No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Alarm Handling

S600-E V200R010C00

This document provides the explanations, causes, and recommended actions of alarms on the product.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
OSPF_1.3.6.1.2.1.14.16.2.1 ospfVirtIfStateChange

OSPF_1.3.6.1.2.1.14.16.2.1 ospfVirtIfStateChange

Description

OSPF/3/VIFCHG:OID [oid]: The status of the virtual interface changes. (VirtIfAreaId=[area-id], VirtIfNeighbor=[neighbor-router-id], ProcessId=[process-id], RouterId=[router-id], VirtIfState=[neighbor-state], InstanceName=[instance-name])

The interface status of the OSPF virtual link changed. The possible cause was that the router ID of the neighbor changed after the virtual link was configured or the status of the physical interface of the virtual link changed.

Attribute

Alarm ID Alarm Severity Alarm Type
1.3.6.1.2.1.14.16.2.1 Minor environmentalAlarm (6)

Parameters

Name Meaning

oid

Indicates the MIB object ID of the alarm.

VirtIfAreaId

Indicates the area ID.

VirtIfNeighbor

Indicates the router ID of the neighbor on the virtual link.

ProcessId

Indicates the process ID.

RouterId

Indicates the router ID of the local switch.

VirtIfState

Indicates the status of the neighboring interface.
  • 1: Down
  • 2: Loopback
  • 3: Waiting
  • 4: Point-to-Point
  • 5: DR
  • 6: Backup
  • 7: DROther

InstanceName

Indicates the instance name.

Impact on the System

If the interface status of the virtual link changes from Down to P2P (Point-to-Point), this trap message is informational only, and no action is required. If the interface status of the virtual link changes from P2P to Down, the virtual link will be disconnected, the OSPF route calculation will be incorrect, and services may be interrupted.

Possible Causes

1. The status of the physical interface of the virtual link changed.

2. Router ID of the neighbor on the virtual link changed.

Procedure

  1. Run the display ospf vlink command to check whether the interface status of the virtual link is P2P.

    • If so, it indicates that this trap message is informational only, and no action is required. Go to Step 4.
    • If not, go to Step 2.

  2. Run the display ospf process-id routing router-id neighbor-router-id command to check whether the area has the route to the remote switch.

    • If so, collect the configuration of the remote switch, and go to Step 3.
    • If not, run the display ospf interface command to check whether the status of the local interface is Down.
      • If so, run the display rm interface or display ip interface command to check whether the local interface goes Down.
        • If so, collect interface information, and go to Step 3.
        • If not, collect log information, and go to Step 3
      • If not, collect the configuration of the remote switch, and go to Step 3.

  3. Collect alarm information and configuration information, and then contact technical support personnel.
  4. End.

Related Information

None

Translation
Download
Updated: 2019-09-24

Document ID: EDOC1000141873

Views: 158322

Downloads: 15

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next