Mode

Enterprise

Huawei Cloud

Carrier

Consumer

Corporate

Version Mapping

Introduction

Functions

Indicators and Ports

Specifications

Ordering Information

Related Version

Related Documents

Digital Signature File