No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Product Description

OceanStor 2800 V3 V300R006

This document is applicable to OceanStor 2800 V3. It describes the positioning, features, typical applications, architecture, specifications, environmental requirements, standards compliance, and granted certifications of the OceanStor 2800 V3 storage system.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Indicator Introduction

Indicator Introduction

After a controller enclosure is powered on, you can check the current operating status of the controller enclosure by viewing its indicators.

Indicators on the Front Panel

Figure 4-19 shows the indicators on the front panel of a 2 U 12-disk controller enclosure.

Figure 4-19 Indicators on the front panel of a 2 U 12-disk controller enclosure

1

Running indicator of the disk module

2

Location/Alarm indicator of the disk module

3

Location indicator of the controller enclosure

4

Alarm indicator of the controller enclosure

5

Power indicator/Power button of the controller enclosure

-

-

Table 4-9 describes the indicators on the front panel of the controller enclosure.

Table 4-9 Description of the indicators on the front panel of a controller enclosure

Module

No.

Indicator

Status and Description

Disk module

1

Running indicator of the disk module

  • Steady green: The disk module is working correctly.
  • Blinking green: Data is being read and written on the disk module.
  • Off: The disk module is powered off or powered on incorrectly.

2

Alarm/Location indicator of the disk module

  • Steady red: The disk module is faulty.
  • Blinking red: The disk module is being located.
  • Off: The disk module is working correctly or hot swappable.

System enclosure

3

Location indicator of the controller enclosure

  • Blinking blue: The controller enclosure is being located.
  • Off: The controller enclosure is not located.

4

Alarm indicator of the controller enclosure

  • Steady red: An alarm whose severity is major or higher is generated on the storage system.
  • Off: The storage system is running properly.

5

Power indicator/Power button of the controller enclosure

  • Steady green: The controller enclosure is powered on.
  • Blinking green (0.5 Hz): The controller enclosure is being powered on.
  • Blinking green (1 Hz): The controller enclosure is in the burn-in test.
  • Blinking green (2 Hz): The controller enclosure is in the operating system boot process or in the power-off process.
  • Off: The controller enclosure is powered off or powered by the BBUs.

Indicators on the Rear Panel

Figure 4-20 shows the indicators on the rear panel of a controller enclosure.

Figure 4-20 Indicators on the rear panel of a controller enclosure

1

Power indicator/Hot Swap button of the module

2

Running/Alarm indicator of the power module

3

Running/Alarm indicator of the BBU

4

Link/Active indicator of the management network port

5

Speed indicator of the management network port

6

Power indicator of the controller

7

Alarm indicator of the controller

8

Mini SAS HD expansion port indicator

9

Link/Active indicator of the GE electrical port

10

Speed indicator of the GE electrical port

Table 4-10 describes the indicators on the rear panel of the controller enclosure.

Table 4-10 Description of the indicators on the rear panel of a controller enclosure

Module

No.

Indicator

Status and Description

Interface module

1

Power indicator/Hot Swap button on the interface module

  • Steady green: The interface module is working correctly.
  • Blinking green: The interface module receives a hot swap request.
  • Steady red: The interface module is faulty.
  • Off: The interface module is powered off or hot swappable.

Power-BBU module

2

Running/Alarm indicator of the power module

  • Steady green: The power supply is correct.
  • Blinking green: The power input is normal but the disk enclosure is powered off.
  • Steady red: The power module is faulty.
  • Off: No external power input is found.

3

Running/Alarm indicator of the BBU

  • Steady green: The BBU is fully charged.
  • Blinking green (1 Hz): The BBU is being charged.
  • Blinking green (4 Hz): The BBU is being discharged.
  • Steady red: The BBU is faulty.

Controller

4

Link/Active indicator of the management network port

  • Steady green: The port is connected properly.
  • Blinking green: Data is being transferred.
  • Off: The port is connected abnormally.

5

Speed indicator of the management network port

  • Steady orange: Data is being transferred at the highest rate.
  • Off: The data transfer speed is lower than the highest speed.

6

Power indicator of the controller

  • Steady green: The controller is powered on.
  • Power indicator blinking green and Alarm indicator blinking red: The controller is being located.
  • Blinking green (0.5 Hz): The controller enclosure is powered on and in the BIOS boot process.
  • Blinking green (2 Hz): The controller is in the operating system boot process, or the controller is in the power-off process.
  • Off: The controller is absent or powered off.

7

Alarm indicator of the controller

  • Steady red: An alarm is generated on the controller.
  • The Alarm indicator blinking red and the Power indicator blinking green: The controller is being located.
  • Off: The controller is working correctly.

8

Mini SAS HD expansion port indicator

  • Steady blue: Data is transferred to the downstream disk enclosure at the rate of 4 x 12 Gbit/s.
  • Steady green: Data is transferred to the downstream disk enclosure at the rate of 4 x 3 Gbit/s or 4 x 6 Gbit/s.
  • Steady red: The port is faulty.
  • Off: The link to the port is down.

9

Link/Active indicator of the GE electrical port

  • Steady green: The link to the server is normal.
  • Blinking green: Data is being transferred.
  • Off: The link to the application server is down or no link exists.

10

Speed indicator of the GE electrical port

  • Steady orange: The data transfer rate between the storage system and the application server is 1 Gbit/s.
  • Off: The data transfer rate between the storage system and the application server is less than 1 Gbit/s.
Translation
Download
Updated: 2019-07-12

Document ID: EDOC1000138808

Views: 12855

Downloads: 24

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next