LST3M24BX6E0 (03034DGU-001: 24-port 100M/1G/2.5G/5G/10G and 24-port 100M/1G interface card (X6E,RJ45))
Overview
| Item | Details |
|---|---|
| Description | 24-port 100M/1G/2.5G/5G/10G and 24-port 100M/1G interface card (X6E,RJ45) |
| Part Number | 03034DGU-001 |
| Model | LST3M24BX6E0 |
Appearance
Version Mapping
| Product | Product Model | First Supported Version | Limitations | IDs of available slots |
|---|---|---|---|---|
| S9300X | S9300X-12 | V200R021C10 | If this LPU is used in V200R021C00SPC100 or V200R021C01, V200R021SPH010 or a later patch needs to be loaded. | 01–12 |
| S9300X | S9300X-4 | V200R021C10 | If this LPU is used in V200R021C00SPC100 or V200R021C01, V200R021SPH010 or a later patch needs to be loaded. | 01–04 |
| S9300X | S9300X-8 | V200R021C10 | If this LPU is used in V200R021C00SPC100 or V200R021C01, V200R021SPH010 or a later patch needs to be loaded. | 01–08 |
Indicators
1. LINK/ACT indicator of an upper electrical port |
2. LINK/ACT indicator of a lower electrical port |
3. RUN/ALM: running status indicator |
| Silkscreen | Name | Color | Status | Description |
|---|---|---|---|---|
| - | LINK/ACT indicator of an upper electrical port | Green | Steady on | A link has been established on the port. |
| Green | Blinking | The port is transmitting and receiving data. | ||
| - | LINK/ACT indicator of a lower electrical port | Green | Steady on | A link has been established on the port. |
| Green | Blinking | The port is transmitting and receiving data. | ||
| RUN/ALM | Running status indicator | Green | Steady on | The card is powered on. If the indicator is steady green for no more than 30 seconds, the CPU is being started. If the indicator is steady green for more than 30 seconds, the software is not running. |
| Green | Slow blinking | The card software is running properly. | ||
| Green | Fast blinking | The card software is starting. | ||
| Red | Steady on | The card has failed and the fault requires manual intervention. | ||
| Yellow | Steady on | The card is powered off. (For example, the card has been forcibly powered off using the power off command or is about to start.) |
Ports
1. Twenty-four 100/1000BASE-T ports |
2. Twenty-four 100M/1000M/2.5GE/5GE/10GE BASE-T ports (multi-GE ports) |
Cable Type (6-a-1 Bundle) |
Multi-GE Port (Different Rates) |
|||
|---|---|---|---|---|
100M/1000M |
2.5GE |
5GE |
10GE |
|
Category 5e unshielded twisted pair (Cat5e UTP) |
100 m |
100 m |
Not recommended due to high risk |
Not supported |
Category 5e shielded twisted pair (Cat5e STP) |
100 m |
100 m |
100 m |
Not supported |
Category 6 unshielded twisted pair (Cat6 UTP) |
100 m |
100 m |
100 m Not recommended due to high risk |
Not supported |
Category 6 shielded twisted pair (Cat6 STP) |
100 m |
100 m |
100 m |
Not supported |
Category 6A unshielded twisted pair (Cat6A U/UTP) |
100 m |
100 m |
100 m Not recommended due to high risk |
Not supported |
Category 6A foiled/unshielded twisted pair (Cat6A F/UTP) |
100 m |
100 m |
100 m |
100 m |
Category 6A shielded twisted pair (Cat6A STP) |
100 m |
100 m |
100 m |
100 m |
Category 7 twisted pair (Cat7) |
100 m |
100 m |
100 m |
100 m |
6-a-1 stands for the six-around-one cable bundle mode, with one cable in the center and six cables bundled evenly around it.
- 802.3bz requires that the ALSNR value for alien crosstalk between Ethernet cables be greater than 0, but the standards for Cat5e and Cat6 unshielded twisted pairs do not specify the required ALSNR value. Therefore, such cables may not meet the crosstalk requirement in 802.3bz, causing severe problems such as continuous packet loss.
- According the cabling specification TIA TSB-5021, using Cat5e and Cat6 cables for 5G poses high risks.
- Currently, no clear onsite testing or evaluation method is available for checking whether ALSNR of cables conforms to 802.3bz.
If Cat5e and Cat6 unshielded twisted pairs do not meet the 5G requirement, you are advised to replace them with shielded twisted pairs or reduce the rate of ports to 2.5G.
| Port | Connector Type | Description | Available Components |
|---|---|---|---|
| 100M/1000M/2.5GE/5GE/10GE BASE-T electrical port (multi-GE port) | RJ45 | A 100M/1000M/2.5GE/5GE/10GE BASE-T electrical port sends and receives service data at 100 Mbit/s, 1 Gbit/s, 2.5 Gbit/s, 5 Gbit/s, or 10 Gbit/s. | If the 2.5 Gbit/s or 5 Gbit/s speed is required, the port must use an Ethernet cable of Cat5e or higher category. If the 10 Gbit/s speed is required, the port must use an Ethernet cable of Cat6A F/UTP or higher category. |
| 100/1000BASE-T electrical port | RJ45 | A 100/1000BASE-T electrical port sends and receives service data at 100/1000 Mbit/s. |
Functions and Features
| Functions and Features | Description |
|---|---|
| Basic function | The card provides twenty-four 100M/1000M/2.5GE/5GE/10GE BASE-T ports and twenty-four 100/1000BASE-T ports for data transmission and switching. |
| Distributed forwarding | Performs concurrent data forwarding using a distributed data plane. |
| Hot swapping | Supported |
Technical Specifications
| Item | Specification |
|---|---|
| Dimensions without packaging (H x W x D) [mm(in.)] | 35.1 mm x 397.2 mm x 430.4 mm (1.38 in. x 15.64 in. x 16.95 in.) |
| Dimensions with packaging (H x W x D) [mm(in.)] | 160 mm x 510 mm x 570 mm (6.3 in. x 20.1 in. x 22.44 in.) |
| Weight without packaging [kg(lb)] | 3.70 kg (8.16 lb) |
| Weight with packaging [kg(lb)] | 5.75 kg (12.68 lb) |
| Typical power consumption [W] | 168 W |
| Typical heat dissipation [BTU/hour] | 573.23 BTU/hour |
| Maximum power consumption [W] | 192 W |
| Maximum heat dissipation [BTU/hour] | 655.12 BTU/hour |
| Memory | 1 GB |
