LST3Y40SX6H0 (03033LCV: 40-Port 25GE SFP28 Interface Card (X6H, SFP28))

S9300X Series Switches Hardware Description

Rate and give feedback:

Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).

Version Mapping

Table 7-791 Switch chassis and software versions matching the card

Card Name	Part Number	S9300X Chassis
LST3Y40SX6H0	03033LCV	S9310X chassis: not supported S9300X-4, S9300X-8, and S9300X-12 chassis: supported in V200R019C10 and later versions

Card Name

Part Number

S9300X Chassis

LST3Y40SX6H0

03033LCV

S9310X chassis: not supported

S9300X-4, S9300X-8, and S9300X-12 chassis: supported in V200R019C10 and later versions

Introduction

The LST3Y40SX6H0 can be installed in:

Slots 01 to 04 in an S9300X-4 chassis.
Slots 01 to 08 in an S9300X-8 chassis.
Slots 01 to 12 in an S9300X-12 chassis.

Figure 7-359 Appearance of the LST3Y40SX6H0

Functions

Table 7-792 Functions of the LST3Y40SX6H0

Function	Description
Basic function	Provides forty 25GE optical ports for data access and switching by default. You can run the set device port-config-mode 10g-port enable command to change these ports to thirty-two 25GE optical ports and sixteen 10GE optical ports. V200R023C00 and later versions, you can run the set device port-config-mode all-10g-port enable command to change these ports to forty-eight 10GE optical ports.
Distributed forwarding	Performs concurrent data forwarding using a distributed data plane.
Hot swapping	Supported

Indicators and Ports

Figure 7-360 Indicators on the LST3Y40SX6H0 panel

Table 7-793 Indicators on the LST3Y40SX6H0 panel

Number	Indicator	Color	Description
1	ACT indicator of a lower optical port	Yellow	Blinking: The port is transmitting and receiving data.
2	ACT indicator of an upper optical port	Yellow	Blinking: The port is transmitting and receiving data.
3	LINK indicator of a lower optical port	Green	Steady on: A link has been established on the port.
4	LINK indicator of an upper optical port	Green	Steady on: A link has been established on the port.
5	RUN/ALM: running status indicator	Green	Steady on: The card is powered on. If the indicator is steady green for no more than 30 seconds, the CPU is being started. If the indicator is steady green for more than 30 seconds, the software is not running. Slow blinking: The card software is running properly. Fast blinking: The card software is starting.
		Red	Steady on: The card has failed and the fault requires manual intervention.
		Yellow	Steady on: The card is powered off. (For example, the card has been forcibly powered off using the power off command or is about to start.)

Figure 7-361 Ports on the panel of an LST3Y40SX6H0 (default mode)

1	Forty 25GE optical ports, used for transmitting and receiving service data at 25 Gbit/s, 10 Gbit/s, or 1 Gbit/s

Figure 7-362 Ports on the panel of an LST3Y40SX6H0 (with the port mode changed)

1	Thirty-two 25GE optical ports, used for transmitting and receiving service data at 25 Gbit/s, 10 Gbit/s, or 1 Gbit/s
2	Sixteen 10GE optical ports, used for transmitting and receiving service data at 10 Gbit/s or 1 Gbit/s

By default, the first 40 ports are 25GE optical ports and the last eight ports are unavailable.
After the set device port-config-mode 10g-port enable command is run to change the port mode, the first 32 ports are 25GE optical ports and the last 16 ports are 10GE optical ports. V200R023C00 and later versions, you can run the set device port-config-mode all-10g-port enable command to change these ports to forty-eight 10GE optical ports.
When a 25GE optical module or cable is connected to a 25GE optical port, the port can automatically adjust its rate to 25 Gbit/s.
When a 10GE optical module or cable is connected to a 25GE optical port, the port can automatically adjust its rate to 10 Gbit/s.
Before installing a GE optical module or copper module on a 25GE optical port, run the port mode ge command to configure the port to work at 1 Gbit/s.

25GE optical port

Table 7-794 Optical port attributes (25GE optical module, SFP28 high-speed cable or SFP28 optical cable)

Attribute

Description

Connector type

SFP28

Optical port attributes

Depend on the 25GE SFP28 Optical Modules, SFP28 High-Speed Cable or SFP28 Optical Cable used.

Applicable cable

SFP28 optical module and LC optical fiber

SFP28 high-speed copper cable

SFP28 AOC cable

Table 7-795 Optical port attributes (GE optical module)

Attribute	Description
Connector type	SFP28
Optical port attributes	Depend on the SFP optical module used. For the SFP optical modules supported by the LST3Y40SX6H0 and their attributes, see GE eSFP Optical Modules, GE-CWDM eSFP Optical Modules, and GE-DWDM eSFP Optical Modules.
Applicable cable	SFP/eSFP optical module and LC optical fiber

Table 7-796 Optical port attributes (10GE optical module, SFP+ high-speed cable or SFP+ optical cable)

Attribute

Description

Connector type

SFP28

Optical port attributes

Depend on the SFP+ to SFP+ high-speed cable (1 m, 3 m, 5 m, 10 m), QSFP+ to 4*SFP+ high-speed cable (1 m, 3 m, 5 m), SFP+ optical module, or SFP+ optical cable used.

For the optical modules supported by the LST3Y40SX6H0 and their attributes, see 10GE SFP+ Optical Modules (OSXD22N00 not supported), 10GE-CWDM SFP+ Optical Modules and 10GE-DWDM SFP+ Optical Modules.

Applicable cable

SFP+ optical module and LC optical fiber

SFP+ high-speed copper cable

SFP+ AOC cable

Table 7-797 Optical port attributes (copper module)

Attribute

Description

Connector type

SFP28

Optical port attributes

Depend on the SFP copper module used.

For details on the copper modules supported by the cards and attributes of the copper modules, see GE SFP Copper Modules (100 Mbit/s and 1000 Mbit/s rates).

Applicable cable

SFP copper module and Ethernet cable

10GE optical port

Table 7-798 Optical port attributes (GE optical module)

Attribute	Description
Connector type	SFP+
Optical port attributes	Depend on the SFP optical module used. For the SFP optical modules supported by the LST3Y40SX6H0 and their attributes, see GE eSFP Optical Modules, GE-CWDM eSFP Optical Modules, and GE-DWDM eSFP Optical Modules.
Applicable cable	GE eSFP optical module and LC optical fiber

Table 7-799 Optical port attributes (10GE optical module, SFP+ high-speed cable or SFP+ optical cable)

Attribute

Description

Connector type

SFP+

Optical port attributes

Depend on the SFP+ to SFP+ high-speed cable (1 m, 3 m, 5 m, 10 m), QSFP+ to 4*SFP+ high-speed cable (1 m, 3 m, 5 m), SFP+ optical module, or SFP+ optical cable used.

For the optical modules supported by the LST3Y40SX6H0 and their attributes, see 10GE SFP+ Optical Modules (OSXD22N00 not supported), 10GE-CWDM SFP+ Optical Modules and 10GE-DWDM SFP+ Optical Modules.

Applicable cable

SFP+ optical module and LC optical fiber

SFP+ high-speed copper cable

SFP+ AOC cable

Table 7-800 Optical port attributes (copper module)

Attribute

Description

Connector type

SFP+

Optical port attributes

Depend on the SFP copper module used.

For details on the copper modules supported by the cards and attributes of the copper modules, see GE SFP Copper Modules (100 Mbit/s and 1000 Mbit/s rates).

Applicable cable

SFP copper module and Ethernet cable

Specifications

Table 7-801 Specifications of the LST3Y40SX6H0

Item	Description
Physical specifications	Dimensions (H x W x D): 35.1 mm x 397.2 mm x 430.4 mm (1.38 in. x 15.64 in. x 16.95 in.) Weight: 4.25 kg (9.37 lb) Maximum power consumption: 341 W

Item

Description

Physical specifications

Dimensions (H x W x D): 35.1 mm x 397.2 mm x 430.4 mm (1.38 in. x 15.64 in. x 16.95 in.)

Weight: 4.25 kg (9.37 lb)
Maximum power consumption: 341 W

Ordering Information

Card ordering information is subject to updates with product version upgrades. The ordering information provided in this manual is for reference only. To obtain the latest ordering information, contact Huawei switch distributors or Huawei local office.

Table 7-802 Ordering information

Part Number	Card Description	Card Model
03033LCV	40-Port 25GE SFP28 Interface Card (X6H, SFP28)	LST3Y40SX6H0

Translation

简体中文

Download

Updated: 2023-10-23

Document ID: EDOC1000138177

Downloads: 671

Average rating:

This Document Applies to these Products

Related Version

Digital Signature File

Digital Signature Authentication Mode

Enterprise

Huawei Cloud

Carrier

Consumer

Corporate

Version Mapping

Introduction

Functions

Indicators and Ports

Specifications

Ordering Information

Related Version

Related Documents

Digital Signature File