No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Basic Configuration

S7700 and S9700 V200R010C00

This document describes methods to use command line interface and to log in to the device, file operations, and system startup configurations.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example of Configuring System Startup

Example of Configuring System Startup

Networking Requirements

As shown in Figure 8-4, the device has dual MPUs, and the current system software cannot meet user needs. The device must load new software version with more features. Then the device software needs to be upgraded remotely.

Figure 8-4  Networking diagram of configuring system startup

Configuration Roadmap

The configuration roadmap is as follows:

  1. Upload the new system software to the root directory of the device. If the device has dual MPUs, save the system software to both the master MPU and slave MPU.

  2. Save the current configuration so that it remains active after upgrade.

  3. Specify the system software for next startup.

  4. Specify the configuration file for next startup.

  5. Restart the device to complete upgrade.

Procedure

  1. Upload the new system software to the root directory of the device.

    Before configuration, run the display startup command to view the files for next startup.

    <HUAWEI> system-view
    [HUAWEI] sysname Switch
    [Switch] quit
    <Switch> display startup
    MainBoard:
      Configured startup system software:        cfcard:/basicsoft.cc
      Startup system software:                   cfcard:/basicsoft.cc
      Next startup system software:              cfcard:/basicsoft.cc
      Startup saved-configuration file:          cfcard:/vrpcfg.zip
      Next startup saved-configuration file:     cfcard:/vrpcfg.zip
      Startup paf file:                          default
      Next startup paf file:                     default
      Startup license file:                      default
      Next startup license file:                 default
      Startup patch package:                     NULL
      Next startup patch package:                NULL
    SlaveBoard:
      Configured startup system software:        cfcard:/basicsoft.cc
      Startup system software:                   cfcard:/basicsoft.cc
      Next startup system software:              cfcard:/basicsoft.cc
      Startup saved-configuration file:          cfcard:/vrpcfg.zip
      Next startup saved-configuration file:     cfcard:/vrpcfg.zip
      Startup paf file:                          default
      Next startup paf file:                     default
      Startup license file:                      default
      Next startup license file:                 default
      Startup patch package:                     NULL
      Next startup patch package:                NULL

    # Upload the new system software to the device. This example uses FTP to transfer the system software. Configure the device as an FTP server and upload the system software to the device from the FTP client. Make sure there is enough space in the storage device before uploading files. If the space is insufficient, delete unnecessary files to free up space in the storage device.

    <Switch> system-view
    [Switch] ftp server enable
    [Switch] aaa
    [Switch-aaa] local-user huawei password irreversible-cipher Helloworld@6789
    [Switch-aaa] local-user huawei service-type ftp
    [Switch-aaa] local-user huawei ftp-directory cfcard:
    [Switch-aaa] local-user huawei privilege level 15
    [Switch-aaa] quit
    [Switch] quit
    

    # Run the ftp 10.1.1.1 command in the command line window of the PC to set up an FTP connection with the device. Run the put command to upload new system software newbasicsoft.cc. After the upload completes, run the dir command to check the system software.

    <Switch> dir
    Directory of cfcard:/
    
      Idx  Attr     Size(Byte)  Date        Time       FileName
        0  drw-              -  Apr 16 2012 13:19:58   logfile
        1  -rw-     85,925,409  Apr 16 2012 13:18:02   basicsoft.cc
        2  -rw-              4  Oct 27 2011 17:25:22   snmpnotilog.txt
        3  -rw-          6,033  Jul 16 2012 16:40:02   private-data.txt
        4  -rw-          3,275  Jul 14 2012 14:18:08   vrpcfg.zip
        5  drw-              -  Nov 14 2011 19:14:26   sysdrv 
        6  drw-     88,239,759  Jul 16 2012 19:14:26   newbasicsoft.cc
    ...
    
    509,256 KB total (52,752 KB free)

  2. Save the current configuration to both the master and slave MPUs.

    <Switch> save
    The current configuration will be written to the device.                        
    Are you sure to continue? [Y/N]y                                                 
    Now saving the current configuration to the slot 0 .                            
    Info: Save the configuration successfully. 

  3. Specify the system software to be loaded for next startup.

    # Configure the system software for next startup on the master MPU.

    <Switch> startup system-software newbasicsoft.cc

    # Configure the system software for next startup on the slave MPU.

    <Switch> startup system-software newbasicsoft.cc slave-board

  4. Specify the configuration file for next startup.

    <Switch> startup saved-configuration vrpcfg.zip
    NOTE:
    • In step 1, you can run the display startup command to check the configuration file for next startup. The message "Next startup saved-configuration file: cfcard:/vrpcfg.zip" will be displayed. This means that the vrpcfg.zip configuration file has been specified for next startup, so skip this step. To specify another file for next startup, perform this step.

    • If a configuration file is specified for next startup on the master MPU, the slave MPU automatically updates the configuration for next startup.

  5. Check the configuration.

    # Run the following command to view the system software and configuration file for next startup.

    <Switch> display startup
    MainBoard:
      Configured startup system software:        cfcard:/basicsoft.cc
      Startup system software:                   cfcard:/basicsoft.cc
      Next startup system software:              cfcard:/newbasicsoft.cc
      Startup saved-configuration file:          cfcard:/vrpcfg.zip
      Next startup saved-configuration file:     cfcard:/vrpcfg.zip
      Startup paf file:                          default
      Next startup paf file:                     default
      Startup license file:                      default
      Next startup license file:                 default
      Startup patch package:                     NULL
      Next startup patch package:                NULL
    SlaveBoard:
      Configured startup system software:        cfcard:/basicsoft.cc
      Startup system software:                   cfcard:/basicsoft.cc
      Next startup system software:              cfcard:/newbasicsoft.cc
      Startup saved-configuration file:          cfcard:/vrpcfg.zip
      Next startup saved-configuration file:     cfcard:/vrpcfg.zip
      Startup paf file:                          default
      Next startup paf file:                     default
      Startup license file:                      default
      Next startup license file:                 default
      Startup patch package:                     NULL
      Next startup patch package:                NULL

  6. Restart the device.

    # Since the configuration file has been saved, run the reboot fast command to restart the device quickly.

    <Switch> reboot fast
    System will reboot! Continue? [Y/N]:y                                            
    Info: system is rebooting ,please wait...

  7. Verify the configuration.

    # Wait for several minutes until the device restart is complete. Run the display version command to check the current system version. If the current system software is new, the device has been successfully upgraded.

    The display version command output is not provided here.

Configuration File

#
FTP server enable
#
vlan batch 10
#
aaa
 local-user huawei password irreversible-cipher $1a$C"d3YGyf411I-z$.si9E-TOVAw^&9Ttgw%WAr0'~XC9n/;goO~V9XdV6aOE'$
 local-user huawei privilege level 15
 local-user huawei ftp-directory cfcard:
 local-user huawei service-type ftp
#
interface Vlanif10
 ip address 10.1.1.1 255.255.255.0 
#
interface GigabitEthernet1/0/1
 port link-type trunk
 port trunk allow-pass vlan 10
#
return
Translation
Download
Updated: 2019-04-18

Document ID: EDOC1000141895

Views: 51949

Downloads: 210

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next