No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - IP Unicast Routing

S7700 and S9700 V200R010C00

This document describes IP Unicast Routing configurations supported by the switch, including the principle and configuration procedures of IP Routing Overview, Static Route, RIP, RIPng, OSPF, OSPFv3, IS-IS(IPv4), IS-IS(IPv6), BGP, Routing Policy ,and PBR, and provides configuration examples.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring Dynamic BFD for IPv6 IS-IS

Configuring Dynamic BFD for IPv6 IS-IS

Context

The switch supports dynamic BFD for IPv6 IS-IS, but not static BFD for IPv6 IS-IS.

Without BFD, connection status between an IS-IS device and its neighbors can be monitored only by exchanging Hello packets at intervals. The minimum allowable sending interval is 3s, and a neighbor is declared Down after at least three intervals during which no response Hello packet is received from the neighbor. IS-IS takes more than one second to detect that a neighbor becomes Down, resulting in loss of a large amount of high-speed data.

BFD provides millisecond-level fault detection. After detecting a link or node failure, BFD will notify IS-IS of the failure. Traffic is rapidly switched to the backup link or node.

Pre-configuration Tasks

Before configuring dynamic BFD for IPv6 IS-IS, complete the following tasks:

  • Configure IPv6 addresses for interfaces to ensure that neighbor nodes are reachable.

  • Configure IPv6 IS-IS functions to ensure that each node is reachable at the network layer.

Configuration Roadmap

The configuration roadmap is as follows:

No.

Data

1

Nodes to be enabled with BFD for IPv6 IS-IS

2

Number of the IS-IS process to be enabled with BFD

3

Type and number of each interface to be enabled with BFD

4

Minimum interval at which BFD packets are sent

5

Minimum interval at which BFD packets are received

6

BFD detection multiplier

You can use either of the following methods to enable BFD for IPv6 IS-IS:

Procedure

  • Enable dynamic BFD for an IS-IS IPv6 process.
    1. Run:

      system-view

      The system view is displayed.

    2. Run:

      bfd

      BFD is enabled globally.

    3. Run:

      quit

      The system view is displayed.

    4. Run:

      isis process-id

      The IS-IS view is displayed.

    5. Run:

      ipv6 bfd all-interfaces enable

      BFD for IS-IS is enabled.

      After BFD is enabled globally and the neighbor status is Up, default BFD parameters will be used to establish BFD sessions on all interfaces.

    6. (Optional) Run:

      ipv6 bfd all-interfaces { min-rx-interval receive-interval | min-tx-interval transmit-interval | detect-multiplier multiplier-value } *

      The parameters for establishing BFD sessions are set for all interfaces.

      The command execution result is applicable to BFD session parameters on all IS-IS interfaces.

    7. Run:

      quit

      The system view is displayed.

      To disable the BFD function on an interface, run the isis ipv6 bfd block command in the interface view to disable the interface from establishing BFD sessions.

  • Enable dynamic BFD on an IS-IS IPv6 interface.
    1. Run:

      system-view

      The system view is displayed.

    2. Run:

      bfd

      BFD is enabled globally.

    3. Run:

      quit

      The system view is displayed.

    4. Run:

      interface interface-type interface-number

      The view of the specified interface is displayed.

    5. (Optional) On an Ethernet interface, run undo portswitch

      The interface is switched to Layer 3 mode.

      By default, an Ethernet interface works in Layer 2 mode.

    6. Run:

      isis ipv6 bfd enable

      BFD is enabled on the interface.

    7. (Optional) Run:

      isis ipv6 bfd { min-rx-interval receive-interval | min-tx-interval transmit-interval | detect-multiplier multiplier-value } *

      Run this command when BFD session parameters need to be configured for a specified interface.

Checking the Configurations

After configuring dynamic BFD for IPv6 IS-IS, you can check information about the BFD session and BFD for IPv6 IS-IS on an interface.
  • Run the display isis [ process-id | vpn-instance vpn-instance-name ] ipv6 bfd session { all | peer ipv6-address | interface interface-type interface-number } command to check information about a BFD session.

  • Run the display isis [ process-id ] ipv6 bfd interface command to check the configurations of BFD for IPv6 IS-IS on the specified interface.

Translation
Download
Updated: 2019-08-21

Document ID: EDOC1000141900

Views: 190509

Downloads: 194

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next