LE1D2X12SSC0-12-Port 10GBASE-X Interface Card (SC, SFP+)

S9300X Series Switches Hardware Description

Rate and give feedback:

Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).

Version Mapping

Table 7-624 Switch chassis and software versions matching the card

Card Name	S9300X Chassis
LE1D2X12SSC0	S9310X chassis: supported in V200R010C00 and later versions S9300X-4, S9300X-8, and S9300X-12 chassis: not supported

Card Name

S9300X Chassis

LE1D2X12SSC0

S9310X chassis: supported in V200R010C00 and later versions

S9300X-4, S9300X-8, and S9300X-12 chassis: not supported

Introduction

The LE1D2X12SSC0 can be installed in:

Slots 01 to 10 in an S9310X chassis.

Figure 7-280 Appearance of the LE1D2X12SSC0

Functions

Table 7-625 Functions of the LE1D2X12SSC0

Function	Description
Basic function	Provides twelve 10GE optical ports for data transmission and switching.
Distributed forwarding	Performs concurrent data forwarding using a distributed data plane.
Hot swapping	Supported

Indicators and Ports

Figure 7-281 Indicators on the LE1D2X12SSC0 panel

Table 7-626 Indicators on the LE1D2X12SSC0 panel

Number	Indicator	Color	Description
1	ACT indicator of a lower optical port	Yellow	Blinking: The port is transmitting and receiving data.
2	ACT indicator of an upper optical port	Yellow	Blinking: The port is transmitting and receiving data.
3	LINK indicator of a lower optical port	Green	Steady on: A link has been established on the port.
4	LINK indicator of an upper optical port	Green	Steady on: A link has been established on the port.
5	RUN/ALM: running status indicator	Green	Steady on: The card is powered on. If the indicator is steady green for no more than 30 seconds, the CPU is being started. If the indicator is steady green for more than 30 seconds, the software is not running. Slow blinking: The card software is running properly. Fast blinking: The card software is starting.
		Red	Steady on: The card has failed and the fault requires manual intervention.
		Yellow	Steady on: The card is powered off. (For example, the card has been forcibly powered off using the power off command or is about to start.)

Figure 7-282 Ports on the LE1D2X12SSC0 panel

1	Twelve 10GBASE SFP+/1000BASE-X ports

10GBASE SFP+/1000BASE-X port

10GBASE SFP+/1000BASE-X ports support 10GE and GE auto sensing. Table 7-627 describes the attributes of a port working in 1000M mode, and Table 7-628 describes the attributes of a port working in 10G mode. Table 7-629 describes the attributes of a 10GBASE SFP+/1000BASE-X port with a copper module installed.

Table 7-627 Optical port attributes (GE optical module)

Attribute	Description
Connector type	SFP+
Optical attributes	Depend on the SFP optical module used. For the optical modules supported by the LE1D2X12SSC0 and their attributes, see GE eSFP Optical Modules, GE-CWDM eSFP Optical Modules, and GE-DWDM eSFP Optical Modules.
Standards compliance	IEEE802.3z
Frame format	Ethernet_II, Ethernet_SAP, Ethernet_SNAP
Network protocol	IP

Table 7-628 Optical port attributes (10GE optical module, high-speed copper cable, or SFP+ optical cable)

Attribute	Description
Connector type	SFP+
Optical attributes	Depend on the SFP+ to SFP+ high-speed cable (1 m, 3 m, 5 m, 10 m), QSFP+ to 4*SFP+ high-speed cable (1 m, 3 m, 5 m), SFP+ optical module, or SFP+ optical cable used. For the optical modules supported by the LE1D2X12SSC0 and their attributes, see 10GE SFP+ Optical Modules, 10GE-CWDM SFP+ Optical Modules and 10GE-DWDM SFP+ Optical Modules.
Standards compliance	IEEE 802.3ae
Frame format	Ethernet_II, Ethernet_SAP, Ethernet_SNAP
Network protocol	IP

Table 7-629 Optical port attributes (copper module)

Attribute	Description
Connector type	SFP
Optical port attributes	Depend on the SFP copper module used. For details on the copper modules supported by the cards and attributes of the copper modules, see GE SFP Copper Modules (1000 Mbit/s rates).
Standards compliance	IEEE 802.3ab
Frame format	Ethernet_II, Ethernet_SAP, Ethernet_SNAP
Network protocol	IP

Specifications

Table 7-630 Specifications of the LE1D2X12SSC0

Item	Description
Physical specifications	Dimensions (H x W x D): 35.1 mm x 397.2 mm x 430.4 mm (1.38 in. x 15.64 in. x 16.95 in.) Weight: 2.8 kg (6.17 lb) Maximum power consumption: 107.5 W

Item

Description

Physical specifications

Dimensions (H x W x D): 35.1 mm x 397.2 mm x 430.4 mm (1.38 in. x 15.64 in. x 16.95 in.)

Weight: 2.8 kg (6.17 lb)
Maximum power consumption: 107.5 W

Ordering Information

Card ordering information is subject to updates with product version upgrades. The ordering information provided in this manual is for reference only. To obtain the latest ordering information, contact Huawei switch distributors or Huawei local office.

Table 7-631 Ordering information

Part Number	Card Name	Card Model
03031VXQ	12-port 10GBASE-X interface card (SC, SFP+)	LE1D2X12SSC0

Version Mapping
Introduction
Functions
Indicators and Ports
Specifications
Ordering Information

Translation

简体中文

Download

Updated: 2022-05-19

Document ID: EDOC1000138177

Downloads: 468

Average rating:

This Document Applies to these Products

Related Version

Digital Signature File

Digital Signature Authentication Mode