No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - IP Unicast Routing

S7700 and S9700 V200R010C00

This document describes IP Unicast Routing configurations supported by the switch, including the principle and configuration procedures of IP Routing Overview, Static Route, RIP, RIPng, OSPF, OSPFv3, IS-IS(IPv4), IS-IS(IPv6), BGP, Routing Policy ,and PBR, and provides configuration examples.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring Static BFD for RIP

Configuring Static BFD for RIP

Context

BFD provides link failure detection featuring light load and high speed. Static BFD for RIP is a method to implement the BFD function.

Establishing BFD sessions between RIP neighbors can rapidly detect faults on links and speed up response of RIP to network topology changes. Static BFD implements the following functions:
  • One-arm BFD

    If not all devices on a network support BFD, configure one-arm BFD to implement fault detection.

  • Two-arm BFD

    If all the devices on a network support BFD, configure two-arm BFD to implement fault detection.

To configure a static BFD session, you need to set parameters for the BFD session.

Procedure

  1. Enable BFD globally.
    1. Run:

      system-view

      The system view is displayed.

    2. Run:

      bfd

      BFD is enabled globally.

    3. Run:

      quit

      Return to the system view.

    NOTE:

    To configure one-arm BFD, go to Step 2. To configure two-arm BFD, go to Step 3.

  2. Configure one-arm BFD.
    1. Run:

      bfd session-name bind peer-ip peer-ip interface interface-type interface-number [ source-ip source-ip ] one-arm-echo

      BFD is enabled between the specified interface and peer device.

      If a peer IP address and a local interface are specified, BFD detects only a single-hop link, that is, a route with the interface specified in the bfd command as the outbound interface and with the peer IP address specified in the peer-ip command as the next-hop address.

      NOTE:

      When configuring the one-arm Echo function on the device, set the source-ip source-ip to the IP address of an interface on the device. Ensure that the peer device can ping this IP address.

    2. Run:

      discriminator local discr-value

      The local discriminator is set.

    3. (Optional) Run:

      min-echo-rx-interval interval

      The minimum interval at which BFD packets are received is configured.

    4. Run:

      commit

      The configuration is committed.

    5. Run:

      quit

      Return to the system view.

  3. Configure two-arm BFD.
    1. Run:

      bfd session-name bind peer-ip ip-address [ interface interface-type interface-number ] [ source-ip ip-address ]

      BFD binding is created.

      If a peer IP address and a local interface are specified, BFD detects only a single-hop link, that is, a route with the interface specified in the bfd command as the outbound interface and with the peer IP address specified in the peer-ip command as the next-hop address.

    2. Set discriminators.

      • Run:

        discriminator local discr-value

        The local discriminator is set.

      • Run:

        discriminator remote discr-value

        The remote discriminator is set.

      The local discriminator must be the remote discriminator of the device on the other end; otherwise, a BFD session cannot be established. The local and remote discriminators cannot be modified after being configured.

      NOTE:

      local discr-value set on the local device is the same as that of remote discr-value set on the remote device.remote discr-value set on the local device is the same as that of local discr-value set on the remote device.

    3. Run:

      commit

      The configuration is committed.

    4. Run:

      quit

      Return to the system view.

  4. Enable static BFD on an interface.
    1. Run:

      interface interface-type interface-number

      The view of the specified interface is displayed.

    2. (Optional) On an Ethernet interface, run undo portswitch

      The interface is switched to Layer 3 mode.

      By default, an Ethernet interface works in Layer 2 mode.

    3. Run:

      rip bfd static

      Static BFD is enabled on the interface.

    4. Run:

      quit

      Return to the system view.

Checking the Configuration

After configuring static BFD for RIP,
  • Run the display rip process-id interface [ interface-type interface-number ] verbose command to check BFD for RIP configurations on the specified interface.
Translation
Download
Updated: 2019-08-21

Document ID: EDOC1000141900

Views: 179216

Downloads: 192

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next