No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - MPLS

S7700 and S9700 V200R010C00

This document describes MPLS configurations supported by the switch, including the principle and configuration procedures of static LSPs, MPLS LDP, MPLS TE, MPLS QoS, MPLS OAM, Seamless MPLS, and MPLS common features, and provides configuration examples.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring BFD with Specific Parameters on the Egress Node

Configuring BFD with Specific Parameters on the Egress Node

Context

BFD parameters on the egress node include the local and remote discriminators, intervals for sending and receiving BFD packets, and local BFD detection multiplier. The BFD parameters affect BFD session setup.

You can adjust the local detection time according to the network situation. On an unstable link, if a small detection time is used, a BFD session may flap. You can increase the detection time of the BFD session.

NOTE:

Actual interval for the local device to send BFD packets = MAX {locally configured interval for sending BFD packets, remotely configured interval for receiving BFD packets}

Actual interval for the local device to receive BFD packets = MAX {remotely configured interval for sending BFD packets, locally configured interval for receiving BFD packets}

Local detection time = Actual interval for receiving BFD packets x Remotely configured BFD detection multiplier

Perform the following steps on the egress node of the LSP.

Procedure

  1. Run:

    system-view

    The system view is displayed.

  2. Run:

    bfd

    This node is enabled with global BFD. The global BFD view is displayed.

    By default, global BFD is disabled.

  3. Run:

    quit

    Return to the system view.

  4. Configure a reverse tunnel to inform the ingress node of a fault if the fault occurs. The reverse tunnel can be the IP link, LSP, or TE tunnel. To ensure that BFD packets are received and sent along the same path, an LSP or TE tunnel is preferentially used to inform the egress node of an LSP fault. If the configured reverse tunnel requires BFD detection, configure a pair of BFD sessions for it. Run the following commands as required.

    • For the IP link, run:

      bfd cfg-name bind peer-ip peer-ip [ vpn-instance vpn-instance-name ] [ interface interface-type interface-number ] [ source-ip source-ip ]
    • For the dynamic LSP, run:

      bfd cfg-name bind ldp-lsp peer-ip ip-address nexthop ip-address [ interface interface-type interface-number ]
    • For the static LSP, run:

      bfd cfg-name bind static-lsp lsp-name
    • For MPLS TE, run:

      bfd cfg-name bind mpls-te interface tunnel interface-number [ te-lsp [ backup ] ]

  5. Set local and remote discriminators of a BFD session.

    • Run:

      discriminator local discr-value

      The local discriminator is configured.

    • Run:

      discriminator remote discr-value

      The remote discriminator is configured.

    NOTE:

    The local identifier and remote identifier on both ends of a BFD session must accord with each other. The session cannot be established correctly otherwise. In addition, the local identifier and remote identifier cannot be modified after configuration.

  6. (Optional) Run:

    min-tx-interval interval

    The interval for sending BFD packets is set on the local device.

  7. (Optional) Run:

    min-rx-interval interval

    The interval for receiving BFD packets is set on the local device.

  8. (Optional) Run:

    detect-multiplier multiplier

    The local BFD detection multiplier is set.

    The default value is 3.

  9. (Optional) Run:

    process-pst

    The changes of the BFD session status can be advertised to the upper-layer application.

    By default, a static BFD session cannot report faults of the monitored service module to the system.

    If an LSP is used as a reverse tunnel to notify the ingress of a fault, you can run this command to allow the reverse tunnel to switch traffic if the BFD session goes Down. If a single-hop IP link is used as a reverse tunnel, this command can be configured. Because the process-pst command can be only configured for BFD single-link detection.

  10. Run:

    commit

    The configuration is committed.

Translation
Download
Updated: 2019-04-18

Document ID: EDOC1000141902

Views: 69666

Downloads: 189

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next