LST3C04HX6E0 (03033FBP/03033FBP-001/03033FBP-002: 4-Port 100GE QSFP28 Interface Card (X6E, QSFP28))

S9300X Series Switches Hardware Description

Rate and give feedback:

Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).

Version Mapping

Table 7-920 Switch chassis and software versions matching the card

Card Name	Part Number	S9300X Chassis
LST3C04HX6E0	03033FBP	S9310X chassis: not supported S9300X-4, S9300X-8, and S9300X-12 chassis: supported in V200R019C00 and later versions NOTE: As for cards manufactured since June 2021: If they are used in V200R019C00, load V200R019SPH029 or a later patch, and load S9300X_V200R019C00SPC500_BOARD_MOD002.mod or a later mod file.
03033FBP-001	S9310X chassis: not supported S9300X-4, S9300X-8, and S9300X-12 chassis: supported in V200R021C10SPC500 and later versions NOTE: If the card is used in V200R019C10SPC500, install V200R019SPH058 or a later patch and S9300X_V200R019C10SPC500_BOARD_MOD003.mod or a later mod file. If the card is used in V200R021C00SPC100 or V200R021C01, install V200R021SPH011 or a later patch.
03033FBP-002	S9310X chassis: not supported S9300X-4, S9300X-8, and S9300X-12 chassis: supported in V200R021C10SPC600 and later versions NOTE: If the card is used in V200R019C10SPC500, install V200R019SPH380 or a later patch and S9300X_V200R019C10SPC500_BOARD_MOD005.mod or a later mod file. If the card is used in V200R021C00SPC100 or V200R021C01, install V200R021SPH180 or a later patch.

Card Name

Part Number

S9300X Chassis

LST3C04HX6E0

03033FBP

S9310X chassis: not supported

S9300X-4, S9300X-8, and S9300X-12 chassis: supported in V200R019C00 and later versions

NOTE:

As for cards manufactured since June 2021:

If they are used in V200R019C00, load V200R019SPH029 or a later patch, and load S9300X_V200R019C00SPC500_BOARD_MOD002.mod or a later mod file.

03033FBP-001

S9310X chassis: not supported

S9300X-4, S9300X-8, and S9300X-12 chassis: supported in V200R021C10SPC500 and later versions

NOTE:

If the card is used in V200R019C10SPC500, install V200R019SPH058 or a later patch and S9300X_V200R019C10SPC500_BOARD_MOD003.mod or a later mod file.
If the card is used in V200R021C00SPC100 or V200R021C01, install V200R021SPH011 or a later patch.

03033FBP-002

S9310X chassis: not supported

S9300X-4, S9300X-8, and S9300X-12 chassis: supported in V200R021C10SPC600 and later versions

NOTE:

If the card is used in V200R019C10SPC500, install V200R019SPH380 or a later patch and S9300X_V200R019C10SPC500_BOARD_MOD005.mod or a later mod file.
If the card is used in V200R021C00SPC100 or V200R021C01, install V200R021SPH180 or a later patch.

Introduction

The LST3C04HX6E0 can be installed in:

Slots 01 to 04 in an S9300X-4 chassis.
Slots 01 to 08 in an S9300X-8 chassis.
Slots 01 to 12 in an S9300X-12 chassis.

Figure 7-423 Appearance of the LST3C04HX6E0

Functions

Table 7-921 Functions of the LST3C04HX6E0

Function	Description
Basic function	Provides four 100GE optical ports for data transmission and switching.
Distributed forwarding	Performs concurrent data forwarding using a distributed data plane.
Hot swapping	Supported

Indicators and Ports

Figure 7-424 Indicators on the LST3C04HX6E0 panel

Table 7-922 Indicators on the LST3C04HX6E0 panel

Number	Indicator	Color	Description
1	ACT/LINK	Green	Steady on: A link has been established on the port. Blinking: The port is transmitting and receiving data.
2	RUN/ALM: running status indicator	Green	Steady on: The card is powered on. If the indicator is steady green for no more than 30 seconds, the CPU is being started. If the indicator is steady green for more than 30 seconds, the software is not running. Slow blinking: The card software is running properly. Fast blinking: The card software is starting.
		Red	Steady on: The card has failed and the fault requires manual intervention.
		Yellow	Steady on: The card is powered off. (For example, the card has been forcibly powered off using the power off command or is about to start.)

Figure 7-425 Ports on the LST3C04HX6E0 panel

1	Four 100GE optical ports to transmit and receive service traffic at 40 Gbit/s or 100 Gbit/s

100GE optical port

Table 7-923 lists the attributes of a 100GE optical port.

Table 7-923 Attributes of a 100GE optical port

Attribute	Description
Connector type	QSFP28
Optical port attributes	Depend on the QSFP28 - QSFP28 high-speed cable (1 m, 3 m), 40GE QSFP+ Optical Modules, 100GE QSFP28 Optical Modules or QSFP+ or QSFP28 AOC cable used.
Applicable cable	QSFP+ optical module and LC optical fiber QSFP+ optical module and MPO optical fiber (MPO-MPO or MPO-4DLC optical fiber) QSFP+ AOC cable (QSFP+ to QSFP+ or QSFP+ to 4SFP+) QSFP28 optical module and LC optical fiber QSFP28 optical module and MPO optical fiber (MPO-MPO or MPO-4*DLC optical fiber) QSFP28 high-speed copper cable (1 m or 3 m, can only be used as a CSS cable) QSFP28 AOC cable

Attribute

Description

Connector type

QSFP28

Optical port attributes

Depend on the QSFP28 - QSFP28 high-speed cable (1 m, 3 m), 40GE QSFP+ Optical Modules, 100GE QSFP28 Optical Modules or QSFP+ or QSFP28 AOC cable used.

Applicable cable

QSFP+ optical module and LC optical fiber

QSFP+ optical module and MPO optical fiber (MPO-MPO or MPO-4*DLC optical fiber)

QSFP+ AOC cable (QSFP+ to QSFP+ or QSFP+ to 4*SFP+)

QSFP28 optical module and LC optical fiber

QSFP28 optical module and MPO optical fiber (MPO-MPO or MPO-4*DLC optical fiber)

QSFP28 high-speed copper cable (1 m or 3 m, can only be used as a CSS cable)

QSFP28 AOC cable

Specifications

Table 7-924 Specifications of the LST3C04HX6E0

Item	Description
Physical specifications	Dimensions (H x W x D): 35.1 mm x 397.2 mm x 430.4 mm (1.38 in. x 15.64 in. x 16.95 in.) Weight: 3.5 kg (7.71 lb) Maximum power consumption: 177 W

Item

Description

Physical specifications

Dimensions (H x W x D): 35.1 mm x 397.2 mm x 430.4 mm (1.38 in. x 15.64 in. x 16.95 in.)

Weight: 3.5 kg (7.71 lb)
Maximum power consumption: 177 W

Ordering Information

Card ordering information is subject to updates with product version upgrades. The ordering information provided in this manual is for reference only. To obtain the latest ordering information, contact Huawei switch distributors or Huawei local office.

Table 7-925 Ordering information

Part Number	Card Description	Card Model
03033FBP 03033FBP-001 03033FBP-002	4-Port 100GE QSFP28 Interface Card (X6E, QSFP28)	LST3C04HX6E0

Translation

简体中文

Download

Updated: 2023-10-23

Document ID: EDOC1000138177

Downloads: 672

Average rating:

This Document Applies to these Products

Related Version

Digital Signature File

Digital Signature Authentication Mode

Enterprise

Huawei Cloud

Carrier

Consumer

Corporate

Version Mapping

Introduction

Functions

Indicators and Ports

Specifications

Ordering Information

Related Version

Related Documents

Digital Signature File