No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Basic Configuration

S7700 and S9700 V200R010C00

This document describes methods to use command line interface and to log in to the device, file operations, and system startup configurations.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Licensing Requirements and Limitations for EasyDeploy

Licensing Requirements and Limitations for EasyDeploy

Involved Network Elements

EasyDeploy networking involves the following components:
  • DHCP server
  • File server
  • Commander and client

Licensing Requirements

EasyDeploy is a basic feature of a switch and is not under license control.

Version Requirements

Table 2-1  Products and versions supporting EasyDeploy

Series

Product Model

Software Version

S9700

S9703, S9706, S9712

V200R003C00, V200R005C00, V200R006C00, V200R007C00, V200R008C00, V200R009C00, V200R010C00, V200R011C10

S7700

S7703, S7706, S7712

V200R003C00, V200R005C00, V200R006C00, V200R007C00, V200R008C00, V200R009C00, V200R010C00, V200R011C10

NOTE:
To know details about software mappings, see Hardware Query Tool.

Feature Limitations

  • The EasyDeploy cannot be applied on an IPv6 or VPN network.
  • EasyDeploy is mutually exclusive with USB-based deployment and SVF.
  • In the unconfigured device deployment or faulty device replacement scenarios, if you log in to a device to be configured through its console interface, the device stops the EasyDeploy process and starts to operate.
  • In the unconfigured device deployment and faulty device replacement scenarios, EasyDeploy can only run on the service interfaces in the default VLAN.
  • In the unconfigured device deployment scenario, you can decide whether to specify the configuration file based on actual requirements. If the configuration file is not specified and the upgrade system software is specified, you also need to specify the upgrade version number.
  • There is no limitation on the network location of the Commander as long as there are reachable routes between the Commander and clients that obtain IP addresses.
  • EasyDeploy allows a stack system to act as a client. In this case, the client MAC address is the system MAC address of the stack system, and the client ESN is the ESN of the stack master switch.
  • When the EasyDeploy topology collection function is enabled, the Commander that initiates topology collection will receive a large number of protocol packets if the Network Topology Discovery Protocol (NTDP) needs to collect the topology of more than 200 devices. If the rate of NTDP packets exceeds the default committed access rate (CAR), NTDP packets will be dropped. To prevent packet loss from affecting topology collection, you can run the car (attack defense policy view) command to increase the central processor CAR (CPCAR) of NTDP packets.
  • Datagram Transport Layer Security (DTLS) encryption

    • On a configured switch, EasyDeploy supports DTLS encryption. By default, DTLS encryption is enabled. In the unconfigured device deployment scenario, a switch can be normally deployed regardless of whether DTLS encryption is enabled.

    • If an active/standby switchover occurs on the Commander or between clients when DTLS encryption is enabled, the clients need to go online again. If DTLS encryption is disabled, an active/standby switchover does not affect online management of clients.

    • If a client in a version earlier than V200R010C00 needs to be managed by the Commander in V200R010C00 or a later version and DTLS encryption is enabled on the Commander, you must upgrade the system software of the client to V200R010C00 or a later version. Otherwise, the client cannot join the existing network.

    • If a client in V200R010C00 or a later version needs to be managed by the Commander in a version earlier than V200R010C00, you need to run the easy-operation dtls disable command on the client to disable DTLS encryption.

  • Specifications

    Table 2-2 lists the product models that support the EasyDeploy and specifications of this feature.

    Table 2-2  EasyDeploy specifications
    Role Product Model Version Maximum Number of Managed Clients Description
    Commander S7700 and S9700

    S7700 and S9700: V200R003C00 and later

    255
    • If the clients are modular switches, EasyDeploy can only be applied to the batch upgrade and batch configuration scenarios.
    • If the clients are fixed switches, EasyDeploy applies to the batch upgrade, batch configuration, unconfigured device deployment, and faulty device replacement scenarios.
    S12700 V200R005C00 and later 255
    S5700HI, S5710HI, S6700EI V200R003C00 to V200R005C00 128
    S5700EI and S5710EI 64
    S5720HI V200R006C00 and later 128
    S5720EI V200R007C00 and later 128
    S6720EI V200R008C00 and later 128
    S6720S-EI V200R009C00 and later 128
    Client
    • All fixed switch models except S1720GFR, S1720GW-E, S1720GWR-E and S1720X-E
    • All modular switch models
    V200R003C00 and later -
  • Table 2-3 lists the types of files that can be loaded through EasyDeploy in various scenarios.

    Table 2-3  File types supported by EasyDeploy
    Usage Scenario File Type
    Unconfigured device deployment System software, patch file, web page file, configuration file, and user-defined file
    Faulty device replacement System software, patch file, web page file, configuration file (automatically backed up), and user-defined file
    Batch upgrade System software, patch file, web page file, configuration file, license file (supported when the clients are modular switches), and user-defined file
    Batch configuration Command script

    Each device can download a maximum of three user-defined files, including batch file and login headline file.

Translation
Download
Updated: 2019-08-21

Document ID: EDOC1000141895

Views: 57922

Downloads: 214

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next