LE1D2S04SEC0-4-Port 10GBASE-X and 24-Port 100/1000BASE-X and 8-Port 10/100/1000BASE-T Combo Interface Card (EC, RJ45/SFP/SFP+)

S9300X Series Switches Hardware Description

Rate and give feedback:

Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).

Version Mapping

Table 7-376 Switch chassis and software versions matching the card

Card Name	S9300X Chassis
LE1D2S04SEC0	S9310X chassis: supported in V200R010C00 and later versions S9300X-4, S9300X-8, and S9300X-12 chassis: not supported

Card Name

S9300X Chassis

LE1D2S04SEC0

S9310X chassis: supported in V200R010C00 and later versions

S9300X-4, S9300X-8, and S9300X-12 chassis: not supported

Introduction

The LE1D2S04SEC0 can be installed in:

Slots 01 to 10 in an S9310X chassis.

Figure 7-181 Appearance of the LE1D2S04SEC0

Functions

The LE1D2S04SEC0 provides the following functions:

Communicates with the MPU and works under the control of the MPU.
Searches for routes and destination addresses of data packets for forwarding.
Forwards data packets.

Table 7-377 Functions of the LE1D2S04SEC0

Function	Description
Basic function	Provides four 10G Ethernet optical ports, sixteen 100/1000M Ethernet optical ports, and eight 10/100/1000M combo ports for data transmission and switching.
Distributed forwarding	Performs concurrent data forwarding using a distributed data plane.
Software feature	Switching between LAN and WAN ports
Hot swapping	Supported

Indicators and Ports

Figure 7-182 Indicators on the LE1D2S04SEC0 panel

Table 7-378 Indicators on the LE1D2S04SEC0 panel

Number	Indicator	Color	Description
1	ACT indicator of a 10GE optical port	Yellow	Blinking: The port is transmitting and receiving data.
2	LINK indicator of a 10GE optical port	Green	Steady on: A link has been established on the port.
3	ACT indicator of a lower GE optical port	Yellow	Blinking: The port is transmitting and receiving data.
4	ACT indicator of an upper GE optical port	Yellow	Blinking: The port is transmitting and receiving data.
5	LINK indicator of a lower GE optical port	Green	Steady on: A link has been established on the port.
6	Link indicator of an upper GE optical port	Green	Steady on: A link has been established on the port.
7	LINK/ACT indicator of an upper electrical port	Green	Steady on: A link has been established on the port. Blinking: The port is transmitting and receiving data.
8	LINK/ACT indicator of a lower electrical port	Green
9	RUN/ALM: running status indicator	Green	Steady on: The card is powered on. If the indicator is steady green for no more than 30 seconds, the CPU is being started. If the indicator is steady green for more than 30 seconds, the software is not running. Slow blinking: The card software is running properly. Fast blinking: The card software is starting.
		Red	Steady on: The card has failed and the fault requires manual intervention.
		Yellow	Steady on: The card is powered off. (For example, the card has been forcibly powered off using the power off command or is about to start.)

Figure 7-183 Ports on the LE1D2S04SEC0 panel

1	Four 10GBASE SFP+ ports
2	Sixteen 100/1000BASE-X ports
3	Eight combo ports, each of which consists of a 10/100/1000BASE-T port and a 100/1000BASE-X port

10GBASE SFP+ port

Table 7-379 describes the attributes of a 10GBASE SFP+ port.

Table 7-379 Attributes of a 10GBASE SFP+ port

Attribute	Description
Connector type	SFP+
Optical attributes	Depend on the SFP+ to SFP+ high-speed cable (1 m, 3 m, 5 m, 10 m), QSFP+ to 4*SFP+ high-speed cable (1 m, 3 m, 5 m), SFP+ optical module, or SFP+ optical cable used. For the optical modules supported by the LE1D2S04SEC0 and their attributes, see 10GE SFP+ Optical Modules, 10GE-CWDM SFP+ Optical Modules and 10GE-DWDM SFP+ Optical Modules.
Standards compliance	IEEE 802.3ae
Frame format	Ethernet_II, Ethernet_SAP, Ethernet_SNAP
Network protocol	IP

100/1000BASE-X port

Table 7-380 lists the attributes of a 100/1000BASE-X optical port with an optical module installed.

Table 7-380 Optical port attributes (optical module)

Attribute	Description
Connector type	SFP
Optical attributes	Depend on the SFP optical module used. For optical modules supported by the LE1D2S04SEC0 and their attributes, see FE SFP/eSFP Optical Modules, GE eSFP Optical Modules, GE-CWDM eSFP Optical Modules, and GE-DWDM eSFP Optical Modules.
Standards compliance	IEEE 802.3z
Frame format	Ethernet_II, Ethernet_SAP, Ethernet_SNAP
Network protocol	IP

Table 7-381 lists the attributes of a 100/1000BASE-X optical port with a copper module installed.

Table 7-381 Optical port attributes (copper module)

Attribute	Description
Connector type	SFP
Optical port attributes	Depend on the SFP copper module used. For details on the copper modules supported by the cards and attributes of the copper modules, see GE SFP Copper Modules (10 Mbit/s, 100 Mbit/s and 1000 Mbit/s rates).
Standards compliance	IEEE 802.3ab
Frame format	Ethernet_II, Ethernet_SAP, Ethernet_SNAP
Network protocol	IP

Combo port

A combo port is a dual-purpose port consisting of an Ethernet optical port and an Ethernet electrical port. The electrical and optical ports are multiplexed, and only one of them can work at a time.

A combo port supports three working modes: auto, fiber, and copper. You can configure a combo port to work in any mode using the combo-port command. By default, a combo works in auto mode, and the working port is determined in the following way:

If only an Ethernet cable is connected to the combo port, the electrical port will become the working port after the combo port goes Up.
If an optical module is installed on a combo port, the optical port will become the working port after the combo port goes Up, regardless of whether an Ethernet cable is connected to the electrical port.

Table 7-382 describes the attributes of a 10/100/1000BASE-T port.

Table 7-382 Attributes of a 10/100/1000BASE-T port

Attribute	Description
Connector type	RJ45
Standards compliance	IEEE 802.3ab
Frame format	Ethernet_II, Ethernet_SAP, Ethernet_SNAP
Network protocol	IP

Table 7-383 describes the attributes of a 100/1000BASE-X port.

Table 7-383 Attributes of a 100/1000BASE-X port

Attribute	Description
Connector type	SFP
Optical attributes	Depend on the SFP optical module used. For optical modules supported by the LE1D2S04SEC0 and their attributes, see FE SFP/eSFP Optical Modules, GE eSFP Optical Modules, GE-CWDM eSFP Optical Modules, and GE-DWDM eSFP Optical Modules.
Standards compliance	IEEE 802.3z
Frame format	Ethernet_II, Ethernet_SAP, Ethernet_SNAP
Network protocol	IP

Specifications

Table 7-384 Specifications of the LE1D2S04SEC0

Item	Description
Physical specifications	Dimensions (H x W x D): 35.1 mm x 397.2 mm x 430.4 mm (1.38 in. x 15.64 in. x 16.95 in.) Weight: 2.88 kg (6.35 lb) Maximum power consumption: 130 W

Item

Description

Physical specifications

Dimensions (H x W x D): 35.1 mm x 397.2 mm x 430.4 mm (1.38 in. x 15.64 in. x 16.95 in.)

Weight: 2.88 kg (6.35 lb)
Maximum power consumption: 130 W

Ordering Information

Card ordering information is subject to updates with product version upgrades. The ordering information provided in this manual is for reference only. To obtain the latest ordering information, contact Huawei switch distributors or Huawei local office.

Table 7-385 Ordering information

Part Number	Card Name	Card Model
03031VXS	4-port 10GBASE-X and 24-port 100/1000BASE-X and 8-port 10/100/1000BASE-T combo interface card (EC, RJ45/SFP/SFP+)	LE1D2S04SEC0

Version Mapping
Introduction
Functions
Indicators and Ports
Specifications
Ordering Information

Translation

简体中文

Download

Updated: 2022-05-19

Document ID: EDOC1000138177

Downloads: 469

Average rating:

This Document Applies to these Products

Related Version

Digital Signature File

Digital Signature Authentication Mode