No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - MPLS

S7700 and S9700 V200R010C00

This document describes MPLS configurations supported by the switch, including the principle and configuration procedures of static LSPs, MPLS LDP, MPLS TE, MPLS QoS, MPLS OAM, Seamless MPLS, and MPLS common features, and provides configuration examples.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring MPLS OAM on the Egress

Configuring MPLS OAM on the Egress

Context

When configuring OAM on the egress of an LSP, you can determine whether to enable the OAM auto protocol. By default, the OAM auto protocol is enabled.

Perform the following steps on the egress of the LSP.

Procedure

  1. Run:

    system-view

    The system view is displayed.

  2. Run:

    mpls

    The MPLS view is displayed.

  3. Run:

    mpls oam

    MPLS OAM is enabled globally.

  4. Run:

    quit

    Return to the system view.

  5. Configure OAM parameters on the egress.

    • If the auto protocol will be used, run:

      mpls oam egress { lsp-name lsp-name | lsr-id ingress-lsr-id tunnel-id tunnel-id } [ auto-protocol [ overtime over-time ] ] [ backward-lsp tunnel interface-number [ private | share ]  [ bdi-frequency { detect-freq | per-second } ] ]

      The OAM auto protocol is enabled.

    • If the auto protocol will not be used, run:

      mpls oam egress { lsp-name lsp-name | lsr-id ingress-lsr-id tunnel-id tunnel-id } type { cv | ffd frequency ffd-fre } [ backward-lsp tunnel interface-number [ private | share ] [ bdi-frequency { detect-freq | per-second } ] ]

      OAM parameters are configured on the egress when the OAM auto protocol is disabled.

    If lsrid ingress-lsr-id and tunnel-id tunnel-id are specified when you create an LSP with the static-lsp egress lsp-name [ incoming-interface interface-type interface-number ] in-label in-label [ lsrid ingress-lsr-id tunnel-id tunnel-id ] or static-cr-lsp egress lsp-name [ incoming-interface interface-type interface-number ] in-label in-label [ lsrid ingress-lsr-id tunnel-id tunnel-id ] command, you can specify these two parameters in this step. Otherwise, you can only specify the parameter lsp-name lsp-name.

    By default, the OAM auto protocol is enabled. The timeout period for the first packet to wait for response is 5 minutes.

    By default, the reverse LSP is in shared mode unless it is a static LSP or a CR-LSP. In this case, it is in private mode.

    The detect-freq parameter specifies the frequency at which BDI packets are sent through the reverse LSP.

    NOTE:

    If the OAM auto protocol is enabled in Step 5, Step 6 is not necessary. When the egress receives the first CV/FFD packet, it automatically records the packet type and the frequency at which CV/FFD packets are sent, and starts to detect the connectivity.

  6. Run:

    mpls oam egress enable { all | lsp-name lsp-name | lsr-id ingress-lsr-id tunnel-id tunnel-id }

    OAM is enabled on the egress.

Translation
Download
Updated: 2019-08-21

Document ID: EDOC1000141902

Views: 73367

Downloads: 189

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next