LE0DS24XEA00-24-Port 100/1000BASE-X and 2-Port 10GBASE-X Interface Card (EA, SFP/XFP)

S9300X Series Switches Hardware Description

Rate and give feedback:

Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).

Version Mapping

Table 7-352 Switch chassis and software versions matching the card

Card Name	S9300X Chassis
LE0DS24XEA00	S9310X chassis: supported in V200R010C00 and later versions S9300X-4, S9300X-8, and S9300X-12 chassis: not supported

Card Name

S9300X Chassis

LE0DS24XEA00

S9310X chassis: supported in V200R010C00 and later versions

S9300X-4, S9300X-8, and S9300X-12 chassis: not supported

Introduction

The LE0DS24XEA00 can be installed in:

Slots 01 to 10 in an S9310X chassis.

Figure 7-172 Appearance of the LE0DS24XEA00

Functions

Table 7-353 Functions of the LE0DS24XEA00

Function	Description
Basic function	Provides twenty-four GE optical ports and two 10GE optical ports for data transmission and switching.
Distributed forwarding	Performs concurrent data forwarding using a distributed data plane.
Software feature	LAN/WAN interface switching
Hot swapping	The LE0DS24XEA00 is hot swappable.

Indicators and Ports

Figure 7-173 Indicators on the LE0DS24XEA00 panel

Table 7-354 Indicators on the LE0DS24XEA00 panel

Number	Indicator	Color	Description
1	ACT indicator	Yellow	Blinking: The port is transmitting and receiving data.
2	LINK indicator	Green	Steady on: A link has been established on the port.
3	ACT indicator of a lower optical port	Yellow	Blinking: The port is transmitting and receiving data.
4	ACT indicator of an upper optical port	Yellow	Blinking: The port is transmitting and receiving data.
5	LINK indicator of a lower optical port	Green	Steady on: A link has been established on the port.
6	LINK indicator of an upper optical port	Green	Steady on: A link has been established on the port.
7	RUN/ALM: running status indicator	Green	Steady on: The card is powered on. If the indicator is steady green for no more than 30 seconds, the CPU is being started. If the indicator is steady green for more than 30 seconds, the software is not running. Slow blinking: The card software is running properly. Fast blinking: The card software is starting.
		Red	Steady on: The card has failed and the fault requires manual intervention.
		Yellow	Steady on: The card is powered off. (For example, the card has been forcibly powered off using the power off command or is about to start.)

Figure 7-174 Ports on the LE0DS24XEA00 panel

1	Two 10GBASE XFP optical ports
2	Twenty-four 100/1000BASE-X optical ports

100/1000BASE-X optical port

Table 7-355 lists the attributes of a 100/1000BASE-X optical port with an optical module installed.

Table 7-355 100/1000BASE-X optical port attributes (GE optical module)

Attribute	Description
Connector type	SFP
Optical port attributes	Depend on the SFP optical module used. For details about the optical modules supported by the LE0DS24XEA00 and their attributes, see FE SFP/eSFP Optical Modules, GE eSFP Optical Modules, GE-CWDM eSFP Optical Modules, and GE-DWDM eSFP Optical Modules.
Standards compliance	IEEE802.3z
Frame format	Ethernet_II, Ethernet_SAP, Ethernet_SNAP
Network protocol	IP

Table 7-356 lists the attributes of a 100/1000BASE-X optical port with a copper module installed.

Table 7-356 Optical port attributes (copper module)

Attribute	Description
Connector type	SFP
Optical port attributes	Depend on the SFP copper module used. For details on the copper modules supported by the cards and attributes of the copper modules, see GE SFP Copper Modules (10 Mbit/s, 100 Mbit/s and 1000 Mbit/s rates).
Standards compliance	IEEE 802.3ab
Frame format	Ethernet_II, Ethernet_SAP, Ethernet_SNAP
Network protocol	IP

10GBASE XFP optical port

Table 7-357 lists the attributes of a 10GBASE XFP optical port.

Table 7-357 10GBASE XFP optical port attributes

Attribute	XFP Description
Connector type	XFP
Optical port attributes	Depend on the XFP optical module used. For details about the optical modules supported by the LE0DS24XEA00 and their attributes, see 10GE XFP Optical Modules, 10GE-CWDM XFP Optical Modules, and 10GE-DWDM XFP Optical Modules.
Standards compliance	IEEE 802.3ae
Frame format	Ethernet_II, Ethernet_SAP, Ethernet_SNAP
Network protocol	IP

Specifications

Table 7-358 Specifications of the LE0DS24XEA00

Item	Description
Physical specifications	Dimensions (H x W x D): 35.1 mm x 397.2 mm x 430.4 mm (1.38 in. x 15.64 in. x 16.95 in.) Weight: 2.40 kg (5.29 lb) Maximum power consumption: 65 W

Item

Description

Physical specifications

Dimensions (H x W x D): 35.1 mm x 397.2 mm x 430.4 mm (1.38 in. x 15.64 in. x 16.95 in.)

Weight: 2.40 kg (5.29 lb)
Maximum power consumption: 65 W

Ordering Information

Card ordering information is subject to updates with product version upgrades. The ordering information provided in this manual is for reference only. To obtain the latest ordering information, contact Huawei switch distributors or Huawei local office.

Table 7-359 Ordering information

Part Number	Card Description	Card Model
03020NNQ	24-port 100/1000BASE-X and 2-port 10GBASE-X interface card (EA, SFP/XFP)	LE0DS24XEA00 NOTE: After the display elabel command is executed, the manufactured model of the card is displayed as LE02S24XA.

Version Mapping
Introduction
Functions
Indicators and Ports
Specifications
Ordering Information

Translation

简体中文

Download

Updated: 2022-05-19

Document ID: EDOC1000138177

Downloads: 469

Average rating:

This Document Applies to these Products

Related Version

Digital Signature File

Digital Signature Authentication Mode