No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S600-E V200R010C00 Configuration Guide - User Access and Authentication

This document describes the working mechanisms, configuration procedures, and configuration examples of User Access and Authentication features, such as AAA, NAC, and Policy Association.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Configuring 802.1X Authentication (Authentication Point on the Access Switch)

Example for Configuring 802.1X Authentication (Authentication Point on the Access Switch)

Networking Requirements

In Figure 2-14, terminals in a company's offices are connected to the company's intranet through the switch. GE0/0/2 to GE0/0/n on the switch are directly connected to terminals in offices. GE0/0/1 on the switch is connected to the RADIUS server through the intranet.

To meet the company's high security requirements, configure 802.1X authentication, use the RADIUS server to authenticate terminals in offices, and deploy authentication points on GE0/0/2 to GE0/0/n of the switch.

Figure 2-14  Networking diagram for configuring 802.1X authentication

Procedure

  1. Configure AAA.

    # Create and configure the RADIUS server template rd1.

    [Switch] radius-server template rd1
    [Switch-radius-rd1] radius-server authentication 192.168.1.30 1812
    [Switch-radius-rd1] radius-server shared-key cipher Huawei@2012
    [Switch-radius-rd1] quit

    # Create the AAA authentication scheme abc and set the authentication mode to RADIUS.

    [Switch] aaa
    [Switch-aaa] authentication-scheme abc
    [Switch-aaa-authen-abc] authentication-mode radius
    [Switch-aaa-authen-abc] quit

    # Create the authentication domain huawei.com, and bind the AAA authentication scheme abc and RADIUS server template rd1 to the domain.

    [Switch-aaa] domain huawei.com
    [Switch-aaa-domain-huawei.com] authentication-scheme abc
    [Switch-aaa-domain-huawei.com] radius-server rd1
    [Switch-aaa-domain-huawei.com] quit
    [Switch-aaa] quit

    # Check whether a user can pass RADIUS authentication. (The test user test and password Huawei2012 have been configured on the RADIUS server.)

    [Switch] test-aaa test Huawei2012 radius-template rd1
    Info: Account test succeed.

  2. Configure 802.1X authentication.

    # Set the NAC mode to unified.
    NOTE:

    By default, the unified mode is enabled. After the NAC mode is changed, the device automatically restarts.

    [Switch] authentication unified-mode
    # Configure the 802.1X access profile d1.
    [Switch] dot1x-access-profile name d1
    [Switch-dot1x-access-profile-d1] quit
    NOTE:

    By default, an 802.1X access profile uses the EAP authentication mode. Ensure that the RADIUS server supports EAP; otherwise, the server cannot process 802.1X authentication request packets.

    # Configure the authentication profile p1, bind the 802.1X access profile d1 to the authentication profile, specify the domain huawei.com as the forcible authentication domain in the authentication profile.

    [Switch] authentication-profile name p1
    [Switch-authen-profile-p1] dot1x-access-profile d1
    [Switch-authen-profile-p1] access-domain huawei.com force
    [Switch-authen-profile-p1] quit

    # Bind the authentication profile p1 to GE0/0/2 to GE0/0/n and enable 802.1X authentication. The following uses the configuration of GE0/0/2 as an example. The configurations of other interfaces are similar to the configuration of GE0/0/2, and are not mentioned here.

    [Switch] interface gigabitethernet 0/0/2
    [Switch-GigabitEthernet0/0/2] authentication-profile p1
    [Switch-GigabitEthernet0/0/2] quit

    # (Recommended) Configure the source IP address and source MAC address for offline detection packets in a specified VLAN. You are advised to set the user gateway IP address and its corresponding MAC address as the source IP address and source MAC address of offline detection packets.

    [Switch] access-user arp-detect vlan 20 ip-address 192.168.2.10 mac-address 2222-1111-1234

  3. Verify the configuration.

    1. A user starts the 802.1X client on a terminal, and enters the user name and password for authentication.
    2. If the user name and password are correct, an authentication success message is displayed on the client page. The user can access the network.
    3. After users go online, you can run the display access-user access-type dot1x command on the switch to view information about online 802.1X authentication users.

Translation
Download
Updated: 2019-08-21

Document ID: EDOC1000141885

Views: 54008

Downloads: 10

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next