No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - MPLS

S7700 and S9700 V200R010C00

This document describes MPLS configurations supported by the switch, including the principle and configuration procedures of static LSPs, MPLS LDP, MPLS TE, MPLS QoS, MPLS OAM, Seamless MPLS, and MPLS common features, and provides configuration examples.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuration Overview

Configuration Overview

Applicable Environment

MPLS OAM can detect an ordinary LSP and a TE LSP. Before configuring MPLS OAM, an LSP must be configured. This section describes the applicable environment, pre-configuration tasks, data preparation, and configuration procedure of configuring MPLS OAM detection.

The switches provide MPLS OAM to detect the connectivity of a Resource Reservation Protocol TE (RSVP-TE) LSP, a static constraint-based routing LSP (CR-LSP), or a static LSP.

To implement MPLS OAM detection, create a reverse LSP for bearing BDI packets. The type of the reverse LSP can be different from that of the tested LSP, but the reverse LSP must be bound to a TE tunnel.

Pre-configuration Tasks

Before configuring basic MPLS OAM functions for LSP, complete the following tasks:

  • Configure basic MPLS functions.

  • Create a forward LSP (the LSP is detected by OAM, and bound to the TE tunnel).

  • Create a reverse LSP.

NOTE:

If the forward LSP is static and the reverse LSP is dynamic and in shared mode, specify lsrid ingress-lsr-id and tunnel-id tunnel-id when creating a forward LSP with the static-lsp egress or static-cr-lsp egress command. For details on how to create the LSP bound to a TE tunnel, see "MPLS TE Configuration."

Data Preparation

Prepare the following information before configuring basic MPLS OAM functions.

No.

Data

1

Ingress: Tunnel interface number of the detected LSP

2

(Optional) Ingress: reverse tunnel
  • If a static LSP or a static CR-LSP acts as the reverse tunnel, the name of the static LSP or the static CR-LSP is required.
  • If a dynamic LSP (RSVP-TE LSP) acts as the reverse tunnel, the LSR ID and tunnel ID are required.

3

Egress: Tunnel interface number of the reverse LSP and protection mode

4

Egress: detected LSP
  • If a static LSP or a static CR-LSP is to be detected, the name of the LSP, LSR ID, and tunnel ID are required.
  • If a dynamic LSP (RSVP-TE LSP) is to be detected, the LSR ID and tunnel ID are required.

5

(Optional) MPLS OAM parameters
  • On the ingress: detection type, frequency of FFD packet transmission, and priority of the detection packet
  • On the egress: detection type, frequency of FFD packet transmission, status of the auto protocol (enabled or disabled), timeout period of the auto protocol, and frequency of BDI packet transmission
NOTE:
  • The reverse LSP must be specified on the egress. Otherwise, BDI packets cannot be correctly sent to the source end.

  • If a shared reverse LSP is used, do not specify the reverse LSP on the ingress.

Translation
Download
Updated: 2019-04-18

Document ID: EDOC1000141902

Views: 69720

Downloads: 189

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next