No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Administrator Guide

OceanStor V3 Series V300R006

This document is applicable to OceanStor 2200 V3, 2600 V3, 5300 V3, 5500 V3, 5600 V3, 5800 V3, 6800 V3, 18500 V3, and 18800 V3. Routine maintenance activities are the most common activities for the storage device, including powering on or off the storage device, managing users, modifying basic parameters of the storage device, and managing hardware components. This document is intended for the system administrators who are responsible for carrying out routine maintenance activities, monitoring the storage device, and rectifying common device faults.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Managing Syslog Notification

Managing Syslog Notification

You can modify the receiver server address, notification type, and alarm severity of Syslog notifications based on service requirements.

Modifying the Syslog Notification Policy

You can modify the Syslog notification type and severity based on service requirements.

Prerequisites
  • You have enabled Syslog notification.
  • You have logged in to DeviceManager as a super administrator or an administrator who has operation permission.
  • For sending alarms to the Syslog server, a storage system only sends the alarms generated after the Syslog server is configured and does not send alarms generated before the configuration.
Procedure
  1. Log in to DeviceManager.
  2. Choose Settings > Alarm Settings > Syslog Notification.
  3. Configure the Syslog notification type and severity. Table 5-19 describes the parameters.

    Figure 5-29 Syslog notification settings

    Table 5-19 Syslog notification parameters

    Parameter

    Description

    Value

    Severity

    Indicates the lowest severity of a Syslog alarm that can be sent. Possible values are Informational, Warning, Major, and Critical.

    [Example]

    Warning

    Notification Type

    Possible values are Alarm, Alarm Restore Notification, Event, and Call Home.

    [Example]

    Event

    Send Device Name

    Indicates whether the device name should be sent to the Syslog server.

    NOTE:

    After Send Device Name is enabled, the system sends device names to the Syslog notification server. You can choose Settings > Basic Information > Device Information to view device names.

    [Example]

    Enable

  4. (Optional) Click Test to test the connectivity between the storage system and Syslog server.
  5. Click Save.

    The Execution Result dialog box is displayed.

  6. Click Close.

Managing the Receiver Server Addresses of Syslog Notifications

The Syslog server can send device alarms to specified servers. You can modify the server addresses that receive Syslog notifications based on service requirements.

Prerequisites
  • You have enabled Syslog notification.
  • You have logged in to DeviceManager as a super administrator or an administrator who has operation permission.
  • For sending alarms to the Syslog server, a storage system only sends the alarms generated after the Syslog server is configured and does not send alarms generated before the configuration.
Procedure
  1. Log in to DeviceManager.
  2. Choose Settings > Alarm Settings > Syslog Notification.
  3. Manage the receiver server addresses of Syslog notifications. Table 5-20 details the operations.

    Figure 5-30 Receiver server address settings

    Table 5-20 Relevant operations

    Operation

    Procedure

    Adding an address

    1. Under the Receiver Server Address list, click Add.
    2. The Add Receiver Server Address dialog box is displayed.
    3. Specify the server address that you want to add.
      NOTE:

      An IPv4 address has the following requirements:

      • The 32-bit address is evenly divided into four fields. Each 8-bit field is expressed in dotted-decimal.
      • Each field of the IP address cannot be blank and must be an integer.
      • The value of the first field ranges from 1 to 223 (excluding 127).
      • The values of other fields range from 0 to 255.
      • The IP address cannot be a special address such as the broadcast address.

      An IPv6 address has the following requirements:

      • The 128-bit address is evenly divided into eight fields. Each 16-bit field is expressed in four hexadecimal numbers and separated with colons.
      • In each 16-bit field, zeros before integers can be removed. However, at least one digit must be reserved in each field.
      • If the IP address contains a long string of zeros, you can represent the neighboring zeros with double colons (::) in the colon-separated hexadecimal field. Each IP address contains only one double-colon (::). The double-colon (::) can also be used to represent neighboring zeros of the IP address.
      • The IP address cannot be a special address such as a network address, loop address, or multicast address.

      The domain name has the following requirements:

      • A domain name is not case-sensitive and must be an English domain name.
      • An English domain name contains 1 to 255 characters.
      • An English domain name can only contain letters (a to z, A to Z), digits (0 to 9), dots (.), and hyphens (-). It cannot start or end with a hyphen (-).
    4. Click OK.
    5. The Receiver Server Address displays the newly added server address.

    Removing a receiver server address

    In the Receiver Server Address list, select receiver server addresses that you want to remove and click Remove.

  4. (Optional) Click Test to test the connectivity between the storage system and Syslog server.
  5. Click Save.

    The Execution Result dialog box is displayed.

  6. Click Close.
Download
Updated: 2019-07-12

Document ID: EDOC1000138854

Views: 35918

Downloads: 2043

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next