No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Command Reference

OceanStor 18000 V3 Series V300R006

This document is applicable to OceanStor 18500 V3 and 18800 V3. Based on the CLI provided by the DeviceManager, this document describes how to use variouscommands classified by functions and how to set the CLI and manage the storage system throughthese commands. The document that you browse online matches the latest C version of the product. Click Download to download documents of other C versions.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
change svp management_ip

change svp management_ip

Function

The change svp management_ip command is used to configure the IP address of a management port on SVP. Both IPv4 and IPv6 addresses can be configured, which is used by terminals to access the disk array.

Format

change svp management_ip eth_port_id=? ip_type=? [ ipv4_address=? mask=? [ gateway_ipv4=? ] ] [ ipv6_address=? prefix_length=? [ gateway_ipv6=? ] ] [ delete_gateway=? ]

Parameters

Parameter

Description

Value

eth_port_id=?

Indicates the port ID.

To obtain the value, run "show svp management_ip".

ip_type=?

Indicates the IP address type.

The value can be an IPv4 or IPv6 address.

ipv4_address=?

Indicates the IPv4 address.

IPv4 address does not meet the type requirement. Only A, B, and C addresses are supported.

mask=?

Indicates the IPv4 subnet mask of the management port.

-

gateway_ipv4=?

Indicates the configured IPv4 gateway.

-

ipv6_address=?

Indicates the configured IPv6 address of the management port.

-

prefix_length=?

Indicates the configured IPv6 subnet mask.

-

gateway_ipv6=?

Indicates the configured IPv6 gateway of the management port.

-

delete_gateway

Whether the original gateway needs to be deleted.

The value can be "yes" or "no", where:

  • "yes": The gateway of the port will be deleted.
  • "no": The gateway of the port will not be deleted.

Level

Administrator

Usage Guidelines

  • When the maintenance terminal and the storage system are not in the same network segment, the terminal cannot access the storage system. You have to add a router to the maintenance terminal and a gateway to the storage system so that the maintenance terminal can access the storage system.
  • Before performing the operation, ensure that the address you entered is valid and the IPv4 address must not start with 0.
  • Changing the IP address of the management port may disconnect a user that has logged in from the storage system, so log in to the storage system again after changing the IP address.
  • The maintenance terminal can access the storage system both through IPv4 and IPv6 addresses.
  • This command cannot be executed on the CLI to which you log in using the controller's management IP address. Before running this command, log in to the CLI using the SVP's management IP address.

Example

Set the IPv4 address of a specified management network port to 192.168.190.2, the subnet mask to 255.255.0.0, and the gateway address to 192.168.0.1. The command output varies depending on a specific product.

admin:/>change svp management_ip eth_port_id=P1 ip_type=ipv4_address ipv4_address=192.168.190.2 mask=255.255.0.0 gateway_ipv4=192.168.0.1 
DANGER: You are about to modify the IP address of the management network port on the SVP. This operation may disconnect you from the SVP.  
Suggestion: Ensure that the entered IP address is available.  
Have you read danger alert message carefully?(y/n)y 
Are you sure you really want to perform the operation?(y/n)

System Response

None

Translation
Download
Updated: 2019-07-12

Document ID: EDOC1000138390

Views: 226495

Downloads: 150

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next