No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Administrator Guide

OceanStor V3 Series V300R006

This document is applicable to OceanStor 2200 V3, 2600 V3, 5300 V3, 5500 V3, 5600 V3, 5800 V3, 6800 V3, 18500 V3, and 18800 V3. Routine maintenance activities are the most common activities for the storage device, including powering on or off the storage device, managing users, modifying basic parameters of the storage device, and managing hardware components. This document is intended for the system administrators who are responsible for carrying out routine maintenance activities, monitoring the storage device, and rectifying common device faults.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Logging In to the CLI of the Storage System (Engine's Management Network Port)

Logging In to the CLI of the Storage System (Engine's Management Network Port)

The storage system allows the maintenance terminal to log in to the CLI of the storage system through the controller's management network port, to configure, manage, maintain, and query on the storage system. This document uses Windows Server 2008 as an example. Adjust the operations if you use other operating systems.

Context

  • You can log in to the CLI by using the IPv4 address or IPv6 address.
  • After connecting the maintenance terminal to the controller with cables, you can use remote login software that supports the SSH protocol (such as PuTTY) to log in to the CLI of the storage system on the maintenance terminal.
  • Default IPv4 address of the management network port: 192.168.128.101 for management module 0, 192.168.128.102 for management module 1, and 255.255.0.0 for the subnet mask.

Precautions

You must ensure that the IP addresses of the maintenance terminal and the management network port of the target controller fall in to the same network segment. This section explains how to change the management network port IP address through a serial port when the management network port IP address of the controller is not on the same network segment as that of the maintenance terminal. For details, see the change system management_ip command.

NOTE:
  • This document uses the PuTTY software as an example. You can download PuTTY from chiark website.
  • You are advised to use the latest version of PuTTY, otherwise you may fail to log in to the storage system.

Procedure

  1. Run the PuTTY software.

    The PuTTY Configuration dialog box is displayed, as shown in Figure 2-14.

    Figure 2-14 PuTTY Configuration dialog box

  2. Select Session. In the Specify the destination you want to connect to area, enter the IP address of the management network port that connects to the maintenance terminal in Host Name (or IP address) and set Connection type to SSH. Assume the IP address is 192.168.6.96 in this example.
  3. Click Open. The CLI login page is displayed, as shown in the following:

    login as: admin 
     
    Authorized users only. All activity may be monitored and reported. 
    Using keyboard-interactive authentication. 
    password: 
     
    WARNING: You have accessed the system operated by Huawei. 
    You are required to have a personal authorisation from the system administrator before you use this computer. Unauthorised access to or misuse of this system is prohibited. 
     
    For security purposes, please change the initial password and log in to the system using the new password. 
    Old password:************* 
    New password:************** 
    Reenter password:************** 
     
      System Name     : Huawei.Storage 
      Health Status : Normal 
      Running Status  : Normal 
      Total Capacity  : 6.240TB 
      SN              : XXXXX 
      Location        : 
      Product Model : XXXXX 
      Product Version : XXXRXXXCXX 
      Time            : XXXX-XX-XX/16:38:22 +08:00 
    admin:/>
    NOTE:
    • The default user name and password of the super administrator are admin and Admin@storage respectively.
    • Product Model and Product Version vary with the actual device you have logged in to. The actual interface display prevails.
    • You are advised to change your login password periodically in the future by executing the change user_password command. This reduces the password leakage risks.
    • If you forget the password of an administrator or a read-only user, contact the super administrator to run change user to reset the password. If you forget the password of the super administrator (admin by default), contact root administrator _super_admin to log in to the CLI through a serial port and run initpasswd to reset the password.
    • If you enter incorrect passwords for a specified number of times (3 times by default and equal to the value specified in Number of Incorrect Passwords on the Login Policy page), the account is automatically locked for the period of lock time.
      • For V300R006C30 and earlier versions, the lock period is 15 minutes by default.
      • For V300R006C50 and later, the lock period is 5 minutes by default

Download
Updated: 2019-07-12

Document ID: EDOC1000138854

Views: 35879

Downloads: 2043

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next