LE1D2G48SX1C-48-Port 100/1000BASE-X Interface Card (X1C, SFP)

S9300X Series Switches Hardware Description

Rate and give feedback:

Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).

Version Mapping

Table 7-272 Switch chassis and software versions matching the card

Card Name	S9300X Chassis
LE1D2G48SX1C	S9310X chassis: supported in V200R011C10 and later versions S9300X-4, S9300X-8, and S9300X-12 chassis: not supported

Card Name

S9300X Chassis

LE1D2G48SX1C

S9310X chassis: supported in V200R011C10 and later versions

S9300X-4, S9300X-8, and S9300X-12 chassis: not supported

Introduction

The LE1D2G48SX1C provides high performance, large entry sizes, and a large buffer for data switching. This card is highly integrated and has a large port density.

The LE1D2G48SX1C can be installed in:

Slots 01 to 10 in an S9310X chassis.

Figure 7-136 Appearance of the LE1D2G48SX1C

Functions

The LE1D2G48SX1C provides the following functions:

Communicates with the MPU and works under the control of the MPU.
Searches for routes and destination addresses of data packets for forwarding.
Forwards data packets.

Table 7-273 Functions of the LE1D2G48SX1C

Function	Description
Basic functions	Provides forty-eight GE optical ports for data access and switching.
Distributed forwarding	Performs concurrent data forwarding using a distributed data plane.
Hot swapping	The LE1D2G48SX1C is hot swappable.

Indicators and Ports

Figure 7-137 Indicators on the LE1D2G48SX1C panel

Table 7-274 Indicators on the LE1D2G48SX1C panel

Number	Indicator	Color	Description
1	ACT indicator of a lower optical port	Yellow	Blinking: The port is transmitting and receiving data.
2	ACT indicator of an upper optical port	Yellow	Blinking: The port is transmitting and receiving data.
3	LINK indicator of a lower optical port	Green	Steady on: A link has been established on the port.
4	LINK indicator of an upper optical port	Green	Steady on: A link has been established on the port.
5	RUN/ALM: running status indicator	Green	Steady on: The card is powered on. If the indicator is steady green for no more than 30 seconds, the CPU is being started. If the indicator is steady green for more than 30 seconds, the software is not running. Slow blinking: The card software is running properly. Fast blinking: The card software is starting.
		Red	Steady on: The card has failed and the fault requires manual intervention.
		Yellow	Steady on: The card is powered off. (For example, the card has been forcibly powered off using the power off command or is about to start.)

Figure 7-138 Ports on the LE1D2G48SX1C panel

1	Forty-eight 100/1000BASE-X ports

100/1000BASE-X port

Table 7-275 describes the attributes of a 100/1000BASE-X port with an optical module installed.

Table 7-275 Optical port attributes (optical module)

Attribute	Description
Connector type	SFP
Optical port attributes	Depend on the SFP optical module used. For optical modules supported by the LE1D2G48SX1C and their attributes, see FE SFP/eSFP Optical Modules, GE eSFP Optical Modules, GE-CWDM eSFP Optical Modules, and GE-DWDM eSFP Optical Modules.
Standards compliance	IEEE 802.3z
Frame format	Ethernet_II, Ethernet_SAP, Ethernet_SNAP
Network protocol	IP

Table 7-276 describes the attributes of a 100/1000BASE-X port with a copper module installed.

Table 7-276 Optical port attributes (copper module)

Attribute	Description
Connector type	SFP
Optical port attributes	Depend on the SFP copper module used. For details on the copper modules supported by the cards and attributes of the copper modules, see GE SFP Copper Modules (10 Mbit/s, 100 Mbit/s and 1000 Mbit/s rates).
Standards compliance	IEEE 802.3ab
Frame format	Ethernet_II, Ethernet_SAP, Ethernet_SNAP
Network protocol	IP

Specifications

Table 7-277 Specifications of the LE1D2G48SX1C

Item	Description
Physical specifications	Dimensions (H x W x D): 35.1 mm x 397.2 mm x 430.4 mm (1.38 in. x 15.64 in. x 16.95 in.) Weight: 3.04 kg (6.70 lb) Maximum power consumption: 140 W

Item

Description

Physical specifications

Dimensions (H x W x D): 35.1 mm x 397.2 mm x 430.4 mm (1.38 in. x 15.64 in. x 16.95 in.)

Weight: 3.04 kg (6.70 lb)
Maximum power consumption: 140 W

Ordering Information

Card ordering information is subject to updates with product version upgrades. The ordering information provided in this manual is for reference only. To obtain the latest ordering information, contact Huawei switch distributors or Huawei local office.

Table 7-278 Ordering information

Part Number	Card Name	Card Model
03032MFK	48-port 100/1000BASE-X interface card (X1C, SFP)	LE1D2G48SX1C

Version Mapping
Introduction
Functions
Indicators and Ports
Specifications
Ordering Information

Translation

简体中文

Download

Updated: 2022-05-19

Document ID: EDOC1000138177

Downloads: 469

Average rating:

This Document Applies to these Products

Related Version

Digital Signature File

Digital Signature Authentication Mode