No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Basic Configuration

S7700 and S9700 V200R010C00

This document describes methods to use command line interface and to log in to the device, file operations, and system startup configurations.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Upgrading the System Software Using the BootROM Menu

Example for Upgrading the System Software Using the BootROM Menu

Networking Requirements

As shown in Figure 10-1, the serial port on a PC connects to the console port on a switch, and the network adapter on the PC connects to the management interface on the switch. The terminal emulation software is used for logging in to the switch.

If the system software on a switch is faulty, you cannot log in. To address this issue, use the Ethernet submenu under the BootROM menu to upload system software and specify it as the next startup system software. This enables the switch to load the system software and start an upgrade.

Figure 10-1  Networking diagram of connecting a PC to the console port on a switch
NOTE:

In this example, HyperTerminal is used as terminal emulation software. If other third-party terminal emulation software is used, see the corresponding software user guide or online help.

Configuration Roadmap

  1. Deploy an FTP server and upload the target system software to the FTP working directory. In this example, configure the PC as the FTP server, and connect the network adapter on the PC to the management interface on the switch for setting up subsequent FTP connections.
  2. Restart the switch and access the BootROM main menu.
  3. Set FTP parameters on the switch so that the switch can communicate with the FTP server. Use FTP to upload the target system software to the storage device on the switch.
  4. In the submenu for modifying the flash description, configure the uploaded system software as the next startup system software.

Procedure

  1. Configure the PC as the FTP server and copy the system software of the switch to the FTP working directory.
    1. Configure the IP address, user name, password, and working directory for the FTP server.

      Run an FTP server program on the PC, for example, wftpd32. Choose Security > Users/rights.... In the dialog box that is displayed as shown in Figure 10-2, click New User.... In the dialog box that is displayed, set the user name to user and password to huawei. Set Home Directory: to D:\BootROM. Click Done to close the dialog box. Set the IP address of the PC to 192.168.1.6 and mask to 255.255.255.0.

      Figure 10-2  Configuring the FTP server

    2. Upload the system software, such as S7700-V200R010C00.cc to the working directory (D:\BootROM) of the FTP server. The upload process is not mentioned here.
  2. Restart the switch. When the following information is displayed, press Ctrl+B, and then enter the password to access the BootROM main menu. The default BootROM password is Admin@huawei.com.

         ****************************************************
         *                                                  *
         *          Ethernet Switch BootLoad                *
         *                                                  *
         ****************************************************
    
        Copyright (C) 2000-2015 HUAWEI TECH CO., LTD
        Version : 151 Compiled at Dec 14 2013, 12:18:14 
    
        PCB Version     : LE02SRUA VER.D
        CPU L2 Cache    : 128KB
        CPU Clock Speed : 700MHz
        BUS Clock Speed : 133MHz              
        Memory Type     : DDR2 SDRAM
        Memory Size     : 1024MB
        Memory Speed    : 667MHz
    
    
                        cfcard:/  - Volume is OK
    
    Initializing CFcard ....................................................... done
    Description data is valid in nvram area
    Press Ctrl+B to enter boot menu : 1
    
    Password:       //Enter the password for accessing the BootROM menu.
                 MAIN  MENU
    
         1. Boot with default mode
         2. Boot from Flash
         3. Boot from CFCard
         4. Enter serial submenu
         5. Enter ethernet submenu
         6. Enter file system submenu
         7. Enter test submenu
         8. Enter password submenu
         9. Modify Flash description area
        10. Clear password for console user
        11. Reboot
    
    Enter your choice(1-11): 

  3. Set FTP parameters on the switch to set up an FTP connection with the PC.
    1. In the BootROM main menu, select 5 to access the Ethernet submenu.

                   MAIN  MENU
      
           1. Boot with default mode
           2. Boot from Flash
           3. Boot from CFCard
           4. Enter serial submenu
           5. Enter ethernet submenu
           6. Enter file system submenu
           7. Enter test submenu
           8. Enter password submenu
           9. Modify Flash description area
          10. Clear password for console user
          11. Reboot
      
      Enter your choice(1-11): 5
      
                  ETHERNET  SUBMENU
      
          1. Download file to SDRAM through ethernet interface and boot
          2. Download file to Flash through ethernet interface
          3. Download file to CFCard through ethernet interface
          4. Upload Configuration file to Ftp through ethernet interface
          5. Modify ethernet interface parameter
          6. Return to main menu
      
      Be sure to modify parameter before downloading
      Enter your choice(1-6):

    2. In the Ethernet submenu, select 5 to modify parameters on the Ethernet port.

                  ETHERNET  SUBMENU
      
          1. Download file to SDRAM through ethernet interface and boot
          2. Download file to Flash through ethernet interface
          3. Download file to CFCard through ethernet interface
          4. Upload Configuration file to Ftp through ethernet interface
          5. Modify ethernet interface parameter
          6. Return to main menu
      
      Be sure to modify parameter before downloading
      Enter your choice(1-6):5
      
      Note: Two protocols for download, tftp & ftp.
            The file max-length for tftp is 32M.
            You can modify the flags following the menu.
            tftp--0x80, ftp--0x0.
      
      '.' = clear field;  '-' = go to previous field;  'Ctrl+D' = quit
      
      boot device          : eth1       //No setting is required. Press "Enter".
      processor number     : 0          //No setting is required. Press "Enter".
      host name            : host       //No setting is required. Press "Enter".
      file name            : S7700-V200R001C00.CC S7700-V200R010C00.CC //Enter the name of the system software.
      inet on ethernet (e) : 192.168.10.235:ffffff00 192.168.1.3:ffffff00  //Enter the IP address of the management interface on the switch.
      inet on backplane (b): 192.168.1.1:ffffff00     //No setting is required. Press "Enter".
      host inet (h)        : 192.168.1.1 192.168.1.6     //Enter the PC's IP address.
      user (u)             : huawei user    //Enter the user name "user" for logging in to the FTP server.
      ftp password (pw) (blank = use rsh):    //Enter the password "huawei" for logging in to the FTP server.
      flags (f)            : 0x0          //FTP is used by default. No setting is required. Press "Enter".
      target name (tn)     : octeon       //No setting is required. Press "Enter".
      startup script (s)   :              //No setting is required. Press "Enter".
      other (o)            :              //No setting is required. Press "Enter".  

  4. In the Ethernet submenu, select 3 to load the system software to the CF card.

                ETHERNET  SUBMENU
    
        1. Download file to SDRAM through ethernet interface and boot
        2. Download file to Flash through ethernet interface
        3. Download file to CFCard through ethernet interface
        4. Upload Configuration file to Ftp through ethernet interface
        5. Modify ethernet interface parameter
        6. Return to main menu
    
    Be sure to modify parameter before downloading
    Enter your choice(1-6): 3
    
    boot device          : eth1
    processor number     : 0
    host name            : host
    file name            : S7700-V200R010C00.CC
    inet on ethernet (e) : 192.168.1.3:ffffff00
    inet on backplane (b): 192.168.1.1
    host inet (h)        : 192.168.1.6
    user (u)             : user
    ftp password (pw)    :
    flags (f)            : 0x0
    target name (tn)     : octeon
    startup script (s)   :
    other (o)            :
    
    
    Loading....................................................................Done!
    
    Please type a new file name for saving it.
    Press Enter key to save it named " S7700-V200R010C00.CC".
    
    Check disk space
    Writing file............................................................................
    ................................Done
    

  5. Exit from the Ethernet submenu. In the BootROM main menu, select 9 to access the submenu for modifying the flash description to specify the loaded system software for the next startup.

                 MAIN  MENU
    
         1. Boot with default mode
         2. Boot from Flash
         3. Boot from CFCard
         4. Enter serial submenu
         5. Enter ethernet submenu
         6. Enter file system submenu
         7. Enter test submenu
         8. Enter password submenu
         9. Modify Flash description area
        10. Clear password for console user
        11. Reboot
    
    Enter your choice(1-11): 9
    Modify flash description area
    Please select booting device
    Press ENTER directly for no change or input your choice
    1: Flash, 2: CFcard
    Current booting device: 2, your choice:     //No setting is required. Press "Enter".
    Current booting file name: cfcard:/S7700-V200R001C00.CC,
    Press ENTER directly for no change
    Or, please input the file name (e.g. HUAWEI.cc):S7700-V200R010C00.CC   //Enter the name of the system software to be loaded.
    
    Initiate Flash VFS...OK!
    Getting Device Index named "flash:"...OK!
    
    Saved-configuration file
    '.'=clear field; 'Ctrl+D'=quit; Enter=use current configuration
    new=change to other configuration file
    current: vrpcfg.zip
    new    :     //No setting is required. Press "Enter".
    Saved-patch file
    '.'=clear field; 'Ctrl+D'=quit; Enter=use current patch
    new=change to other patch file
    current:
    new    :     //The patch file is not upgraded. No setting is required. Press "Enter".

  6. Exit from the submenu for modifying the flash description. In the BootROM main menu, select 1 to start the switch.

                 MAIN  MENU
    
         1. Boot with default mode
         2. Boot from Flash
         3. Boot from CFCard
         4. Enter serial submenu
         5. Enter ethernet submenu
         6. Enter file system submenu
         7. Enter test submenu
         8. Enter password submenu
         9. Modify Flash description area
        10. Clear password for console user
        11. Reboot
    
    Enter your choice(1-11): 1

  7. Verify the configuration.

    # After the switch starts, run the display version command in the CLI to check whether the switch version is the target version.

    <HUAWEI> display version
    Huawei Versatile Routing Platform Software
    VRP (R) software, Version 5.160 (S7700 V200R010C00)
    Copyright (C) 2000-2014 HUAWEI TECH CO., LTD
    Quidway S7712 Terabit Routing Switch uptime is 1 week, 5 days, 22 hours, 23 minu
    tes
    ......
    

Translation
Download
Updated: 2019-04-18

Document ID: EDOC1000141895

Views: 51294

Downloads: 208

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next