No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - IP Multicast

S7700 and S9700 V200R010C00

This document describes IP multicast basics and how to configure IP multicast features, including IGMP/MLD, PIM (IPv4&IPv6), MSDP, multicast VPN, Layer 3 multicast CAC, Layer 2 multicast CAC, IGMP/MLD snooping, and multicast VLAN, IPv4&IPv6 multicast route management, static multicast MAC address, multicast network.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Adjusting the Control Parameters for Establishing Neighbor Relationships

Adjusting the Control Parameters for Establishing Neighbor Relationships

Pre-configuration Tasks

Before configuring control parameters for establishing neighbor relationships, complete the following tasks:

  • Configure an IPv6 unicast routing protocol to ensure normal unicast routing on the network.
  • Enable IPv6 PIM-SM.

Configuration Process

Configuration tasks in this section can be performed in any sequence.

Adjusting the Control Parameters for Hello Messages

Context

PIM devices send Hello messages periodically to maintain PIM neighbor relationships. When a PIM device receives a Hello message from a neighbor, the PIM device starts the timer and sets the timer to the holdtime of Hello messages. If the PIM device does not receive a new Hello message from the neighbor within the holdtime, it considers the neighbor invalid or unreachable. Therefore, the interval for a PIM device to send Hello messages must be smaller than the holdtime of Hello messages.

If multiple PIM devices transmit Hello messages simultaneously, a conflict occurs on the network. To solve this problem, when a PIM device receives a Hello message, it waits a period before transmitting the Hello message. This period is a random value and is smaller than the maximum delay for triggering Hello messages.

NOTE:

The interval for sending Hello messages and the holdtime of Hello messages can be set either globally or on an interface. If you configure the two parameters in the global PIM-IPv6 view and in the interface view simultaneously, the configuration in the interface view takes effect.

You can configure the maximum delay for triggering Hello messages only in the interface view.

Default Configuration

Table 5-16 lists default configuration of control parameters for Hello messages.

Table 5-16  Default configuration of control parameters for Hello messages
Parameter Default Setting

Interval for sending Hello messages

30s

Holdtime of Hello messages

105s

Maximum delay for triggering Hello messages

5s

Procedure

  • Global configuration
    1. Run:

      system-view

      The system view is displayed.

    2. Run:

      pim-ipv6

      The PIM-IPv6 view is displayed.

    3. Run:

      timer hello interval

      The interval for sending Hello messages is configured.

    4. Run:

      hello-option holdtime interval

      The holdtime of Hello messages is configured.

  • Configuration on an interface
    1. Run:

      system-view

      The system view is displayed.

    2. Run:

      interface interface-type interface-number

      The interface view is displayed.

    3. (Optional) On an Ethernet interface, run undo portswitch

      The interface is switched to Layer 3 mode.

      By default, an Ethernet interface works in Layer 2 mode.

    4. Run:

      pim ipv6 timer hello interval

      The interval for sending Hello messages is configured.

    5. Run:

      pim ipv6 hello-option holdtime interval

      The holdtime of Hello messages is configured.

    6. Run:

      pim ipv6 triggered-hello-delay interval

      The maximum delay for triggering Hello messages is configured.

Enabling Downstream Neighbor Tracking

Context

When sending a Hello message, a PIM device generates a Generation ID and adds it to the message. If the status of the device changes, the device generates a new Generation ID. When a neighboring device receives the Hello message and finds that the Generation ID has changed, it sends a Join message to refresh the neighbor relationship. Devices on a shared network segment use a listening mechanism to prevent multiple devices from simultaneously sending Join messages to the same upstream device. When a device detects the Join message sent from another device to an upstream device, it does not send Join messages to this upstream PIM device. Therefore, the upstream PIM neighbor with a changed Generation ID cannot refresh neighbor relationships with each downstream neighbor.

After the neighbor tracking function is enabled, PIM devices no longer trigger Join message suppression when they detect a Join message sent by another PIM device. Instead, they keep sending Join messages to the same upstream neighbor.

NOTE:

The neighbor tracking function can be enabled globally or on an interface. If you configure the neighbor tracking function in the global PIM-IPv6 view and in the interface view simultaneously, the configuration in the interface view takes effect.

The neighbor tracking function can be implemented only when all devices on the shared network segment have this function enabled.

Procedure

  • Global configuration
    1. Run:

      system-view

      The system view is displayed.

    2. Run:

      pim-ipv6

      The PIM-IPv6 view is displayed.

    3. Run:

      hello-option neighbor-tracking

      The function of tracking a downstream neighbor is enabled.

  • Configuration on an interface
    1. Run:

      system-view

      The system view is displayed.

    2. Run:

      interface interface-type interface-number

      The interface view is displayed.

    3. (Optional) On an Ethernet interface, run undo portswitch

      The interface is switched to Layer 3 mode.

      By default, an Ethernet interface works in Layer 2 mode.

    4. Run:

      pim ipv6 hello-option neighbor-tracking

      The function of tracking a downstream neighbor is enabled.

Configuring PIM Neighbor Filtering

Context

The switch supports different neighbor filtering policies to ensure secure and effective multicast transmission in a PIM-SM domain. Perform the following operations to filter neighbors:
  • Configure a valid neighbor address range to prevent unauthorized neighbors from connecting to the network or participating in DR election.
  • Configure the switch to reject Hello messages without Generation IDs so that switch connects to normally working PIM neighbors.
  • Enable the PIM neighbor check function to discard Join/Prune messages and Assert messages that are not sent from neighbors or send Join/Prune messages and Assert messages only to neighbors.

Procedure

  1. Run:

    system-view

    The system view is displayed.

  2. Run:

    interface interface-type interface-number

    The interface view is displayed.

  3. (Optional) On an Ethernet interface, run undo portswitch

    The interface is switched to Layer 3 mode.

    By default, an Ethernet interface works in Layer 2 mode.

  4. Run:

    pim ipv6 neighbor-policy { basic-acl6-number | acl6-name acl6-name }

    The range of valid neighbor addresses is configured.

    • The switch will no longer receive Hello messages from IPv6 PIM neighbors whose IP addresses are not within the configured valid range. When the holdtime of Hello messages expires, the neighbor relationship between these IPv6 PIM devices and the switch will be terminated.

    • When configuring an ACL rule for the interface, use the permit parameter to configure the interface to accept only Hello messages with source addresses in a specified range. If no rule is configured in the ACL, the interface discards Hello messages from all source addresses.

  5. Run:

    pim ipv6 require-genid

    The device is configured to receive only Hello messages that contain Generation IDs.

  6. Run:

    quit

    The system exits from the interface view.

  7. Run:

    pim-ipv6

    The PIM-IPv6 view is displayed.

  8. Run:

    neighbor-check { receive | send }

    The PIM neighbor check function is enabled.

Checking the Configuration

Prerequisites

After the control parameters for establishing the neighbor relationship are adjusted, check information about the IPv6 PIM interface and the IPv6 PIM neighbor.

Procedure

  • Run the display pim ipv6 interface [ interface-type interface-number | up | down ] [ verbose ] command to check IPv6 PIM information on an interface.
  • Run the display pim ipv6 neighbor [ ipv6-link-local-address | interface interface-type interface-number | verbose ] * command to check information about IPv6 PIM neighbors.
Translation
Download
Updated: 2019-08-21

Document ID: EDOC1000141903

Views: 145951

Downloads: 111

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next