LE0DG48VEA00-48-Port 10/100/1000BASE-T PoE Interface Card (EA, RJ45, POE)

S9300X Series Switches Hardware Description

Rate and give feedback:

Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).

Version Mapping

Table 7-141 Switch chassis and software versions matching the card

Card Name	S9300X Chassis
LE0DG48VEA00	S9310X chassis: supported in V200R010C00 and later versions S9300X-4, S9300X-8, and S9300X-12 chassis: not supported

Card Name

S9300X Chassis

LE0DG48VEA00

S9310X chassis: supported in V200R010C00 and later versions

S9300X-4, S9300X-8, and S9300X-12 chassis: not supported

Introduction

The LE0DG48VEA00 can be installed in:

Slots 01 to 10 in an S9310X chassis.

Figure 7-69 Appearance of the LE0DG48VEA00

Functions

Table 7-142 Functions of the LE0DG48VEA00

Function	Description
Basic function	The LE0DG48VEA00 has two units: Data switching unit: consists of the CPU, switching chip, and physical layer (PHY). PoE management unit: consists of the CPU and the Dual Inline Memory Module (DIMM). The LE0DG48VEA00 provides: Forty-eight GE electrical ports for data transmission and switching
Distributed forwarding	Performs concurrent data forwarding using a distributed data plane.
Hot swapping	The LE0DG48VEA00 is hot swappable.

Function

Description

Basic function

The LE0DG48VEA00 has two units:

Data switching unit: consists of the CPU, switching chip, and physical layer (PHY).
PoE management unit: consists of the CPU and the Dual Inline Memory Module (DIMM).

The LE0DG48VEA00 provides:

Forty-eight GE electrical ports for data transmission and switching

Distributed forwarding

Performs concurrent data forwarding using a distributed data plane.

Hot swapping

The LE0DG48VEA00 is hot swappable.

Usage Constraints

When the is registered on a non-PoE chassis (such as the S7703, S7706, or S7712), the DIMM cannot be installed, the power modules in the power slots can work properly, the PoE power modules in the PoE slots cannot work properly, the data transmission function is available, and the PoE function is not available.
When the is registered on a PoE chassis (such as the S7706, S7712, S7703 PoE, or S7706 PoE), ensure that a DIMM has been installed in the DIMM slot on the board, the power modules in the power slots and the PoE power modules in the PoE slots can work properly, and the data transmission and PoE functions are available.
To use an LE0DG48VEA00 card in an S9310X chassis, do not install a DIMM module in the card. When used in an S9310X chassis, the LE0DG48VEA00 card does not provide the PoE function.

Indicators and Ports

Figure 7-70 Indicators on the LE0DG48VEA00 panel

Table 7-143 Indicators on the LE0DG48VEA00 panel

Number	Indicator	Color	Description
1	LINK/ACT indicator of an upper electrical port	Green	Steady on: A link has been established on the port. Blinking: The port is transmitting and receiving data.
2	LINK/ACT indicator of a lower electrical port	Green
3	RUN/ALM: running status indicator	Green	Steady on: The card is powered on. If the indicator is steady green for no more than 30 seconds, the CPU is being started. If the indicator is steady green for more than 30 seconds, the software is not running. Slow blinking: The card software is running properly. Fast blinking: The card software is starting.
		Red	Steady on: The card has failed and the fault requires manual intervention.
		Yellow	Steady on: The card is powered off. (For example, the card has been forcibly powered off using the power off command or is about to start.)

Figure 7-71 Ports on the LE0DG48VEA00 panel

1	Forty-eight 10/100/1000BASE-T electrical ports. The electrical ports support the PoE function and can provide DC power for the directly connected devices such as IP phones, wireless access points (APs), and network cameras.

10/100/1000BASE-T electrical ports

Table 7-144 lists the attributes of a 10/100/1000BASE-T electrical port.

Table 7-144 10/100/1000BASE-T electrical port attributes

Attribute	Description
Connector type	RJ45
Standards compliance	IEEE 802.3ab, IEEE 802.3af, IEEE 802.3at
Frame format	Ethernet_II, Ethernet_SAP, Ethernet_SNAP
Network protocol	IP

Specifications

Table 7-145 Specifications of the LE0DG48VEA00

Item	Description
Physical specifications	Dimensions (H x W x D): 35.1 mm x 397.2 mm x 430.4 mm (1.38 in. x 15.64 in. x 16.95 in.) Weight: 2.60 kg (5.73 lb) Maximum power consumption: 64 W (The PoE power supply is not included.)

Item

Description

Physical specifications

Dimensions (H x W x D): 35.1 mm x 397.2 mm x 430.4 mm (1.38 in. x 15.64 in. x 16.95 in.)

Weight: 2.60 kg (5.73 lb)
Maximum power consumption: 64 W (The PoE power supply is not included.)

Ordering Information

Card ordering information is subject to updates with product version upgrades. The ordering information provided in this manual is for reference only. To obtain the latest ordering information, contact Huawei switch distributors or Huawei local office.

Table 7-146 Ordering information

Part Number	Card Description	Card Model
03020RTY	48-port 10/100/1000BASE-T PoE interface card (EA, RJ45, PoE)	LE0DG48VEA00 NOTE: After the display elabel command is executed, the manufactured model of the card is displayed as LE02G48VA.

Version Mapping
Introduction
Functions
Usage Constraints
Indicators and Ports
Specifications
Ordering Information

Translation

简体中文

Download

Updated: 2022-05-19

Document ID: EDOC1000138177

Downloads: 469

Average rating:

This Document Applies to these Products

Related Version

Digital Signature File

Digital Signature Authentication Mode